Question about 1999 Plymouth Voyager

1 Answer

Shift Solenoid c Where and how to replace in A 99 plymouth Voyager

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Plymouth Master
  • 599 Answers

The c solenoid is located in the transmission,valve body you have to drop the transmission pan and locate the solenoid, this is a job best suited to a transmission shop,or some one with a lift.

Posted on Apr 15, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1998 plymouth voyager , transmission will not shift past second gear,


Buy an ATSG Transaxle Manual

They are avail on their web site or at
a local trans supply house where the local
shops go for parts

Mar 31, 2014 | 1998 Plymouth Grand Voyager

1 Answer

Transmission will not shift into overdrive


sound like a stuck open or closed pressure control shift solenoid and also your 3rd and 4th shift solenoid

Dec 10, 2012 | 1994 Plymouth Voyager

1 Answer

1998 PLYMOUTH Voyager 2.4 3 speed auto Just started doing this: stays in first gear until about 28 mph.


Sounds like a valve body problem, or shift solenoid inside the transmission. Sounds like it is sticking. Check fluid make sure it is not brown which means it is burnt, and make sure there is plenty of fluid but not overfilled.

Oct 10, 2010 | 1998 Plymouth Voyager

1 Answer

1997 plymouth grand voyager cruise control problems


Try doing a "Brain Kill" on the van. Disconnect both battery terminals, and (MAKE SURE THEY ARE NOT CONNECTED TO THE BATTERY!!!!!) touch and hold them together for at least 10 seconds. Mopars hold onto their faults, even after the repairs. Huge problem for transmission shops, but that's another topic. My 99 Dakota had the Speed Sensor fail, and it wouldn't shift until I "Killed" the ECM and BCM's memories.

Good Luck!!!

May 22, 2010 | 1997 Plymouth Grand Voyager

2 Answers

The transmission will not shift gears and the


Hi:
This same thing happened to my daughter,s car, and it ended up being fixed with a transmission speed sensor. This sensor not only runs the speedometer, it helps tell the transmission when to shift too.

Nov 05, 2009 | 1999 Plymouth Grand Voyager

1 Answer

I have a 98 plymouth grand voyager with a 3.3l 4 speed transmission. My van goes into limp mode after a couple minutes of driving. My question is how do I determine if my shift solenoid or my tcm is the...


THERE MUST BE SOME FAULT CODES STORED IN TCM..WHEN A FAULT OCCURS,THE TCM SHUTS THE POWER FEED OFF TO THE SHIFT SOLENOIDS IN THE SOLENOID PACK SO ALL YOU HAVE IS SECOND GEAR(LIMP MODE)..IS YOUR SPEEDOMETER WORKING?IF NOT IT MAY BE THE OUTPUT SPEED SENSOR IS BAD..YOU SHOULD GET TCM SCANNED FOR FAULT CODES..I HOPE THIS HELPS

Sep 17, 2009 | 1998 Plymouth Grand Voyager

1 Answer

Voyager transmission problem


Sounds like you need a solenoid pack to start, and possibly a service. If the tranny is not slipping, the solenoid pack is stuck and not tell it to shift up. Could possibly be a TCM, but not as likely.

May 30, 2009 | 1999 Plymouth Grand Voyager

2 Answers

Transmission problem


There are only a few connectors that need plugged in. The first one is the solenoid pack which has eight wires and a bolt that goes through the connector. then the range sensor which will be located by the shifter shaft, will have either round or flat spade like pins. The wiring is the same only difference is the connnector; you may need to get a matching plug if the new one doesn't match your vehicle's harness. Then there are two speed sensor plugs that are small simple push in plugs that have two wires each. You may or may not have a crank sensor to plug in, if you do it will plug in kind of on top of the bell housing more towards the firewall. That should be it.

Jun 16, 2008 | 1999 Plymouth Voyager

Not finding what you are looking for?
1999 Plymouth Voyager Logo

Related Topics:

461 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...