Question about 1992 Toyota Camry V6

Open Question

Toyota Camry V6 valve tapping

I have a 1992 Toyota Camry V6 and I replaced the head gaskets. I have the head and the valve worked done. When the engine is hot there is clocking noise inside the valve cover and if its park and try to rev up the engine and let the gas pedal go that is when I hear the cloking noise but if it's on high rpm it don't have that noise.I checked the valve clearance and adjusted it by shimming . I repeat this process cause it did not do nothing on the first time. Besides all that noise my car runs fine and has a good gas millage. Please help.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1861 Answers

SOURCE: 1997 Camry Valve Cover Gasket Replacement

Removal of the plenum is pretty straight forward. You will need to replace the plenum gasket after you remove it; the gasket is not reusable. Personally, if I was going to take the trouble to remove the plenum, I would replace the plugs and wires back there, also.
I know, I have a 93 Camry V6, and it is a real pain to do the plugs and wires with the plenum on. There are no secrets or great tips on the plenum removal, just take your time. Remember that there are different size bolts, and where they go. Please get back to me if you need any more info...Hope this helps, and thanks for choosing FixYa to resolve your issue.
The graciousness of a FixYa rating for my assistance would be greatly appreciated.

Posted on Dec 15, 2008

Ad
  • 43 Answers

SOURCE: Cam bearings

this is a major overhaul , if you don't do it right you will damage many things

Posted on Jan 06, 2009

  • 160 Answers

SOURCE: 1992 Toyota Camry Rough Idle

start by pulling hose off egr valve see if idles smoother almost instantly

Posted on Mar 17, 2009

  • 23 Answers

SOURCE: engine check light read p0171 and p0420, noticed a leak of engine oil on cylinder 2 area of head gasket when checking the sparks plug, is that the cause?

may be oil feed to cylinder head replace gasket

Posted on Apr 20, 2009

  • 8 Answers

SOURCE: Toyota 1jz engine,are they hydraulic or shim

Shims and Valve clearance cold : 0.15-0.25mm (in)
0.25 0.35mm (ex)

Posted on Aug 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i replace a vacuum switching valve on a 1992 toyota camry 2.2L engine


Your post says it is a v6 but you say a 2.2 4 cyl in your question. VSV is located near the rear of the valve cover on the front of the engine.

Mar 22, 2014 | 1992 Toyota Camry V6

1 Answer

I have a 1992 Toyota camry and the transmission was slipping and theni was stuck in a traffic jam and the temp went up and now the idol is really rough and the car seems to only be running on 3 cylinders...


Did the car overheats? If so, have someone check for a possible blown head gasket or cracked head. Have them do a compression check in the cylinders.

Feb 09, 2018 | 1992 Toyota Camry V6

2 Answers

I replced my radiator & thermostat and my car is still overheating. Toyota Camry 1992, help


water pump may be bad. or you may have a head gasket leaking. If it perks over out of the radiator before it really hot thats a sign you have a head gasket issue. A shop can tell you for sure with a smog machine. If you have gas in your water the smog machine will read it.

Nov 22, 2009 | 1992 Toyota Camry V6

1 Answer

1992 toyota camry shaking very bad could this be a blown head gasket.. the machanic says its the first spark plug


Hi,

When a cylinder is misfiring, this dirupts the balance of the engine and the computer is sometimes unable to compensate during a misfire.

This also, can often cause erratic engine behaviour...and shaking like a tank.

It may simply be a bad spark plug, HT lead, or something more serious.

Have the onboard diagnostics checked first - this will indicate which (if any) electrical component is at fault.

This can be done by a local Toyota dealership, with the correct scanning equipment.

Nov 12, 2009 | 1992 Toyota Camry V6

2 Answers

How do I replace my valve cover gaskets on my 1992 toy cam v6 3.0


this is relatively easy unbolt the cover from the head (this usually requires a 10 milimeter socket)once unbolted pull the cover off make sure you clean the old gasket off the cover and the head glue the gasket back to the cover and reverse the process used to take it off be careful not to over tighten the new gasket so as not to split it and cause it to leak.

Oct 03, 2009 | 1992 Toyota Camry V6

2 Answers

92 toyota camry v6 do they have 2 heads or just 2 cams


That is possible if it is not dual overhead cam if it is single overhead cam that would be right.

Mar 04, 2009 | 1992 Toyota Camry V6

Not finding what you are looking for?
1992 Toyota Camry V6 Logo

Related Topics:

204 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...