Question about 2000 Chrysler LHS

2 Answers

How do you remove the starter?

Getting the screws undone from the starter was easy but the starter still won't come out. What all do you have to do to replace this starter?

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 316 Answers

You have to let the drivers side engine mount loose and jack up the motor about 3". It comes out easily this way. This is the only way to get it out.

Posted on Oct 02, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Take it to the shop

Posted on Apr 16, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hooked battery up wrong on 1992 explorer, stereo smoked and now the windshield wipers won't shut off. No blown fuses just popped the line circuit from starter relay to alternator. Replaced battery...


you must RUN the scanner/computer for easy diagnostic, and fix it.
Remember the electronic vehicle is very complicated, You can have some faulty: PCM+ignition coil+BCM+sensor+etc.
see the diagram attached.
God bless you773eec03-745a-4c7c-97a8-237db8219639.jpg

Jul 23, 2013 | Cars & Trucks

1 Answer

Engine won't start


Check to make sure you are getting voltage to the small post on the starter solenoid when the key is turned to the "crank" position. if so, check all of you connections on the battery cables. If your connections are all good, your cables are in good shape, and you still do not get the starter to crank, I would have the starter removed and tested.

Apr 21, 2013 | 2004 Toyota Tacoma

1 Answer

I need to replace the starter in my 1989 Toyota Supra Turbo and I'm not sure what all I need to take off before getting to the starter. Please help!!


First take off the battery cables of the battery (disconnect it) and for safety even take the battery out, underneath you might have the protection panels which are easy to remove (usually mounted with few screws), remove the leads on the back of the starter but make sure you remember how they were as the replacement starter needs to be wired same, unbolt the starter and take it out.

Aug 03, 2010 | 1989 Toyota Supra

1 Answer

What is the easiest way to remove the starter off a 97 nissan pick-up? there is an incredible lack of clearance to access the part and of course the bolts are extremely difficult to reach.


your telling me there is,!!!,,when it was built all the engine was put in from the bottom of the car so you will need a long reach socket and an elbow joint to get the starter bolts undone,,,them *** guys are only small you see? it not an easy job but its not impossible (only just nearly impossible!)

Feb 09, 2010 | 1997 Nissan Pickup

1 Answer

I need to replace my starter on my 1993 Ford F-150


Remove the drive belt remove the screws on the starter,replace the starter,re insert the belt and adjust screw to proper tension...easy

Jan 20, 2010 | 1988 Ford F 150

1 Answer

Driverside inside door won,t open the dr or even unlock the drs handle is pulled to release?


more likely the door handle mechanism is either broken or came undone, the only way to get to it and see what broken or came off is to remove the door cover panel, its not easy job and its time consuming if not mechanical incline although it something fairly simple to fix and repair. you may just have to replace inner door handle if it broken off from the linkage.

Oct 11, 2009 | 1998 Jaguar XK8

1 Answer

After the shop replaced my starter, I noticed that my car start shaking when it runs. What cost the problem?


Have you returned to place that did the repairs, as they may have knocked something off inadvertently, or left a mount undone or loose from getting access to starter.

Aug 28, 2009 | 2002 Toyota Camry

1 Answer

How do I remove the starter bolts if they will not come undone. I was able to get one of two out, however the second one will not come undone, even after spraying BREAK FREE on it


Are you in snow conditions with this vehicle? There is a product call PB screwloose Its a spray and it will penetrate, Try spraying at the other end where the threads come out of the block. You can also shock the bolt by hitting the bolt head with a hammer carefully. Try using a breaker bar or add a cheater pipe to your ratchet, Bolts do get corroded and difficult alot of times. If it breaks off ,the broken bolt can be drilled and easy outed. Just dont give up.

Jun 28, 2009 | 1997 Toyota Tacoma

2 Answers

How do I change the spark plugs on my 1999 SAAB 9-3? Do I have to lift the engine or is there an easy way to access the removal and installation of the plugs?


Remove the four screws from the ignition cassette located in the center of the valve cover. The sparkplugs are underneath it.

Mar 04, 2009 | 1999 Saab 9-5

1 Answer

Replace front speakers


its actually pretty easy. just remove the screws on the door panel. dont forget the one in the handle at the bottom. then remove the little triangle cover behind the mirror on the door. lightly pull from the bottom and the door panels pop clips will slowly come undone....once the door panel swings outwards pretty easily just lift up on the panel and it will come off....once its undone you can either remove the harness for the window switches and lock or just let the panel sit to the side still attached. either way works its just preference. then you just remove the speaker and replace with any 6.5inch you would like... reinstallation is the same..

Feb 18, 2009 | 2005 Scion xB

Not finding what you are looking for?
2000 Chrysler LHS Logo

Related Topics:

144 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...