Question about Toyota Xtracab

1 Answer

Hiace Wiper Motor Intermittent and dragging

Maybe it's just the contacts, but my front wiper motor stalls and always cycles slower than it should. I want to replace it, any tips on getting the dashboard out to get at it?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 11,896 Answers

Not the dash. You u can pull the vent system off under the wiper shaft. You can than get to wiper motor from there.

Posted on Apr 15, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ford escape 2006 rear wiper innoperative


Do you know how these wipers Work / what controls them ? Do you know what a smart junction box is ?
Rear Window Wiper Operation
The rear wiper motor is controlled by the SJB. The SJB supplies power to the rear wiper motor from the integrated rear wiper relay. The SJB will activate the relay when all of the following conditions are met:
  • Ignition switch is in the ON position
  • Liftgate glass and liftgate are closed
  • Multifunction switch is in the ON or INTERMITTENT position
The SJB also supplies voltage to the rear wiper motor from SJB fuse 21 (10A) when the ignition switch is in the ON position. This power feed is used to continue the wipe cycle when the multifunction switch is turned to the OFF position. The SJB receives inputs from the multifunction switch that applies ground to the low speed wipe input or applies ground to the intermittent wipe input. When either of these circuits are grounded, the SJB activates the integrated rear wiper relay and power is supplied to the rear wiper motor to move the rear wiper motor from the PARK position. An internal switch in the rear wiper motor then moves to the RUN position which connects the accessory relay power to the rear wiper motor. When the rear wiper motor returns to the PARK position, the internal switch in the rear wiper motor moves back to the PARK position. If the multifunction switch is in the ON position, the rear wiper relay is still activated, power is supplied to the rear wiper motor, and the wipe cycle starts again. If the multifunction switch is in the INTERMITTENT position, the rear wiper relay does not activate until the predetermined dwell time has elapsed, at which time the SJB activates the rear wiper relay and the wipe cycle starts again.

Do you know what DTC'S - diagnostic trouble codes are ?
Smart Junction Box (SJB) Diagnostic Trouble Code (DTC) Index DTC Description Source Action B1244 Wiper Rear Motor Run Relay Coil Circuit Failure SJB If the rear wiper is inoperative, Go To Pinpoint Test B . If the rear wiper is always ON, Go To Pinpoint Test D . B1245 Wiper Rear Motor Run Relay Coil Circuit Short to Battery SJB Go To Pinpoint Test B . B1614 Wiper Rear Mode Select Switch Circuit Failure SJB Go To Pinpoint Test D .
Did you have it checked for DTC'S ?

Jan 17, 2018 | Ford Cars & Trucks

1 Answer

I have a 2009 gmc sierra, where is the wiper relay location.


The PCB wiper relays are soldered directly to circuit board inside the under hood fuse box.
The windshield wiper/washer switch signal circuits are inputs to the body control module (BCM) and the BCM controls wiper motor low speed operation, washer pump and high speed operation. The windshield wiper/washer switch is provided a low reference from the BCM and each of the switch signal circuits is supplied 12 volts through a resistor and monitored within the BCM. During LOW or INTERMITTENT operation the wiper switch low signal circuit is closed to the low reference circuit through a series of resistors within the switch assembly and the signal circuit voltage monitored by the BCM will depend on the switch contact location to the resistor assembly. During HIGH or WASH operation the high and wash switch signal circuits are closed directly to the low reference circuit within the switch assembly and nearly all the signal circuit voltage will be dropped across the BCM resistors. The BCM controls the wiper motor through the WIPER CONTROL PCB Relay and the WIPER SPEED PCB Relay. During any wiper motor function that uses low speed the BCM supplies the voltage to energize the WIPER CONTROL PCB Relay and battery voltage will be supplied from the WIPER CONTROL PCB Relay through the de-energized WIPER SPEED PCB Relay to the wiper motor low speed control circuit. During high speed wiper motor operation the WIPER CONTROL PCB Relay is energized as in low speed and the BCM provides a ground to energize the WIPER SPEED PCB Relay and the battery voltage is supplied to the wiper motor high speed control circuit. Wiper motor park operation is controlled by the BCM using an input from the park switch within the wiper motor assembly. The BCM supplies the park switch signal circuit 12 volts through a resistor then monitors the circuit. Whenever the wiper motor is out of the park position the park switch signal circuit is closed to ground and nearly all the signal circuit voltage will be dropped across the BCM resistor. When the wiper switch is turned to the OFF position while the wiper motor is somewhere in mid-cycle, the BCM will continue to operate the motor until the wipers reach the park position. If the ignition is turned OFF while the wipers are in mid-cycle, the wipers will stop immediately where they are and the BCM will park the wipers the next time the ignition is cycled ON.

