Question about 2005 Infiniti FX35

1 Answer

Trying to remove drivers door panel

On bottom of door handle small hole. I know there's some type of screw but can not see into hole is it phillips, flat head or is it some thing else thats holding the door panel ?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 1,986 Answers

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Posted on Aug 14, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Doorhandle


for passenger side:
1. unclip screw cover 'center flap' of inside door opener plastic cover, flap is 3/8"x 3/8" (center of plastic cover)
2. remove phillips screw now showing
3. push fabric panel (edge of door opener plastic cover-at hinged end of chrome handle) to allow uncliping of edge of plastic cover (top rt & lwr rt (for passenger side) of plastic cover)
4. open chrome inside door handle to allow plastic cover to be removed-slide plastic cover toward rear, free end of door to remove cover
5. remove switch panel-gently pry with wide non maring pry bar (cover wide blade screwdriver using cloth) do rear of sw panel 1st (don't pry front edge)
6. slide switch panel toward rear to allow removal
7. remove large phillips screw under sw panel
8. remove the 2 plastic covers near top, hinge edge -use plastic spoon handles to encourage caps to pop off. May also require small screwdriver approx 1/8" in to complete pop off
9. remove the 2 phillips screws w/ captive washers
10. remove 3 phillips/hex screws along the bottom inside of door panel
11. on outside/rear edge of panel push the 2 center pins of each in about 1/8"-this allows the clip to be pulled out w/ pin pushed in
12. remove plastic cover (REAR OF SIDE MIRROR)-pull window edge up and back.
13. lift rear of door panel (not hinge edge) up allow hinge edge to pivot around lower pin in door (hinge edge)
14. remove the 2 rt edge "L" brackets (gently pry center plastic pin out) (note the color and replace as removed)
15. slowly peel the clear plastc away from the non hinged end to expose the plastic panel with 3 phillips head screws
16. remove the 3 screws and panel for access to door handle.
17. using access area now available unlatch the rod attached to exterior door handle (unclip plastic to rotate clip up to allow rod to slide out-toward hinged edge)
18. using access area now available remove rod from ext door handle from inside door area
19. remove the 3 -10mm head bolts
20. remove the ext door handle (bottom edge out first)
reverse order to replace door handle

Mar 24, 2014 | 2003 Toyota Avalon

Tip

How to change a door speaker in a 2002 Dodge Ram pickup


This is definitely something you can do yourself. Dodge has made it pretty easy to accomplish this with a small amount of tools.
Tools Required:Phillips head screw driver;T-30 sized Torx bit (looks like http://en.wikipedia.org/wiki/File:Torx-Bits_T15-T20-T25-T30.jpg)
Disassembly:First, remove the 2 screws on the bottom of the door, there's one on the left and one on the right.
Then, remove the screw in the small triangular piece of plastic on the top-front of the door panel. This small piece of plastic looks like it's connected to the window, but it's not. The Infinity brand name may be on this piece, if you've got the Infinity speaker system.
The last of the phillips head screws you need to remove is in the middle of the panel, directly behind the door handle.
Now, grab your Torx bit and we're going to remove the door handle. Pull the door handle up, like you're going to open the door, and you should be able to fix your driver behind the handle and unscrew the bit. The door handle should be completely off now.
Next, pull up on the door panel and you'll feel the hooks securing it to the door release. You'll have to pull all the way up and out. Sometimes it will feel stuck and that's because the door lock fist snugly in its hole.
When the door panel comes loose from the door, you'll have to stick your hand behind the panel and disconnect 2 wires running to your control panel (for windows, locks and mirrors). This is done by just pressing the tab on the connector and pulling down. This should not be extremely difficult to remove.
Now that the door panel is free and clear, remove the 4 screws from the speaker and pull it out. There is another connector running to the speaker you will have to disconnect.
Take your new speaker, connect it where you disconnected the old one and put the screws back in.
Re-connect the window and lock connections coming out of the door to the door panel.
Slip the door lock back through it's hole in the panel.
Press the panel against the door tightly and pull the panel downward, the entire panel should feel secure against the door. If it does NOT feel secure and tight all the way around, then pull the panel back up and try it again.
Once the panel's back on, put the screws back in and re-attach the door handle.
Enjoy the music!

on Feb 28, 2011 | Dodge Ram 1500 Cars & Trucks

1 Answer

Remove door panel


Trim and molding remove tool and a phillips screw driver
Drivers Side

Remove
Door trim panel and water shield (top where window is)
Plastic panel around door handle. snaps out
1 screw upper front extension assembly (plastic triangle)
2 screws located lower bottom left (drivers side) and door trim panel
Use remove tool to push out retaining 'C' clip behind door handle
Grasp panel where opening are and pull up and out gently
Now disconnect wire harness

May 07, 2013 | 1991 Ford Thunderbird

1 Answer

Removing rear interior panals


Remove one Phillips screw from leading edge of door panel (near latch). Remove small cap behind the door handle, inside another Phillips screw - remove screw and then the cup behind the handle. Look down in arm rest and there is another Phillips screw. Last screw is behind the approximately 1 1/2 inch plug on front upper corner of panel. At this point, gently pry around lower edge and sides - there are either five or six clips pressed into the door frame. Once all are disengaged, gently swing the bottom of the panel out and lift off the top edge of door next to window opening. Once panel is off door, gently remove the control plug from the door lock/window control on the rear of panel. Install in reverse order
hope this helps

May 04, 2013 | 2005 Mazda Tribute

1 Answer

Need to take off door panel to put mirror on, how do you take off?


