Question about 1997 Mazda Millenia

1 Answer

Crankshaft Position Sensor On A 1997 Mazda Millenia

Is it possible to replace the Crankshaft Position Sensor without removing any drive belts?? If so, how?? If not, is there an easy way to remove the drive belts?? My manual doesn't quite explain how to do so..

Posted by on

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 28 Answers

No way you need to open the timing belt to get to it , Mazda sucks.

Posted on Aug 20, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the crankshaft position sensor located on the 2002 Mitsubishi Montero sport xls 3.5 truck.


Hi David, The link below is how to test the crank sensor (1997-2004 3.0l Montero, Hope this helps......CHEERS
http://easyautodiagnostics.com/mitsubishi/3.0L/crankshaft-position-sensor-test-1#3
The crankshaft position (CKP) sensor is located behind the timing belt... but testing it is done without removing the timing belt or its components. This is due to the fact that the crank sensor's connector is located on top of the engine and in plain view (next to the ignition control module). In the photo below, the orange arrow points to the location of the crankshaft position sensor connectors (photo applies to: 3.0L 1997-2004 Montero Sport).

Mar 31, 2016 | Mitsubishi Cars & Trucks

1 Answer

Is there a belt I can put on my 1997 Mazda Millenia that will bypass my AC compressor all together?


-It's possible. If the compressor is not on the way you can use a short belt.


mai

Oct 10, 2013 | 1997 Mazda Millenia

1 Answer

Crank shaft seal leaking oil


you have to replace front crankshaft seal meaning you have to remove crankshaft pulley.you have to remove timing belt and remove timing belt sprocket and key.

Apr 09, 2013 | 1999 Mazda Millenia

1 Answer

How to position the timing belt crank shafts of 1997 mazda mpv


Raise and support the vehicle on jack stands. Remove the wheel on the passenger side of the vehicle using the drive ratchet and a socket. Remove the passenger side splash shield, using the drive ratchet and a 10mm socket. 2 Remove the accessory belt(s), using a wrench to loosen the tension. Unscrew the bolt from the crankshaft pulley, using the drive ratchet and a socket. Slide the crankshaft pulley and the timing belt guide washer directly behind it off the crankshaft.3 Remove all the 10mm bolts in the top and bottom timing belt covers. Remove the covers. The drive ratchet and a 10mm socket works well for this. 4 Push the crankshaft pulley on the crankshaft just enough to engage the keyway. Turn the crankshaft pulley clockwise until the timing mark on the top camshaft sprocket, which is marked with a line on the sprocket with a number 1 next to it, is lined up with the pointer straight up on top of the cover to the rear of the sprocket. Once the top mark is lined up, the crankshaft pulley's semi-circle mark should be lined up with the triangular pointer on the block. The marks on the crankshaft pulley should be straight up and the keyway should also be straight up. Remove the crankshaft pulley. 5 Loosen the tensioner bolt with a wrench, pull the tensioner to the left, away from the belt and loosely tighten the bolt to hold it in place. Remove the timing belt. 6 Install the timing belt counter-clockwise starting at the crankshaft pulley and move upward over the outside the water pump, on the inside the guide pulley and over the top of the camshaft, ending on the inside the tensioner. The main thing when installing a timing belt is to ensure the belt is as tight as possible opposite the tensioner. Get the belt tight between the crank sprocket and the cam sprocket so the tensioner can take out all the slack without moving the timing marks.7 Loosen the tensioner bolt and allow the tensioner to apply pressure to the belt. Use your hand to apply a slight pressure to the tensioner toward the belt and tighten the tensioner bolt. Check the belt tension to ensure it is not too tight or too loose. Check the timing marks again to ensure they still align. If the timing marks are not lined up, loosen the tensioner, move it back and repeat the last procedure over again until the belt is tensioned properly with no misalignment of the timing marks. 8 Install the crankshaft pulley temporarily and turn the pulley two complete revolutions, once again aligning the mark on the crankshaft pulley. Ensure the timing mark is still lined up perfectly on the camshaft sprocket. Reinstall the remaining parts in reverse order of removal

Oct 14, 2011 | 1997 Mazda MPV

1 Answer

WHAT PARTS DO YOU NEED TO TAKE OFF TO CHANGE THE CRANKSHAFT POSITION SENSOR


The splsh gaurds under the car then you should be able to see the sensor its right behind the lower belt pully the hormonic balancer Its easy to replace and will make a world of differance in how the vehicle runs if its bad

Nov 11, 2010 | 2002 Mazda Millenia

1 Answer

How to replace the crankshaft positioning sensor for a 2002 mazda millennium


Welcome to FIxYa.com


CRANKSHAFT POSITION - SENSOR REPLACEMENT


1. Disconnect the negative battery cable.

2. Remove the idler pulley bracket.

3. Remove the dipstick pipe.

4. Remove the CKP sensor

5. Install in the reverse order of removal.

6. Adjust the drive belt deflection.

leedavidian_52.png


Thank you for using FixYa.com

Regards, Lee Davidian

Nov 09, 2010 | Mazda Millenia Cars & Trucks

2 Answers

Mazda Millenia 1997...flashing hold light when driving car...car changes gear like there is no clutch


you mean check engine light flashing??? if so then the engine is skipping and the lack of power putput will cause the trans to change gears constantly. is this the issue you describe?

Sep 03, 2009 | 1997 Mazda Millenia

1 Answer

1995 mazda millenia no spark but removed timing tensioner b4


check crank/cam sensors. could have been damaged when the tens.was broken.

Jun 11, 2009 | 1997 Mazda Millenia

1 Answer

1997 Mazda Millenia, Changed Almost Everything, Still No Spark..


check the pcm .get it scan make sure your pcm is working.also check ignition coils.

Apr 20, 2009 | 1997 Mazda Millenia

Not finding what you are looking for?
1997 Mazda Millenia Logo

346 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8195 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...