Question about 1995 Lexus ES 300

1 Answer

Car turns over but wont start

Just rebuilt head, put all back together and it wont start. turns over but will not start?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

1 make sure timing is good.
2.check all the sensors make sure they all plugged in(some cars has same plugs for different sensors make sure you gut the right sensor for right plug)
3. Pull one spark plug of and see if it has any fuel on it.if it does you might flooded the motor.
4if none of the above works you should do compression tests on the cylinders.
Thanks

Posted on Apr 15, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

89 gmc I have spark and fuel but wont start


Timing. Your probably not TDC.

Mar 20, 2013 | 1989 GMC K1500

1 Answer

Do i need to have my 2004 dodge intrepid anti theft code reset through a dealership if the heads and head gaskets were replaced? the entire top of the engine ws taken apart adn put abcl together.


i would disconnect the battery. removing both the positive and negative battery terminals. with both ends disconnected, hold the two terminals together for about 10 seconds. this will proform a hard reset on most chrysler vehicles. also, if this doesnt work, try turning the key to the on position, and then proforming the hard reset procedure.

Nov 04, 2012 | Dodge Cars & Trucks

1 Answer

What causes hyundai code p0102, and no starting?



Trouble Code: P0102

Mass or Volume Airflow Sensor Circuit Low Input
Possible Causes:


MAF sensor signal circuit is open or shorted to ground. MAF sensor power (VREF) circuit is open or shorted to ground . MAF sensor is damaged or has failed. PCM has failed .Here's the code for your problem,it may be a maf sensor. The MAF is mounted in the intake air hose of the air cleaner assembly. On some vehicles, it is combined with the IAT sensor.

Sep 04, 2012 | 2005 Hyundai Santa Fe

1 Answer

My 1990 toyota wont shut off when the key is off


Then the main relay is shorted together possible,recheck the ignition electrical by disconnecting it first and see if you get that click when you put the battery together,if you dont the ignition electrical is the problem if you still do the circuit opening relay along with the main is the problem3_18_2012_12_05_45_am.jpg

Mar 17, 2012 | 1990 Toyota Tercel

1 Answer

Put rebuilt head on now engine smokes and has aqlot of blow by


any time you put a new or rebuilt head on top of a used motor you are going to get some sort of blow by. the more miles one the Rings the more blow by you will have. when you put on the rebuilt head south the new valves. you increased the compression ratio. thus making the worn rings from being able to hold back all the compression. next time at least drop the pan and put new rings in. better new pistions and hone the cylinders. best pull the block have it bored .20 over (which gives you a 2.0L ) have the crank turned. have the cams inspected for ware. and just replace old with new. yes.its more expenses in the beginning but well worth it. because look were you are now. to fix it you now have to start over with a lighter wallet

Mar 17, 2012 | 2007 Chevrolet Aveo 5 Hatchback

1 Answer

96 grand am turns over wont start.


Check the crank sensor. And the cam sensor

Oct 21, 2009 | 1996 Pontiac Grand Am

1 Answer

Steam and water coming out of my exhaust


Sounds like a cracked cyllinder head

Aug 25, 2009 | 1986 Mazda 626 Coupe

1 Answer

How do i get the car started


I would start by backing up and check cam timing.

Jun 17, 2009 | Hyundai Excel Cars & Trucks

1 Answer

Rebuilt head put oon..missing something....fuel pours out when started


carbeuretor float is stuck or engine timing is totally out meaning fuel lift pump is supplying cylider while inlet valves are closed

May 29, 2008 | 1998 Mazda Protege

Not finding what you are looking for?
1995 Lexus ES 300 Logo

Related Topics:

133 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

902 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...