emilyandtodd, To remove the door panel you need to run your hands all around the panel to find any screws that are holding it. Remove any screws and look in the door handle where your fingers go when closing the door. There is usually a hidden screw in there. (Hidden by a little plastic cover smaller that a penny, remove the cover with a small screw driver) Sometimes there large screws around the handle itself. Look for any holes that will have phillips head screws in them. Sometimes there are lights in the door. Remove the lens and look for any screws. Also, at the door handle there is a plastic cover that can be removed with a small screwdriver and usually hides a screw. The panel is now held in by plastic push pins that are not visable until you pull the panel off. Starting at the bottom pull the panel from the door. You may need a little force here. When the panel is free from the bottom of the door pull it straight up and disconnect any wires going to the door. You will see a metal rod going to the door opener handle. This is locked in place by a plastic clip. Unlock the clip and pull the rod out. The panel should now be free. At the top, front of the door you should see a rubber insulator. Remove the insulator and there are three 10mm nuts holding the mirror in place. Remove the nuts being careful not to drop any inside the door. Remove mirror. Reverse procedure for replacement of any parts removed. Good luck with this.

May 08, 2011 | 2008 Chrysler Town & Country

1 Answer

My door handle from inside of passenger side is broke. How do I get the panel off?


Park the vehicle on level ground and have good lighting available. Open door all the way. Start with a pick, pocket knife or very small slot screw driver. Practically all modern vehicles utilize plastic snaps to secure the perimeter of a door panel. However, you will find that two large screws will hold the door panel on around the "door handle/arm rest" as this is where we pull the door closed....so it needs extra securing. If you look on the bottom portion of the handle, you will see either two access holes pointing up at a 35 degree angle...or two "plugs" which act as "appearance covers" hiding the actual holes. Carefully pop these out. Shine your flash light up the hole and identify the type of fastener. ( it i'll be a large Phillips # 3.....or a torx type fitting) remove these. Now, the other places to look for fasteners you remove from "your side of the door" are at the door handle "lever" remove the cover directly behind this lever. You might find this fastener also has a "beauty cover" remove it and the screw. next, top corner up by the outside mirror. you will have a speaker or a cover there that serves as the cover for the screws that mount the outside mirror. remove the cover. if you see no fasteners or covers, it likely pops off. Just be slow and careful. along with the big screws at the door handle/arm rest, there may be another fastener at the top of the handle. With all of these removed and if you see no fasteners around the bottom of the door...wedge your fingers along the bottom and pull straight out. You will be "unsnapping" the plastic fasteners at the bottom and sides of door. Now you will have a door panel that is loose at the bottom and away from the door frame itself. Barring any trim thats not part of the door panel, you should be able to raise the door panel strait up^^^ and free it from the top of the door. Remember, if its not coming off in a reasonable manner, something is still connected. Once the panel is free, sitting on the edge of the seat, put the door panel in your lap and disconnect the electrical connections, door lever rod...etcetera.....

Write me back and let me know how you did

Theroadisalover

Dec 31, 2010 | 2009 BMW X5

1 Answer

How do I remove the front interior door panel polo 1400 1999


You'll need a torx bit for the bottom screws. The door handle comes apart (using a screw driver) to expose 2 phillips screws holding the door handle to the door, after you get those out, pop the rest of the push clips out by firmly pulling on the door panel near the bottom, There may also be another screw on the TOP Front (near the mirror) very small phillips. Once you have the door panel loose, lift UP on the door panel to remove. Once you get that panel off, you'll have to remove all the other screws to get the window regulator out (lots of 10mm bolts). Unclip / unconnect the connections etc..

Jun 25, 2009 | 1999 Volkswagen Golf

1 Answer

Trying to remove drivers door panel on FX35


I would suspect that is a phillips screw. There may be another one in that area -- maybe not.

Removing this screw should allow yu to remove the door panel.

May 29, 2009 | 2005 Infiniti FX35

1 Answer

Procedure for removing door panel on passenger side 1994 camry


Sure.

Pull off the triangle thing.
On the door, at the front edge, there should be 2 plastic caps. Remove them. Under the caps there are screws. Remove them.
On the rear of the door panel, above the latch, are 2 round things, with a smaller round thing in the middle. Press on the inner round thing, and pull the pin assemblys out.
Do you have a light on the door panel at the bottom? If so, pry it out with a small screwdriver (it's just a "press-fit"), and remove the wire connector.
Under the arm-rest, remove the big phillips screw that is hidden, about an inch back from the outer edge of the panel. You will see the hole.
Under the arm rest, remove the tiny plastic trim cover, remove another big phillips screw.
Remove the door handle: Remove the phillips screw. Slide the handle forward or backward to release it from the door metal. Undo the clamp from the lock rod to the handle.
Remove any screws at the very bottom of the panel, if there are any.
Starting at the bottom of the panel. pull straight out, to defeat the plastic clamps tht holds the panel to the door metal. Once the panel is loose, pull it up a bit to remove it from the window opening retainer. Finally, inside the panel, unplug the wiring harness to the window switch assembly.

If you need any more info, please comment back. And, Thanks for the FIxYa.

Nov 14, 2008 | 1994 Toyota Camry

2 Answers

Removing inter door panel


Unscrew the armrests first.

Then you will see a few (i don't recall but i think there's 2) 5/16 sized screws under that.

The rest of the door panel is held on with plastic clips, which will most likely break, so be prepared to buy a few of them. You can gently "tug" on the door panel, starting at a corner and use a small flat head screwdriver, or a putty knife to pop out the clips.

Jun 01, 2008 | 1994 Chevrolet S-10 Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

453 people viewed this question

Ask a Question

Usually answered in minutes!

Top Infiniti Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14337 Answers

Are you an Infiniti Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...