Question about 1990 Toyota 4Runner

1 Answer

How to change the outer cv boots on a 1990 toyota surf

Posted by on

  • maurergeorge May 25, 2009

    how to disassemble front hub to replace boot

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

You pull the enitre wheel assembly out to be able to slip the entire broken cv boot out. Look in the manual on how to pull the axle out.
This will be the best write youll find for this
http://www.4x4wire.com/toyota/maintenance/cv_axle/

Posted on Apr 23, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Front outer cv boot does not fit axle. 2006 Impala 3.9.


You should be able to get a universal CV boot. Obviously, you would have to check the dimensions before buying it.

Have a look on Ebay. A supplier of CV boots should be able to sort one out for you.

impala cv boot

Mar 29, 2016 | 2006 Chevrolet Impala

1 Answer

How much for fixng outer cv boots leaking


It costs:
CV Joint boot cost + Graphite or silicone grease + Transmission oil (less than a Liter) + Service charges.
It is hard to mention the exact price.

Jul 31, 2014 | Toyota Corolla Cars & Trucks

1 Answer

How to change outer cv boot


loosen drive shaft nut, You unbolt lower control arm pull end shaft from hub remove clamps from both endsand slide boot of or cut of and fitting is reversed proccedure

Apr 08, 2012 | 1990 Mitsubishi Sigma

3 Answers

When replacing a outer C.V joint boot , do you


you can replace just the outter but you may want to replace the whole axle alot easier

Jan 17, 2010 | 1993 Ford Festiva

1 Answer

How do I replace cv boot on a buick park ave


The boot you need to replace is call OUTER CV BOOT.

The quickest way to inspect is to drive it in low speed (UNDER 10 mph) tight left and right turns.

If you hear clicking sound then the CV shaft is bad.

It's also depending on how long the CV boot been crack.

===
If you decide to go ahead on the job then please observe safety and use jack stands to fully support the front end.

Remove wheel,cotter pin,retainer cap and larger axle nut.

Make alignments markings on the strut tower and steering mount so your front end will able to put back to alignment.

You will need an able body to do the following.

Remove the large lower strut bolts and swing the strut off the CV.

DO NOT ROCK THE CAR!!!

Clean off the outer CV.

Install boot,grease and the two bands.

Line up the strut and steering yoke marks

repack bearings,lock nut,cap,cotter pin,wheel.


Drive the car in low speed for 1 miles with tight turns.

Do a quick inspection to make sure the CV boot is sitting perfectly on the CV.

















Nov 16, 2009 | 1990 Buick Electra

1 Answer

Want to change CV boot in 1990 Toyota 4Runner manual 4WD


You can buy a whole reman axle for around 60.oo....dont mess with a boot..Lee

Sep 15, 2009 | 1990 Toyota 4Runner

1 Answer

Trying to get the bearing off of the cv axle 1994 camry


I think you mean cv joint. If so, a new axle cost $59. You are doing alot of extra work and the joints could be damaged. The outer joint comes off, but it takes a large hammer. The inner joint usually has an inboard ring clip that you pop out with a screwdriver.

Mar 25, 2009 | 1994 Toyota Camry

2 Answers

97 toyota celica outer cv boot replacement passenger side


have you undone the main hub bolt, if yes, there could be two different items holding the cv joint on, one is a small circlip in the joint end, or the other is just like an expanding metal ring again only small. what i had to do to change my one was take the driveshaft out (easier to see whats there) then gently (rubber hammer) hit the CV joint it should then fall off to allow you to change the CV joint. I spent over an hour trying to get the metal ring off, then after taking driveshaft off it was changed and back on in ten mins. Or you can go to a motor factors or similar and get a boot puller, my opinion hammer works better lol

Jan 25, 2009 | 1997 Toyota Celica

1 Answer

Replacing outer cv boot


go get a univeral boot at the store, cut the old one off with a knife, and use pliers to remove the band, and put the new ones on.

Nov 26, 2008 | 1989 Toyota Camry

Not finding what you are looking for?
1990 Toyota 4Runner Logo

Related Topics:

439 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...