Question about Jeep Liberty

1 Answer

Power windows and door locks not working ,checked all fuses look good?

Power windows and door lock do not work ,fuses look good

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

My jeep liberty passenger side door won't open and the window won't go up or down....what is the problem?

Posted on Mar 16, 2010

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
TwinTurboZ
  • 78 Answers

SOURCE: power windows and power doorlocks won't work

Try replacing your window switch on the drivers front door.

Posted on May 19, 2009

MrScary66613
  • 1990 Answers

SOURCE: Power windows, locks, and seat not working

That Clicking should be a Bad Relay Switch. See if you can Locate it and Replace it. It should fix this Problem for ya! Please Rate My Response! Thanks!

Posted on Jan 31, 2009

  • 1 Answer

SOURCE: colorado door locks

2005 colorodo driver window and door locks do not work. did work untill i pulled the negative side of the battery trying to reset a problem i had with the door lock alarm going off when unlocking with the pov. everything seems to be o.k. same settings on dic. controls.

Posted on Feb 14, 2010

  • 68 Answers

SOURCE: 2005 Chevy Colorado drivers side window, and power locks

Check for door ajar switches not making contact.

Posted on Mar 08, 2010

  • 1 Answer

SOURCE: door locks and power window

Just did this procedure I got from coloradofans.com forums:

"any type of power/voltage change seems to trigger this issue

The most common symptom is power locks fail and only the driver window quits, however that is on the extended cab.

Steps to fix and it works every time.

take door panel off driver's door
Disconnect the wiring attached to window and power lock control unit
disconnect battery cables
connect the negative to the positive cable(((NO BATTERY CONNECTED)))
This will act to short residual voltage in the system

5 minutes later
place the key in the ignition and turn to the run position
connect the wiring to the window/lock controller
connect the negative cable to the battery
then the positive
open drivers side door
turn key to the off position((do not remove yet)) you should get a series of dings through speakers telling you the key is still in the ignition
once it begins dinging pull the key out and you should hear the door lock solenoids trigger and the windows should work." - Coloradofans.com forums

Posted on Mar 20, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why don't power locks work?


it maybe the BCM may have a problem or needs to be reset.

Sep 06, 2015 | 2010 Chevrolet Chevrolet Malibu LT

1 Answer

Windows, mirrors and power door locks don't work


Did you check the relays or just a fuse?

Apr 18, 2014 | 2000 Buick Park Avenue

1 Answer

All windows except the driver's side are not working.


First, if the driver's window is working, there is no need to waste your time looking for fuses. ALL of the windows are powered by the SAME fuse.

The first thing I recommend checking is the window "lock" switch on the master switch. If it is in the "lock" position, none of the other windows will work (it is designed to do that)

Other than that, you need to check for power and ground at all of the other door switches. The BLUE/BLACK wire at each of the switches should have battery voltage anytime the ignition switch is in the ON position. If they do not, the wire is broken between the splice near the driver's door and the right front door. Both the RED and the GREEN wires at each switch should have continuity to ground anytime the master switch is at rest with the "lock" switch in the unlock position (the lock switch breaks these grounds to "lock" the windows and prevent them from being operated).

Jan 31, 2012 | 1991 Mitsubishi Montero

2 Answers

Doorlocks dont work except from passenger side. mirrors dont work. windows dont work from anywhere


First, check all fuses to make sure that none are blown.

If the door lock switch works on the passenger side, then the drivers side door lock switch is probably faulty. Use a multi-meter to test the Drivers Side Door Lock Switch (Black and Pink/Light Green wires unlock the vehicle, and the Black and Pink/Yellow wires lock the vehicle)
If the switch is tested and found to be operating properly, you may have a faulty Body Security Module or Drivers Side Door Lock Actuator.

If neither of your Power Mirrors are working, you probably have a faulty Exterior Rear View Mirror Switch, Power Mirror Module, or blown Central Junction Box Fuse.

If none of your Power Windows are working, you probably have a faulty Accessory Delay Relay or a blown fuse in your Central Junction Box or a faulty Master Window Adjust Switch (all of the Power Window Switches feed through this Master Window Switch). If the Power Windows didn't stop working at the same time, you may have faulty Window Adjust Switches, or faulty Power Window Motors, this is very unlikely though. It would also be a good idea to inspect the wiring for any obvious damage.

Mar 15, 2011 | 2005 Ford F-150

2 Answers

Automatic door locks stopped working. Power window controls do not work. The only window working is drivers window.


Change the battery in your wireless remote control. Check the fuses located underneath the drivers side steering wheel, flip the fuse box cover lid over and replace the power window and power door lock fuses. The back of the cover lid will have a diagram showing where each fuse is located, replace with the same number amp fuse. If your fuses are good and the battery inside your remote is new then you will need to replace the drivers side power window switch, click on the link below to view a replacement:

http://cgi.ebay.com/ebaymotors/05-06-Toyota-Tundra-OEM-Master-Power-Window-Switch-LKQ-_W0QQcmdZViewItemQQfitsZYearQ3a2006Q7cMakeQ3aToyotaQ7cModelQ3aTundraQQhashZitem20b3f6b69aQQitemZ140458243738QQptZMotorsQ5fCarQ5fTruckQ5fPartsQ5fAccessories

Oct 18, 2010 | 2006 Toyota Tundra

1 Answer

2005 Chevy Colorado drivers side window, and power locks


Check for door ajar switches not making contact.

Mar 08, 2010 | 2006 Chevrolet Colorado

1 Answer

Power windows and power locks wont work


Check your fuses first. Then check for power at the switches, and power from the switches to the respective solenoid and motor. Most likely it's fuses. Also check where the wiring runs through the door into the car for bare spots in the wiring that might have blown the fuses.

Jan 21, 2010 | 2004 Mitsubishi Endeavor

3 Answers

Power window on driver side stopped working and the door locks stopped working . Also this morning the battery was dead but nothing was left on.


It sounds like you may a faulty door lock switch. If you pushed the switch to lock the doors and the switch stuck and kept door lock solenoids energized, that would drain the battery. It would also keep the door locks from unlocking, as to why window don't work it could all be on the same fuse or circuit breaker. Usually the power windows are on an automatic reset circuit breaker. Do you hear click and a short time later another click (with the battery charged)? If so that the circuit breaker tripping then resetting. Good luck!

Dec 19, 2009 | 2005 Chevrolet Colorado

1 Answer

Camry 1996 automatic power lock doen't work, but windows work.


if you can here relays when unlocking/locking check for power at door lock actuators inside doors, if you have power on lock/unlock and good earth from connector actuators are faulty.
if no power on test light when operating check output from central door lock module while operating, none coming out of module then it might need replacing.
check 30Amp power fuse for main relay under bonnet (which goes to pin 8 white/blue on module)and 10Amp gauge fuse in cab(pin 1 blue/red on module),pin 15 is also power when relay is on(red/blue) with test light, and module/ actuators.
check outputs from module pin 3 & 4
blue/red
blue/black
that go to door locks

Jul 20, 2009 | 1996 Toyota Camry

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,488 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...