Question about 2005 Chevrolet Uplander

1 Answer

2005 Chev Uplander abs light on...I replaced two front wheel bearings and light still on saying to check abs system...?????

Posted by on

  • 1 more comment 
  • poppy658 Apr 15, 2009

    The harness to the abs brakes seems to be a little rusty...

    How much time would it take to replace the harness to abs system...

    and do I have to replace the whole harness to the four wheels//



    thanks....

  • poppy658 Apr 17, 2009

    Thanks for your help in answering my questions....one more

    If I did not replace the harness would i be doing any harm to the abs brake system...

  • Anonymous Mar 16, 2014

    service abs system 2008 chevy uplander p1178

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Chevrolet Master
  • 420 Answers

Did you plug the sensors back up?

Posted on Apr 14, 2009

  • Scott Apr 15, 2009

    Replacing the harness is a big expensive job. I would clean up the rust and apply some dialectic grease to the plugs.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to reset ABS light on 2005 chevy uplander


you cannot its that simple the ABs computer is the only one that resets itself so if light on then you have a fault with a sensor on a wheel of the magnetic disk on the back of a bearing or on older the cars the toothed ring is loose .

Nov 10, 2016 | 2005 Chevrolet Uplander

1 Answer

2005 Chevrolet Uplander ABS Light goes on and off


Could be only the sensors need to be replaced.

Aug 26, 2017 | 2005 Chevrolet Uplander LS

1 Answer

Service abs system light comes on all the time. both front wheel bearings have been replaced, abs light stays on.


i had the same problem with my 2005 chevy uplander. the ABS lights kept coming on. The fix for me was... I had a damaged and old battery(the original battery). If your still under warranty or not I would suggest you check this out by using a new battery to see if this is your solution.

Dec 16, 2011 | 2006 Chevrolet Uplander

2 Answers

LEFT FRONT WHEEL BEARING IS MAKING A REAL LOUD NOISE AND THE abs LIGHT IS ON. what COULD IT BE?


Well, start by repairing the obvious issue. ABS sensors are located in the same area, so when the bearing fails, metal filings go everywhere and mess up ABS sensing...

Sep 06, 2010 | 2007 Chevrolet Uplander LS Minivan

1 Answer

All Wheel Drive Disabled


I would take it back to place where it was repaired, it is possible that the part they replace is defective..

Also they should have clear all codes in the system at that time!!!

Jan 03, 2010 | 2005 Chevrolet Uplander

1 Answer

How do i turn off the abs light on a 2005 chevy uplander? replaced front pads and checked wires and connections. is there a way to see if the anti-locks are working?


Hello Abintz.
When your ABS light is on you have a problem in the system.
As long as the light is on your ABS system does not function at all.
If you have already checked the harness and connections the next thingt you can check yourself is resistance values at the wheel speed sensors.
One at each front wheel and one in the output shaft housing to the rear drive shaft.
They should read very close to 1000 ohms.
The front sensors are usually the area of most problems I see. They are replaceable.
Other than that you really would be hard pressed to find any other issues without getting it scanned by a repair shop.
If you have further questions please put them in "add comments and I will return to answer.
Best of the season to you.

KL

Dec 20, 2009 | 2005 Chevrolet Uplander

3 Answers

2003 chev. silverado2500hd, abs goes off, pulsates when stopping


Gm has tech service bulitens on this issue.First the abs sensors can and should be removed,inspect the sensor mounting surface for rust (clean w/ sandpaper) insp the sensor (note the sensor may break w/ trying to remove so be gentlel) if all looks ok reassemble and test drive. if unwanted abs still persists both hub bearings should be replaced (call your dealer and ask if a special policy exsits for this condition) usually no abs code w/ be present Good luck Ray..

Jun 15, 2009 | 2005 Chevrolet Silverado

1 Answer

Abs light on 2005 chev uplander...


You will have to check ABS codes to determine what the problem is.

May 02, 2009 | 2005 Chevrolet Uplander

2 Answers

2007 Chevrolet Uplander LT ABS and TC light on


We were having this problem...have your wheel bearing checked out. There was a sensor in the drivers side wheel bearing...once we replaced it (because it was going out) the ABS and Traction Control warning lights stopped coming on.

Dec 02, 2008 | 2007 Chevrolet Uplander LS Minivan

Not finding what you are looking for?
2005 Chevrolet Uplander Logo

1,127 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6924 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...