Question about 1999 Dodge Avenger

2 Answers

How to change a headlight bulb on a 1999 dodge avenger?

I'm having trouble replacing the burnt out headlight bulb on my 1999 dodge avenger. I don't know where to start and I'm worried about making a mistake.

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

You have to open the hood and go at it from behind the bulb. look behind the light fixture set up and you will see where the light bulb goes. Simply twist off and pull out. the old light bulb will com out also.

Posted on Jul 15, 2009

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 14 Answers

Under the hood in behind the head light is where the bulb goes dont touch the glass on your new bulb

Posted on Jul 28, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Driver side rear turn signal and brake light don't work when I turn on headlights,


Check your wiring and connections for the affected light. This is symptom of a bad ground for the dual filament bulb.

Dec 28, 2016 | 2012 Dodge Avenger

1 Answer

Have a 1999 Dodge Avenger V6. Keeps blowing Engine Fuse under hood


Fusible link 3 feeds the PCM. the ASD relay, and fuel pump relay. Assuming it has A/T, that fusible link also feeds the starter relay, the EATX-ECM, and the EATX relay. A short in any of those elements could be causing the trouble.

Dec 16, 2016 | 1999 Dodge Avenger

1 Answer

To replace a blown turn signal light on a 2010 dodge avenger ?


front or rear cause ya may not have to remove any screws on headlight assembly's ya have to get to the back where the wires hook up and twist the socket to get to the bulb same on tail lights but ya have to go through the trunk

Dec 28, 2014 | 2010 Dodge Avenger SXT

1 Answer

Dodge 1999 neon headlight broken something is broken


dont tack it back cause they will say that you broke it and you fixed it. just try and replace the light housing and your plug

Jan 18, 2014 | 1999 Dodge Neon

1 Answer

How do I change the headlight bulbs, I took off the clips but cannot remove cover


You do not have to remove the cover the bulbs simply pull out of the back just twist and pull

Sep 04, 2011 | 1998 Dodge Avenger

2 Answers

I want to replace the bulbs for my headlights on my 2008 Dodge Avenger. Must I take it to a mechanic?


you could do this yourself,, but if the lights are still working why bother? if there broken change them ,,just dont tuch the glass on the bulbs with your fingers,,it causes them to blow early,,so hold them in paper

Nov 28, 2010 | 2008 Dodge Avenger

1 Answer

Need to replace headlight lens on a 1996 dodge avenger


Usually, one has to get the entire headlight assembly to replace the lens.
Is it cracked?
If it is just faded, try some anti-haze polish for headlights. This can save you some money compared to restoring the headlamp by replacing the assembly (which may be available from a salvage yard).

---
REMOVAL & INSTALLATION

CAUTION
Halogen bulbs contain gas which is under
pressure. Handling the bulbs incorrectly could cause it to shatter into flying
glass fragments. Do NOT leave the light switch ON. Always allow the bulb to cool
before removal. Handle the bulb only by the base; avoid touching the glass
itself. Whenever handling a halogen bulb, ALWAYS follow these precautions:

  • Turn the headlight switch OFF and allow the bulb to cool before
    changing it. Leave the switch OFF until the change is complete.
  • ALWAYS wear eye protection when changing a halogen bulb.
  • Handle the bulb only by its base. Avoid touching the glass.
  • DO NOT drop or scratch the bulb.
  • Keep dirt and moisture away from the bulb.
  • Place the used bulb in the new bulb's package and dispose of it properly.


Cirrus, Stratus, Sebring Convertible and Breeze


  1. Open the vehicle's hood and secure it in an upright position.
  2. Disconnect the negative battery cable.
  3. Remove the 2 screws securing the headlight module to the radiator closure
    panel.
  4. Pull out the headlight module from the vehicle.





    Fig. 1: Using a Torxhead screwdriver, remove the 2 headlight
    module retaining screws
    90906p69.jpg






    Fig. 2: Pull the headlight module straight out of the front of
    the vehicle to remove the bulbs
    90906p70.jpg






    Fig. 3: Disconnect the wiring harness for the headlight bulb
    90906p74.jpg






    Fig. 4: Turn the light bulb retaining ring counterclockwise,
    and remove it from the back of the module
    90906p75.jpg






    Fig. 5: Pull the light bulb out from behind the module. Never
    touch the glass of the light bulb
    90906p76.jpg



  5. Detach the headlight electrical connector.
  6. Remove the retaining ring holding the bulb to the back of the headlight
    module.
  7. Pull the bulb from the back of the headlight module. Hold the bulb by its
    base only; try not to touch the glass itself.
    To install:

  8. Holding the bulb by the base, place it in the headlight module, then secure
    with the retaining ring.
  9. Attach the electrical connector to the bulb.
  10. Install the headlight module into the vehicle and tighten the 2 retaining
    screws.
  11. Connect the negative battery cable and check the headlight operation.


Sebring Coupe and Avenger


  1. Open the vehicle's hood and secure it in an upright position.
  2. Disconnect the negative battery cable.
  3. Remove the sealing cover by rotating it counterclockwise.
  4. Remove the bulb attaching spring and pull out the light bulb.





    Fig. 6: Remove the headlight sealing cover(s)
    90906g28.gif






    Fig. 7: Remove the attaching spring and pull out the bulb
    90906g29.gif

    To install:

  5. Install the bulb into the headlight module.
  6. Install the bulb attaching spring.
  7. Install the sealing cover.
  8. Connect the negative battery cable and check the headlight operation.


prev.gif next.gif

Oct 07, 2010 | 1996 Dodge Avenger

3 Answers

I changed my headgasket on my 1999 dodge avenger and water pump spark plugs even the hydraulic timing belt tensionerand it is still misfiring


Why did you change the head gasket Patrick,
Was the engine missing before you did this,or did you over heat the engine from low coolant?
If the miss was there before you may have burnt a valve,

Jan 23, 2010 | 1998 Dodge Avenger

1 Answer

Replace Bulbs in Headlight. 2008 Dodge Avenger


there is 2 bolts on top 1 top outer and 1 top front behind grill, u need to remove the top center black cover and 1 bottom side outer need to remove the inner finder liner to get to the 3rd bolt.
hope that helps, it is stupid

Mar 09, 2009 | 2008 Dodge Avenger

1 Answer

96 Dodge Avenger...replacing headlights!!


you have to unscrew the round white houseing on the back of the head light assembly and then reach inside the headlight and pull the clip out then the bulb and wires come right out i know its a pain in the a#@ to get your hand in there but your only other choice is take the whole headlight assembly out and that is an even bigger project also the clip holding it in is kinda like a U clip and the bottom is attached so dont pull it out completly it kinda justs pivits itself out of your way

Aug 13, 2008 | 1996 Dodge Avenger

Not finding what you are looking for?
1999 Dodge Avenger Logo

825 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8211 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...