Question about 2000 Chrysler LHS

2 Answers

Where is the starter on a 2000 chrysler lhs?

Need to replace

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 316 Answers

The starter is under the drivers side of engine where it meets the bell housing you must unbolt the drivers side engine mount and jack up the engine about 3" to get the starter out.

Posted on Oct 02, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 5,158 Answers

I can't tell you what side it's on.... but it is where the motor joins to the transmission. if it is front wheel drive (the motor is sideways). look down about the middle of the engine where it joins the transmission.... that is your starter. you should be able to follow one of the large wires from the battery to it. speaking of which make sure you disconnect the battery before changing the starter.

Posted on Apr 15, 2009

  • Roberta Smith
    Roberta Smith Apr 15, 2009

    please take a moment to rate this solution.. thanks

×

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 75051 Answers

SOURCE: chrysler LHS won't start!!

Driver side at rear of engine next to oil pan goes into the bell housing.

Posted on Nov 24, 2008

localwonder
  • 6784 Answers

SOURCE: how do you replace the headlight bulb on a 2001 chrysler lhs.

This can be done buy popping the hood and removing the bulb from the rear of the headlight housing. don't screw with the housing because, its leveled for optimal sight range.

Posted on Jan 28, 2009

  • 226 Answers

SOURCE: Chrysler LHS Starter

The starter is located beneith the engine, near the transaxle and it is attatched to the engine by 3 bolts. You need to disconnect the battery, raise the car to get at it. The 3.3 and 3.5 engines take different starters. Rick

Posted on Apr 15, 2009

CMV9
  • 594 Answers

SOURCE: HOW TO REPLACE HEADLIGHTS ON

ATTN: NIKKICARROLL

here is how to replace the bulb in your vehicle


  1. Release the hood latch and open the hood.
  2. Remove the radiator closure panel sight shield as necessary to gain access to the headlamp.
  3. Remove the screws holding the headlamp module halves together.
  4. Separate the module halves.
  5. Disengage the wiring from the headlamp bulb.
  6. Remove the retaining ring from the back of the headlamp bulb.
  7. Pull the bulb from the lamp.
To install:
  1. Push the bulb into the lamp.
  2. Install the retaining ring to hold the bulb in the lamp.
  3. Engage the wire connector to the back of the headlamp bulb.
  4. Place the module into position on the vehicle.
  5. Install the screws to hold the module to the vehicle.
  6. Install the radiator closure panel sight shield.
  7. Check the headlamp alignment and operation.
88176gb1.gif Exploded view of the fog lamp with the bulb removed
Click to Enlarge

  1. Release the hood latch and open the hood.
  2. Remove the radiator closure panel sight shield as needed to gain access to the headlamps.
  3. Remove the screws holding the headlamp module halves together.
  4. Separate the halves.
  5. Remove the fog lamp wire connector cover.
  6. Disconnect the wires from the fog lamp bulb.
  7. Disengage the retainer clip holding the bulb to the fog lamp.
  8. Remove the bulb from the fog lamp.
To install:
  1. Place the bulb into position in the fog lamp.
  2. Engage the retainer clip to hold the bulb to the fog lamp assembly.
  3. Attach the wire connectors to the fog lamp bulb.
  4. Install the fog lamp wires connector cover.
  5. Place the module halves together.
  6. Install the screws to hold the headlamp module halves together.
  7. Install the radiator closure panel sight shield.
  8. Verify the fog lamp operation and alignment

ATTN: WDSNEED1

Removal & Installation 88176g87.gif Remove the screws retaining the headlamp module to the mount adapter
Click to Enlarge

  1. Release the hood latch and open the hood.
  2. Remove the radiator closure panel sight shield as necessary to gain access to the headlamp fasteners.
  3. Remove the screws holding the headlamp module to the mount adapter.
  4. Separate the headlamp module from the mount adapter.
  5. Disengage the wiring from the headlamp and foglamp.
  6. Remove the headlamp from the vehicle.
To install:
  1. Attach the wires to the headlamp and foglamp assembly.
  2. Place the headlamp module into position on the mount adapter.
  3. Install the screws to hold the headlamp module to the mount adapter.
  4. Install the radiator closure panel sight shield.
  5. Check the headlamp alignment and operation.

Posted on Apr 16, 2009

  • 4 Answers

SOURCE: chrysler LHS won't start!!

the starter is on the right side of the motor down below the the air intake bolted to the transmission three bolts and it comes off

Posted on Jun 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2000 chrysler lhs and i need a diagram of the ignition coil pack as in a firing order


For just a few dollars you can get the "Haynes Automotive" manual for the L.H.S. that will have what you need, plus so much more. It is written for the average person and has all the wiring diagrams and even walks you through the engine rebuild. If you love your L.H.S. like I do mine, then it is worth the tiny, tiny investment. I would dig mine out for you but this is a better solution. You can get it online, or at ANY decent Auto Parts store. If you REALLY want me to dig mine out, hit me back and I will.

