Question about 1982 Chevrolet El Camino

1 Answer

Can i put 3.73 gears on a stock 1979 el camino differential

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 490 Answers

Yes you can

Posted on Apr 15, 2009

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What is the maximum speed of chevrolet el camino 350 hp 1978

That depends on what differential was put in the car. If it has 4:11 gears, it won't go very fast on top end but will have a good hole shot. If it has 3:08 gears, as is in stock, then it will do it's marked numbers with no problem.

Jul 10, 2017 | Chevrolet Cars & Trucks

1 Answer

How do I remove the upper A arm on a 1979 Chevrolet El Camino?

youll need to purchace what i call is a balljoint remover ( pickel fork )you many want to purchase both sizes. Having also a assortment of wrenches, a floor jack to set under the lower A arm and jack it up a bit. all this once the tire and rim have been removed. Because you are seperating the front spindel that holds the tire on from the upper A arm the floor jack is nessary. you may also put a jack stand under the framing of your El Camino to support that paticular side of your El Caminos front frame. once the jack stand and floor jack are placed properly your tire and rim can come off. You can see the that there is a nut with a cotter key on it. you remove the cotter key then the nut , after that you may remove or seperate the upper part of the spindle from your A arm. The coil spring is going to pop the A arm up and relieve the tension of the spring. Once that is completed remove the back side of the A arm which you can see, that it is secured on both sides. You'll figure the rest out once you tear into it.Hope this was helpful. as for instillation of the new one reverse what you did, by the way the coil spring will have to be compressed.

Jan 28, 2012 | 1982 Chevrolet El Camino

1 Answer

The blinkers dont work in my 83 el camino. i replaced the switch in the column and checked all fuses and relays. everythings good. hazzards work also horn. all of witch is in the turn signal switch. need...

Did you recently put wider than stock tires on your car? The wiring harness for the rear lights runs down the outside of the drivers side frame rail, wider tires will rub on the harness and cause damage to it and subsequent light failures.

Mar 27, 2010 | 1983 Chevrolet El Camino

1 Answer

Is it nesesrry to knoew the camshaft lift to time

No it is not, however a high performance cam will make it harder to adjust for smooth idle.

Mar 15, 2010 | 1987 Chevrolet El Camino

1 Answer

Want to replace a dash pad in 82 el camino need instructions to complete the installation

If you've never done a dash pad replacement before I would suggest getting an aftermarket cover77 88 EL CAMINO/MONTE CARLO FULLFACE NEW Dash Pad CAP, $87.99 ... (1) (Made 3 Ways) Sellers Choice New Dash Pad Cap for A 1977 1978 1979 1980 1981 1982 1983 ...
This is a snap on cover that covers your old one without it's removal,just paint it to match.Now you can get these from a lot of different places and I'm NOT recommending any business or company,just saying this is an easy way to get a nice looking dash without replacing it.

Oct 11, 2009 | 1982 Chevrolet El Camino

1 Answer

What other year models will have the same differential as a 1989 gmc truck 1/2 ton 4 wheel drive i looking to change out the whole rearend.

All the rear ends from that model run should fit size wise, and probably older as well as newer body styles. To be sure take a measurement from backing plate to backing plate to be sure. Also measure between your spring brackets. This has to be the same on you replacement rear end unless your are good at cutting and welding. Be sure you have the exact same gear ratio in the new rear end as the old. If the aluminum tag is missing, to be sure you will have to remove the cover and count the teeth on the crown gear and the pinion.This has to be exactly the same as the one you take out or you will need both rear ends in a 4x4. Most scrap yards stock rear ends by gear ratios, not dimensions. Hop this helps.

Jun 08, 2009 | 1982 Chevrolet El Camino

2 Answers

Car problems

i have the same problem with mine. I think it might be tha carburetor or that the rpm's might be to low. not sure. but those are my ideas.

Mar 22, 2009 | 1982 Chevrolet El Camino

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

137 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides