Question about 1991 Honda Accord

1 Answer

Blower moter will not work need to find the location

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Honda Master
  • 75,814 Answers

The motor is located behind the glove box on the passenger side under the dash, here is the change out procedure.

First, remove the glove box...easy three screws total. Two on the bottom, and one holding the shock on the right side. Second, remove the metal bar that is behind the glove box...four phillips screws. Third, remove the two bolts securing the dash on the right side. Fourth, remove the small RH kick plate...pull hard it has three clips. Fifth, remove the two screws on the bottom of the fan housing and remove the bottom diffuser...small plastic peice. Sixth, remove the front center metal clip and remove this small plastic piece. Seventh, pull the carpet back on the passenger side and remove the four nuts securing the computer to the floor board and swing it out to the left. Next, disconnect the neg terminal on the battery and remove the three plugs that were near the RH kick plate. Now comes the fun part. The dash will be hindering the removal of the blower motor housing. First, remove the metal band securing the blower motor housing and the heater core housing together. It's one 10mm bolt at the top. This band clips to another band securing the two housing together on the back side. You will also need to remove the two small phillips screws securing the rear band to the blower motor housing...one on the top and one on the bottom. The rear band gets in the way when removing the housing. So when the housing assembly drops remove the rear band from the top...set this part in first on installation. Last, remove the four 10mm nuts securing the blower motor housing to the firewall. The housing will not fall to the floor on its own. You will need to pull up and out on the bottom of the dash while guiding the housing assembly down and to the left. Be careful not to pull aggressively on the dash. It's sturdy, but will crack if you are too rough.

Posted on Apr 14, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Heater controls and blower moter


do you have power at the blower? does it work on any speed?check all fuses and relay. also, look into the blower motor resistor, located next the the blower itself

Nov 03, 2012 | Toyota Tacoma Cars & Trucks

1 Answer

Where is the heater blower moter on my skoda octavia classic 1.9 sdi model 2003


Under the dash on the passenger side, remove any panels under daash to expose it.

Oct 01, 2012 | Cars & Trucks

1 Answer

My heater motor only works on high


A bad blower moter resistor can cause the blower to default to high speed only. The resistor is
located behind the lower right side of the dash on the heater box just left of the blower moter.
The fan switch can also cause this problem, but more often then not it's a bad resistor.
Hope this helps.

Nov 22, 2010 | 2006 Chevrolet Colorado

1 Answer

FAN BLOWER (FOR A/C AND HEAT) ONLY BLOWS ON THE HIGHEST SETTING. IS THERE A FAN SPEED CONTROL OR RELAY THAT CAN BE REPLACED, OR IS IT SOMETHING ELSE?


Hello leebarker
The blower moter switch or the blower moter controler can cause this
problem. Remove the plug from the switch, use a 12v test light to locate
the 12v power wire in the plug. Next with a small jumper wire bring power from the 12v contact to the low and medium speed contacts on
the plug if the blower changes speed replace the switch if it still only
has high replace the controler. The blower controler is located on the
passenger side end of the heat-a/c box near the blower moter.
By the way the key must be in the on position for this test.
I hope this helps. Good luck.

Jul 10, 2010 | 2002 Jeep Grand Cherokee

2 Answers

My heater and AC blower not working. Please help


In the fuse block,under the hood on top of the fender. Locate fuse #35 it's 40amp fuse for the blower moter. If the fuse is ok,there is another
common problem you can check. The blower moter resistor assembly,
located under the dash on right side. With a 12v test light check for
power to the blower moter from the resistor. If you have no power to the
moter, replace the resistor assembly. If niether of these works, I'll need
to know if you have climate control or manual control hvac. And for some reason, the wheel base. long wb or short wb. to dig any deeper.
But I hope one of the causes I've mentioned will cure the problem.
Good luck.

Feb 26, 2010 | 2005 GMC Envoy

1 Answer

My heater will not turn on


if the blower motor won't turn on try replaceing the blower motor resistor located on the heater box under the hood

Jan 13, 2010 | 1996 Mercury Cougar XR7

1 Answer

Blower moter won't run blower good


replace the fan resistor located on the side of the heater box under the dash usually on the passenger side this controls the fan motor speed along with the switch itself.

Dec 08, 2009 | 1999 GMC Safari

1 Answer

Blower motor 94 dodge intrepid inop


1.disconect battery
2. remove lower right undre panel silencer duct
3. remove the blower moter connector from the resistor block
4. squeeze the blower moter wiring gromment and push the gromment throw the blower moter housing cover
5. remove blower moter housing
6.romove the screws holding the blower moter down
to put back on do the steps back werds

Jan 03, 2009 | 1994 Dodge Intrepid

2 Answers

Blower motor installation and location


location is right side under dash , procedure is remove right sound insulator , disconnect blower motor connectors , remove blower motor cooling tube , remove the blower motor screws and blower motor , and reverse procedure to install .thanks.

Dec 28, 2008 | 1998 Chevrolet Cavalier

Not finding what you are looking for?
1991 Honda Accord Logo

138 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...