Question about 1996 Mercedes-Benz C-Class

1 Answer

Wipers not working in the 1 2 3 position merc c220 2006

My wipers only work when i press the windscreen spray button they will not work when i switch them in the 1 2or 3 position

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 408 Answers

Hello,seem your combination switch have problem,remove your under dash,maybe poor connection on wiring or your combi. switch defective,ty

Posted on Apr 16, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can the wiper linkage cause the wipers to park vertical. Wipers work fine on all settings. Tried repositioning the wiper arms but it didn't work


normally if the wiper arms park in the wrong place , it is the fitting of the wiper arms on the pivot that is wrong
try pulling the wipers back off the windscreen , run them through a cycle and then switch off normally
that will be the park position in the motor gear box
then remove each arm from the pivot and re- position it about 1" from the bottom of the screen
that will be the parked position for the wiper blades
having done that then again pull the arms back of the screen and cycle as if wiping the screen
switch of and see where the arms now park on the screen
if it is close to where you set them then that is the park position
next run the wipers a cycle and see if at full movement one arm puts the blade over the edge of the screen or hits the edge
switch off and re-position that arm closer to the bottom of the windscreen
it is time consuming but the only way to park wipers properly as there is no master spline to set in the correct position
If they park any where after this exercise ,replace the wiper unit as there is a problem in the contacts in the motor box.

Sep 14, 2015 | Cars & Trucks

1 Answer

Windscreen wipers not working


Wiper arm is loose at pivot. Take caps off at pivot and run motor to rest position. Move wiper arms to rest position and secure nuts.

Mar 01, 2015 | 2008 Audi A3 S Line Hatchback

2 Answers

Erratic windscreen wiper action


sounds like the wiper control itself is playing up

Feb 27, 2014 | 2001 Nissan Micra

1 Answer

Rear windscreen wash not working on Skoda Octavia


Remove cover from rear wiper arm (it is covering the wiper arm nut) gently ease off the plastic moulding in the middle of the nut try squirters if water is coming out unblock the water jet holes in the plastic moulding

Jun 29, 2012 | Skoda Octavia Cars & Trucks

1 Answer

Windscreen wipers not working on my vw passat 2005 '05' but washers are working!


First time you must diagnose why windscreen wipers going slow and/or stopping.
If the windscreen wipers fuse is good:
In order to find out the cause of wipers stopping you can try follows:

1. Carefully extract the wiper arms from their axles (two pieces). In some cases you need to use an extracting tool. Heed of the windscreen !!!
2. Disassemble the plastic covers from the bottom of the windscreen.
3. With the bonnet up you can start the engine, (transmission in "N" or "P" position and parking brake on). Now you must switch on the control lever of the wipers, and go to the engine compartment. If the wiper motor runs let the wiper motor running for a few minutes and switch off. Go to the step 4. If the wiper motor do not runs you must check first the electrical feeding of the motor. It is necessary to unscrew three bolts of the mechanism and disconnect the electrical coupling (difficult assurance). If the electrical feeding is OK you must replace the motor - steps 5, 6, 7. If not you must check electrical connections, the control switch of wipers and electric cables.
4. Now you must check the two bearings of wiper mechanism with your hand. In the most cases the left bearing is out of order (is very hot). This is the most encounter fault of the wipers.
5. For have enough space to manipulation the wiper motor together with their mechanism you must extract the plastic cover of the engine computer box, and extract also the box screws. Then you can move slowly the engine computer box, just for a few milimeters.
6. You must disconnect the electrical coupling of the motor (difficult assurance), unscrew three bolts of the mechanism and extract together with the motor. You must move them slowly between windscreen and engine computer box until the wiper motor go out together with the mechanism. This is the most difficult operation!
7. Now you can repair the bearings, replace entire wiper mechanism or replace the wiper motor. It is not very simply, but it works.
Heed of the windscreen !!!
Refit all in reverse order.