Mar 19, 2014 | 2000 Chrysler LHS

1 Answer

I need to know the location of a starter for a Chrysler lhs?


Melco starter being used with the 3.5L engine,and a Nippondenso for the 3.3L. Both follow the same step-by-step procedure. By inference it sounds like there is only one wrinkle in that the procedure is as follows:
Disconnect the battery (-) cable
Raise the vehicle
Do not remove the wiring from the starter at this time, first:
Remove three bolts attaching starter motor to engine
Remove the starter/starter solenoid as an assembly from the engine:
Position the assembly so as to gain access to the connectors
Remove the battery cable nut, field terminal nut, and push-on solenoid wire connector and the other wires
Remove the starter.
Installation is the reverse. Clean the cable and wire connectors before reassembly.
So other than that, neither the Chrysler nor the Haynes speak of any unusual steps in the process.
Let me know if you find otherwise so I can pass the info on to other owners, please.
I haven't done this one myself, so it is limited advice I can offer. The figures show there to be a "cover" mounted between the starter motor and the engine (it looks like a gasket) and the top bolt hole contains a "starter shield retention sleeve".
So you might want to familiarize yourself with those at the time you finally remove the motor so you don't loose track of those small parts.
On the Melco it shows that the starter solenoid can be replaced separately, but doesn't show that for the Nipppondenso.

Your Chrysler Lhs starter is the primary device that will get your ride going, initiating the operation of the power plant so you can go on your way. In case your Chrysler Lhs has hassle getting started, you probably need to swap out the old starter to restore ideal ignition performance.

You're likely never going anyplace if ever you cannot get your vehicle torun as the starter in your Chrysler Lhs is damaged. The most effective remedy when it comes to a broken starter is to get a replacement and subsequently install it. You're going to love superb ignition on your Chrysler Lhs because of a fresh alternate mounted. You can certainly purchase either new choices or choose to order remanufactured variants instead. A lot of Chrysler Lhs starters out there are offered in sets or are for sale separately. It is advisable to shop for direct-fit or OE replacement parts so you'll be able to install them with no problem.

To locate a Chrysler Lhs starter that's going to provide outstanding functionality for a while and would not ruin your funds, do not be reluctant to shop with us. We stock components coming from companies like Denso, AC Delco, and Motorcraft so you're certain to acquire parts that will not let you down. All you have to do to avail of reliable car parts is to look into the Parts Train catalog and search for the right item that satisfies your requirements.

Nov 22, 2011 | 1999 Chrysler LHS

1 Answer

Chrysler LHS won't start!!


the starter is on the right side of the motor down below the the air intake bolted to the transmission three bolts and it comes off

May 31, 2009 | 1999 Chrysler LHS

1 Answer

Replaced cracked radiator in 2000 Chrysler LHS but car still overheating. What could be the problem?


fix the radiator first.because coolant temperature sensor need to be in antifreeze.when antifreeze get up to 190 degrees. the coolant sensor act as a thermostat.it resistance decrease then the pcm will command cooling fans to run.if antifreeze low the coolant temperature sensor not going to work. engine is going to over heat.

May 29, 2009 | 2000 Chrysler LHS

2 Answers

Replaced cracked radiator in 2000 Chrysler LHS but car still overheating. What could be the problem?


I had the same problem. My Chrysler LHS kept overheating. I had the thermostat changed out first and it didn't help. Then I had the water pump changed out and still did no good. Then changed out the radiator, still overheated. Come to find out the people that changed my thermostat put it in backwards. Evidently, the thermostats for these cars look different from all the others and people are not sure how to put them in. I took mine to a Chrysler dealer and they fixed it for me.

Apr 15, 2009 | 2000 Chrysler LHS

1 Answer

Chrysler LHS Starter


The starter is located beneith the engine, near the transaxle and it is attatched to the engine by 3 bolts. You need to disconnect the battery, raise the car to get at it. The 3.3 and 3.5 engines take different starters. Rick

Mar 15, 2009 | 1995 Chrysler LHS

2 Answers

How do you replace the headlight bulb on a 2001 chrysler lhs.


This can be done buy popping the hood and removing the bulb from the rear of the headlight housing. don't screw with the housing because, its leveled for optimal sight range.

Jan 28, 2009 | 2000 Chrysler LHS

Not finding what you are looking for?
2000 Chrysler LHS Logo

408 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...