Question about 2001 Hyundai Santa Fe

1 Answer

Is it hard to change crank shaft position on hyundai santa fe 01

Hyndai runs good for 1/2 an hour then stops and won't go.

Posted by on

  • yadayada
    yadayada May 11, 2010

    have u run a trouble code test on this problem?

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 3 Answers

2.7 engine located above the starter. You need to remove the starter outherwise its fairly easy.
The 2.4 & 3.5 engine, its located in the front next to the timing belt, a little more complicated to to install.

Posted on Aug 18, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No spark, 2004 hyundai 3.5L santa fe


a cam sensor symptom is car running rough if no spark sounds like crankshaft sensor

Apr 19, 2014 | 2004 Hyundai Santa Fe

1 Answer

No spark on the ignition coils


my car would turn over but wouldn 't start, after changing all the same stuff you did it kept not starting again , so i changed the purge control valve and it's been good so far . seems to be a common problem, there are 2 on the car but they say its the one on the engine they always replace, better check that first to be sure.

Mar 28, 2014 | 2003 Hyundai Santa Fe

1 Answer

Piston positions in 2004 hyndai santa fae


I were awakened by a loud explosion that sounded like a tire on an 18 wheeler blew out on the interstae nearby. then within seconds a smaller sxplosion and the 'panic' alarm on our 2008 Syundai Santa Fe started on go off. by the time I reached the window to look out on our driveway the rear drivers side of our 2008 Santa Fe was engulfed in flames, and only 3 feet from our house and parked next to our 2001 GMC 'Jimmy". One of our neighbors was frantically screaming for us to get out of our house and pounding on our front door. The vehicle had not been driven for over 2 days --- it just spontanousely erupted in flames.
WHY? Has anyone ever heard of anything like this happening to a new Santa Fe with less than 2,500 miles on it?

Jul 29, 2012 | 2004 Hyundai Santa Fe

1 Answer

2001 hyundai santa fe starts with one crank but won't go into drive or reverse, only goes into park and neutural what could be the problem? i have a 2001 hyundai santa fe 2.7 l v6 all wheel drive


You do have drive and reverse,if you have park and neutral.It just the transmission cant transfer that power a new or rebuilt is the solution

Mar 20, 2012 | 2001 Hyundai Santa Fe

1 Answer

WHERE IS THE CRANK SHAFT SENSOR LOCATED


The 2002 Santa Fe came with three (3) possible powertrains (engines). The 4 cylinder, and two different V6 engines - i.e. 2.4L 4 cylinder, the 2.7L V6 and the 3.5L V6.

The crankshaft position sensor on the 4 cylinder and the 3.5L V6 are in the same place - Front Crank Shaft behind the pully (behind the timing belt cover.

On the 2.7L V6, the Cranshaft Position Sensor is located in the engine block (Left Hand Side)
near the flywheel (adjacent to the LH (Bank 2) exhaust manifold.

Note: Left Hand Side means the radiator side (front) Bank 1 is the firewall side.

Jun 30, 2011 | 2002 Hyundai Santa Fe

1 Answer

Whenever it rains my 2004 Hyundai Santa Fe will not run well. Today it sputtered and died several times. Now its running again that it has dried out. What is causing this?


We went through this with ours recently. Hyundai diagnosed it as a bad crank shaft position sensor. We replaced it and we're up and running again. Not sure why the damp weather affected it but it did.

Sep 20, 2010 | 2004 Hyundai Santa Fe

1 Answer

Hyundai santa fe 2002 was running good parked in garage over night got ready to leave next morning and it started like normal but before I put my seat belt on it died, it will crank but not start, had...


I have just had similar problem was on my way to work and car just stopped like it ran out of fuel . my balance shaft belt broke which caused the timing belt to jump a tooth still waiting for a quote for repair its up to $2000 so far through hyandai. after looking at other web sites realised this is a common fault with 2002 santa fe. you may want to get the crank angle sensor checked as well as my car has done two so far. hope this helps and your car is not as serious as mine

Aug 22, 2010 | 2002 Hyundai Santa Fe

1 Answer

My '01 Santa Fe awd v-6 has a new transmission, now sometimes won


Bases on the limited info provided, most likely the ignition switch. If you list the symptoms you experience when it doesn't start it would be easier to diagnose your problem for example: does it crank? does the key turn and do nothing? etc. Hope this answers your question.

May 02, 2009 | 2004 Hyundai Santa Fe

Not finding what you are looking for?
2001 Hyundai Santa Fe Logo

Related Topics:

224 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...