Apr 14, 2011 | 2005 Volkswagen Passat

1 Answer

Wiper Blades not working properly


First you must diagnose why windscreen wipers going slow and/or stopping.
In order to find out the cause of wipers stopping you can try follows: 1. Carefully extract the wiper arms from their axles (two pieces). In some cases you need to use an extracting tool. Heed of the windscreen !!! 2. Disassemble the plastic covers from the bottom of the windscreen. 3. With the bonnet up you can start the engine, (transmission in "N" or "P" position and parking brake on). Now you must switch on the control lever of the wipers, and go to the engine compartment. If the wiper motor runs let the wiper motor running for a few minutes and switch off. Go to the step 4. If the wiper motor do not runs you must check first the electrical feeding of the motor. It is necessary to unscrew three bolts of the mechanism and disconnect the electrical coupling (difficult assurance). If the electrical feeding is OK you must replace the motor - steps 5, 6, 7. If not you must check electrical connections, the control switch of wipers and electric cables. 4. Now you must check the two bearings of wiper mechanism with your hand. In the most cases the left bearing is out of order (is very hot). This is the most encounter fault of the wipers running at Audi. 5. For have enough space to manipulation the wiper motor together with their mechanism you must extract the plastic cover of the engine computer box, and extract also the box screws. Then you can move slowly the engine computer box, just for a few milimeters. 6. You must disconnect the electrical coupling of the motor (difficult assurance), unscrew three bolts of the mechanism and extract together with the motor. You must move them slowly between windscreen and engine computer box until the wiper motor go out together with the mechanism. This is the most difficult operation! 7. Now you can repair the bearings, replace entire wiper mechanism or replace the wiper motor. It is not very simply, but it works.
Heed of the windscreen !!!
Refit all in reverse order.

Please rate my response. Thanks!

May 25, 2010 | 2004 Audi A4

1 Answer

My front wipers arent working, could it just be the fuse? if so which fuse do i change as the list only has my rear wiper on it.


Fuse nr.31, F31, (25A) = Windscreen wipers
This fuse is placed on fuse box / relay plate engine bay 1, under bonnet in engine compartment area!

If the fuse F31 is OK.
You must diagnose why windscreen wipers going slow and/or stopping.
In order to find out the cause of wipers stopping you can try follows:
1. Carefully extract the wiper arms from their axles (two pieces). In some cases you need to use an extracting tool. Heed of the windscreen !!!
2. Disassemble the plastic covers from the bottom of the windscreen.
3. With the bonnet up you can start the engine, (transmission in "N" or "P" position and parking brake on). Now you must switch on the control lever of the wipers, and go to the engine compartment. If the wiper motor runs let the wiper motor running for a few minutes and switch off. Go to the step 4. If the wiper motor do not runs you must check first the electrical feeding of the motor. It is necessary to unscrew three bolts of the mechanism and disconnect the electrical coupling (difficult assurance). If the electrical feeding is OK you must replace the motor - steps 5, 6, 7. If not you must check electrical connections, the control switch of wipers and electric cables.
4. Now you must check the two bearings of wiper mechanism with your hand. In the most cases the left bearing is out of order (is very hot). This is the most encounter fault of the wipers running at Audi.
5. For have enough space to manipulation the wiper motor together with their mechanism you must extract the plastic cover of the engine computer box, and extract also the box screws. Then you can move slowly the engine computer box, just for a few milimeters.
6. You must disconnect the electrical coupling of the motor (difficult assurance), unscrew three bolts of the mechanism and extract together with the motor. You must move them slowly between windscreen and engine computer box until the wiper motor go out together with the mechanism. This is the most difficult operation!
7. Now you can repair the bearings, replace entire wiper mechanism or replace the wiper motor. It is not very simply, but it works.
Heed of the windscreen !!!
Refit all in reverse order.

Jan 13, 2010 | 2006 Audi A3

Not finding what you are looking for?
1996 Mercedes-Benz C-Class Logo

428 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76673 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

166 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...