DTC B3715 02: Front Wiper Relay Drive Circuit Short to Ground
DTC B3875 00: Wiper High Speed Relay Circuit
DTC B3922 00: Front Wiper Function Select Circuit
Have it checked for DTC'S - diagnostic trouble codes .

The body control module (BCM) controls the wiper motor based on input from the windshield wiper washer switch. The BCM monitors the wiper washer switch through three separate signal circuits and a ground circuit. The windshield wiper switch high signal circuit is used to determine high speed wiper operation, the windshield wiper switch low signal is used to determine low speed, intermittent, and mist operation through the use of a resistor ladder, and windshield washer switch signal circuit is used to determine washer operation.
The BCM controls the windshield wiper motor through two output controls, controlling two relays which determine the desired wiper speed, high or low.
Your best bet , take your vehicle to a qualified repair shop or dealer . Hooking up a factory scan tool to see what the wiper switch inputs to the BCM are correct and outputs to relays are good .

Feb 11, 2017 | GMC Cars & Trucks

1 Answer

2005 ford escape wiper and washer has no power. cant hear it engage when on but was working a week ago. how can i troubleshoot it and find the fuse


Hi Justin , Do you know what a SJB - smart junction box is and where it is located on you escape ?
Windshield Wiper Operation
The smart junction box (SJB) supplies power to the multifunction switch from the SJB fuse 25 (20A) when the ignition switch is in the ON or ACC position. The multifunction switch supplies power to the windshield wiper motor for the HIGH or LOW/INTERMITTENT input, depending on the multifunction switch position selected. The SJB also supplies power directly to the windshield wiper motor from fuse 25 (20A) when the ignition switch is in the ON or ACC position for RUN/PARK operation. When the multifunction switch is in the LOW, HIGH, or INTERMITTENT position, power is supplied to the windshield wiper motor, which moves the wipers off the park position. Once the wipers are off the park position, an internal switch in the windshield wiper motor switches to the run/park position which directs power to the wiper switch then back to the wiper motor. This maintains power to the windshield wiper motor to complete the wipe cycle. When the cycle is complete, the internal switch in the windshield wiper motor switches back to the park position. If the multifunction switch is in the LOW or HIGH position, power is supplied from the multifunction switch and another wipe cycle starts. If the multifunction switch is in the INTERMITTENT position, the windshield wipers remain parked until the internal relay in the multifunction switch supplies power to the windshield wiper motor. The internal relay supplies power after a time delay that is determined by the 1 of 9 intermittent switch settings.

Jan 08, 2017 | 2005 Ford Escape

1 Answer

Why is my windshield wipers running in the off position, it's like they are running in the intermittent position, but it's in the off position.


When the windshield wiper / washer switch is turned to the OFF position while the wiper motor is somewhere in mid-cycle, the wiper motor module will continue to operate the wiper motor until the wipers reach the park position. If the ignition is turned off while the wipers are in mid-cycle, the wipers will stop immediately where they are. The wipers will park the next time the ignition is cycled to the ON position.

Schematic Reference: Wiper/Washer Schematics


1

Did you review the Wiper/Washer System Description and Operation and perform the necessary inspections?
Go to Step 2
Go to Symptoms - Wiper/Washer Systems

2

  1. Turn the ignition ON.
  2. Turn the windshield wiper/washer switch OFF.
Are the windshield wipers always on?
Go to Step 3
Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems

3

Disconnect the windshield wiper/washer switch connector.
Are the windshield wipers always on?
Go to Step 4 if yes
Go to Step 7 if no

4

  1. Disconnect the windshield wiper motor connector.
  2. Test the windshield wiper switch signal 1 circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 5

5

Test the windshield wiper switch signal 2 circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 6

6

Test the windshield wiper motor high speed circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 9

7

Inspect for poor connections at the windshield wiper/washer switch. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 8

