Question about 2004 Nissan Quest

1 Answer

How do i turn off the tire pressure warning light all tires are 35psi

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

Bump them up to about 38 and it should go off.

Posted on Apr 28, 2009

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 416 Answers

SOURCE: Extreme cold weather has caused my tire pressure

my reset after driving for a bit if not check owner book

Posted on Jan 20, 2010

  • 88 Answers

SOURCE: The low tire pressure indicator

Pressure has to be the same in all tires.Check what tire pressure should be on sticker on pass door.
Some spare tires have sensors in them and so check spare tire,it should be the same as other tires if it is a fill size spare.There also might be a reset button under dash,check owners manual.If all this won't work there might be a bad wheel sensor.You will need to take car to a tire shop Good luck

Posted on Dec 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i reset the chime warning very low tire on a lincoln aviator 2003


most often refill tires to spec (35psi) make sure all tires are same pressure then must drive at 40mph or faster til light or chime goes off

Sep 08, 2014 | 2003 Lincoln Aviator

1 Answer

Tyre Pressure and ABS


By operating the tire pressure warning system reset switch, tire pressure warning system ECU can be set to issue a warning at an inflation pressure that corresponds with the type of tires.
Operate the tire pressure warning system reset switch only after the inflation pressures of all 4 tires have been adjusted on the vehicle.
To initialize the system, press and hold the tire pressure warning system reset switch for 3 seconds or longer with the power switch turned IG-ON. When starting the initialization, the tire pressure warning light blinks 3 times at 0.5 Hz.
During the initialization, the tire pressure warning system valve & transmitter measures the inflation
pressure of the tires, and registers the signals that are transmitted into the ECU at a frequency of 1 per
minute. The initialization process is completed when the signals from the tires have been received.
Once the tire pressure warning system reset switch has been pressed, do not turn the Ignition switch OFF for a few minutes.

Mar 05, 2014 | 2002 Toyota Corolla

1 Answer

Low tire pressure warning on 07 Chevy equinox


Now you need to go to a tire store,
to have you TPMS System problem resolved

Jun 25, 2012 | Chevrolet Equinox Cars & Trucks

1 Answer

Tyre pressure warning light showing when pressures are correct


Hi, the tire pressure monitor detects any changes in the tire inflation pressure. Therefore, it must initialize and store it in its memory if the tires or wheels have been replaced, re-inflated or the tires have been rotated. You can re-initialize the system by following these steps:

1. Check and make sure that your tires are inflated to the correct pressure

2. Turn the ignition switch to the ON position. If the low tire pressure warning light comes on, push and hold the tire pressure warning reset switch (in the glove box) until the warning light turns off and then release the switch.

3. Now press and hold the tire pressure warning reset switch until the low tire pressure warning light blinks three times.

4. Initialization is *not* completed until driving at the vehicle speed of 19 mph or over for more than one hour. the tire pressure monitoring starts when initialization is completed.

May 13, 2011 | Renault 18I Cars & Trucks

1 Answer

What is the correct tire pressure for a mazda tribute with these tires 245/70/R16


First of all, don't exceed the maximum pressure that is marked on the tire.
Most cars have the tire size and tire pressure listed on a tag on the inside of the front door or the door jam. Usually the driver's side.
If you can't find the "official" tire pressure on the door or the owner's manual, you are pretty safe using between 30 and 35psi. I keep my 2002 Escape at 35psi.

Apr 15, 2011 | Mazda Tribute Cars & Trucks

1 Answer

Changed right front tire now reads zero on dash light is on


Your tire pressure monitor needs to be reset whenever you change or rotate your tires...

1. check and make sure that your tires are inflated to the correct pressure

2. turn the ignition switch to the ON position. If the low tire pressure warning light comes on, push and hold the tire pressure warning reset switch (think the switch is in the glovebox, but not sure) until the warning light turns off and then release the switch.

3. now press and hold the tire pressure warning reset switch until the low tire pressure warning light blinks three times.

4. initialization is *not* completed until driving at the vehicle speed of 19 mph or over for more than one hour. the tire pressure monitoring starts when initialization is completed.

Aug 24, 2009 | 2008 Chevrolet Tahoe

1 Answer

How do you reset low tire light


1. check and make sure that your tires are inflated to the correct pressure

2. turn the ignition switch to the ON position. If the low tire pressure warning light comes on, push and hold the tire pressure warning reset switch (think the switch is in the glovebox, but not sure) until the warning light turns off and then release the switch.

3. now press and hold the tire pressure warning reset switch until the low tire pressure warning light blinks three times.

4. initialization is *not* completed until driving at the vehicle speed of 19 mph or over for more than one hour. the tire pressure monitoring starts when initialization is completed.

Aug 20, 2009 | 2005 Chrysler PT Cruiser

3 Answers

The check tire pressure light and ABS auto traction sensor light keep coming on. Tire pressure is good


The tire pressure monitor detects any changes in the tire inflation pressure. Therefore, it must initialize and store it in its memory if the tires or wheels have been replaced, re-inflated or the tires have been rotated. You should be able to re-initialize the system by following these steps:

1. check and make sure that your tires are inflated to the correct pressure

2. turn the ignition switch to the ON position. If the low tire pressure warning light comes on, push and hold the tire pressure warning reset switch (think the switch is in the glovebox, but not sure) until the warning light turns off and then release the switch.

3. now press and hold the tire pressure warning reset switch until the low tire pressure warning light blinks three times.

4. initialization is *not* completed until driving at the vehicle speed of 19 mph or over for more than one hour. the tire pressure monitoring starts when initialization is completed.

Aug 11, 2009 | 2004 Cadillac Deville

3 Answers

Tire pressure sensor fault goes on while driving


Tire pressure always changes...
when you drive your vehicle for a long period of time the tires' temperature goes up along with the
pressure in your tires, the molecules in the air inside your tires get excited (hot)
when your vehicle is immobile for a while your tires' temperature goes down along with the
pressure in your tires, the molecules in the air inside your tires get compacted (cold)
This is the best time to get a true PSI reading from your tires....
the recommended tire pressure on most tires should be set at 35PSI
But there might be a problem with your sensors, I work with TOYOTA their sensors are set up to
where when the PSI on your tires drops below the 35PSI, the tire pressure light would then
come on.
You should also check if your spare tire comes equipped with pressure sensors, which in most cases
they do, depending on the type of tire the PSI on spare tires will usually range from 35PSI- 80PSI
you can check your owners manual for this, or simply read the recommended PSI written on the
tire.

Mar 05, 2009 | 2005 Mercury Mountaineer

1 Answer

How do I keep the tire warning light from coming on during travel? 2006 nissan frontier king cab LE


make sure all your tire pressures are above 35psi. the light will come on if your tires are below 28 psi. check all your tires for tire pressure. if pressures are low, add air and drive truck at 35+mph for about 1 mile and the light will go out unless you have a sensor problem, but fotha the light will be flashing. so to sum it up, check your tirpressures and make sure, that you have 35 psi in all 4 tires.

Jul 29, 2008 | 1998 Nissan Frontier

Not finding what you are looking for?
2004 Nissan Quest Logo

199 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

713 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...