8

Replace the windshield wiper/washer switch. Refer to Windshield Wiper and Washer Switch Replacement - On Vehicle in Steering Wheel and Column.
Is the repair complete?
Go to Step 11
--

9

Inspect for poor connections at the windshield wiper motor. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 10

10

Replace the windshield wiper motor. Refer to Windshield Wiper Motor Replacement .
Is the repair complete?
Go to Step 11
--

11

Operate the system in order to verify the repair.
Did you correct the condition?
The Wiper / Washer System consists of the following components:
?€¢
Windshield wiper / washer switch


?€¢
Windshield wiper system module / motor


?€¢
Windshield washer fluid pump


?€¢
Windshield washer fluid level switch


?€¢
Instrument panel cluster (IPC)


?€¢
ACC 15-amp fuse


?€¢
WSW 30-amp fuse

Jan 04, 2016 | 2002 Pontiac Bonneville

2 Answers

I have a 1998 jeep cherokee. The front wipers are not working. Can you plese help me solve this problem


Check the fuses first. If the fuse keeps blowing, it could be binding linkage. It could be the wiper switch. Make sure power is getting to the wiper motor.
Also there is a contact in the wiring of the wiper motor that parks the wiper blades even if you shut off the wiper switch mid cycle. If this contact is bad, the wipers won't work.

Feb 05, 2015 | 1998 Jeep Grand Cherokee

1 Answer

Wipers not working


A little trick to try is untightening the mounting bolts of the wiper motor and then retightening. Sometimes its a matter of re-establishing a good ground.

The wiper parking problem is an internal wiper motor function. Some electric contacts are suppose to derail the motor and it is suppose to cycle into the locked position and turn off. Its last movements are automatic.

The intermittent part of the problem can be the contact switch on the turn stalk but there is a timer box on some models which the stalk switch controls. Some wiper motors have the timer box beneath a shield on the wiper motor. Those controls can be changed.

Mar 19, 2014 | Ford Fusion Cars & Trucks

2 Answers

2012 VW Passat - in cold weather wipers dont work


Can you getting into some place above 32f or 0c? If so do. Let it warm up and see if it helps. The grease maybe to thick in the transmission of the wipers two there could be ice or snow packed around the unit.
If it was doing it when it was warmer check the units ground.

Feb 28, 2014 | Volkswagen Jetta Cars & Trucks

2 Answers

Intermittent wiper


what car, what year? gee? a suz, what?
it can only be 4 things. (all cars)
1: the wiper motor is bad. (it has contacts inside for timing.
2: the wiper shaft is stripped, nah you said both stalled.
3: the wiring is bad.
4: the combo switch for the above is bad.

DIY, with what , no tools? no meter.?
with no tools one can only GUESS,
roll dice, and replace a part.
after spending $500 on parts and the wires are good then what.
yes, buy a meter.

it could be a bad ground wire.

when you turn on most wipers, the combo switch sends
that signal( just 12v ) to the motor.
the motor is self booting, that is , it only needs the start up
and then it self provides its own power,
ive restored wiper motors, many.
then the motor runs until it his the dead spot in ITS, internal
sustain switch and the halts. if the combo switch is off.
but if the wiper fails to return, this is a bad wiper motor.
(overloaded by ice, sure)
the motor can fail 2 ways, but
id say the sustain switch is at EOL. end of life.

this is the most common design.
check your FSM for yours. the factor service manual.
or alldata dot com. sure.

Sep 25, 2013 | Suzuki Cars & Trucks

2 Answers

Wipers don't work on intermittent. They run but stop in they middle of the windshield and don't go to the bottom like normal, Then they run again and stop some other spot. When put on continuous they...


Intermittent Speed Windshield Wipers
The intermittent wiper speed is activated with grounds controlled by the multifunction switch inputs to the windshield wiper motor module. The windshield wiper motor module then activates the windshield wiper RUN/PARK relay coil and switches voltage through the windshield wiper high/low relay. The high/low relay remains deactivated supplying the voltage to the wiper motor low speed input and activates the windshield wiper motor. When the windshield wiper motor module receives the grounded input, the motor continues to operate until Hall effect senses magnet to turn off RUN/PARK sense the output to the windshield wiper RUN/PARK software, deactivating the relay and disconnecting voltage to the wiper motor. The windshield wipers remain parked until the windshield wiper motor module completes a time-out and then repeats the intermittent windshield wiper cycle.

  • The intermittent windshield wiper speed does not operate correctly
  • Multifunction switch.
  • Circuitry.
  • Windshield wiper motor.
  • Go To Pinpoint Test D .

Pinpoint Test D: The Intermittent Windshield Wiper Speed Does Not Operate Correctly
Normal Operation During normal operation, the windshield wiper motor receives voltage at all times through battery junction box (BJB) fuse 1 (30A), circuit 65 (DG). The windshield wiper motor also receives power with the ignition switch in RUN or ACC positions through central junction box (CJB) fuse 33 (15A), circuit 1002 (BK/PK). Ground is provided to the windshield wiper motor through circuit 676 (PK/OG) and circuit 57 (BK). The run/park and high/low relays are contained in the wiper motor electronics. Mode of operation is dependant on the signal(s) received from the multifunction switch.
    Possible Causes
  • Multifunction switch
  • Open in circuit 57 (BK), 56 (DB/OG), 61 (YE/RD) or 63 (RD)
  • Windshield wiper motor
PINPOINT TEST D: THE INTERMITTENT WINDSHIELD WIPER SPEED DOES NOT OPERATE CORRECTLY Test Step Result / Action to Take D1 CHECK THE MULTIFUNCTION SWITCH
  • Key in OFF position.
  • Disconnect: Multifunction Switch C202b.
  • Carry out the multifunction switch component test. Refer to Wiring Diagrams Cell 149 for schematic and connector information.
  • Did the multifunction switch pass the component test?
Yes
GO to D2 .

No
INSTALL a new multifunction switch. REFER to Section 211-05 . TEST the system for normal operation. D2 CHECK CIRCUIT 57 (BK) FOR OPEN
  • Measure the resistance between multifunction switch C202b-6, circuit 57 (BK), harness side and ground.
  • Is the resistance less than 5 ohms?
Yes
GO to D3 .

No
REPAIR the circuit. TEST the system for normal operation. D3 CHECK CIRCUITS 56 (DB/OG), 61 (YE/RD) AND 63 (RD) FOR OPENS
  • Disconnect: Windshield Wiper Motor C125.
  • Using the following table, measure the resistance between multifunction switch C202b harness side and windshield wiper motor C125 harness side:

    Multifunction Switch C202b Windshield Wiper Motor C125 Pin 2, circuit 56 (DB/OG) Pin 10, circuit 56 (DB/OG) Pin 4, circuit 61 (YE/RD) Pin 1, circuit 61 (YE/RD) Pin 1, circuit 63 (RD) Pin 9, circuit 63 (RD) Pin 3, circuit 58 (WH) Pin 11, circuit 58 (WH)
  • Is the resistance less than 5 ohms?
Yes
GO to D4 .

No
REPAIR the circuit(s) in question. TEST the system for normal operation. D4 CHECK FOR CORRECT WIPER MOTOR OPERATION
  • Disconnect all wiper motor connectors.
  • Check for:
    • corrosion.
    • pushed-out pins.
  • Connect all wiper motor connectors and make sure they seat correctly.
  • Operate the system and verify the concern is still present.
  • Is the concern still present?
Yes
GO to D5 .

No
The system is operating correctly at this time. Concern may have been caused by a loose or corroded connector. TEST the system for normal operation. D5 CHECK THE WINDSHIELD WIPER MOTOR
  • Key in OFF position.
  • Disconnect: Windshield Wiper Motor C125.
  • Carry out the windshield wiper motor component test as outlined in this section.
  • Did the windshield wiper motor pass the component test?
Yes
The system is operating correctly at this time. Concern may have been caused by incorrect binding pivot arm adjustment. REFER to Wiper Blade and Pivot Arm Adjustment in this section. TEST the system for normal operation.

No
INSTALL a new windshield wiper motor. REFER to Windshield Wiper Motor in this section.

Feb 19, 2018 | 2006 Ford F 350 Super Duty

2 Answers

Dodge caravan 1996 During cold weather wiper malfunction


Hi

Sounds to me like the "parking" contacts inside the wiper motor have broken off / worn.
Needs to remove wiper moter / dismantle to inspect. (On some models you can purchase these contacts.)

Dec 10, 2009 | 1996 Dodge Caravan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

219 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

80339 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...