Question about 2004 Ford F350

1 Answer

Driver's side electric window panel

I just purchased an F-350 and the windows will not work from the panel on the driver's side door. They will work from the individual door.

Posted by on

  • 2 more comments 
  • annec56 Apr 14, 2009

    The drivers window works and each window works at the individual door. I cannot operate the other 3 windows from the master panel on the driver's side door.

  • annec56 Apr 14, 2009

    The other windows will not work in either direction up or down from the drivers switch.

  • Chuck Martin
    Chuck Martin May 11, 2010

    the other windows will not work in either direction up or down from drivers switch?

    Just trying to make sure I understand because the way the system works is the other 3 windows are feed from the drivers master switch.Usually when you have what you are describing it usually is a wiring concern and the windows will work in one direction but not the other from the drivers side.

  • Chuck Martin
    Chuck Martin May 11, 2010

    Does the drivers window work?

    Can you roll the other windows up from drivers side?

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Ford Master
  • 783 Answers

It has to be a bad master window switch.
See power and ground is supplied thru the master window switch to the other switches. When you press the switch it is routing the power and ground to the window motor. For instance in the up position at the motor the left wire may be hot and the right ground and in the down position it will be opposite.
So if they are working from the individual doors then the wiring has to be good and the switch has just lost it's ability to route it where it needs to go.

Posted on Apr 14, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My passenger side electric window stopped working on my 1991gmc sierra 1500. The passenger side switch panel don't work for the window but works for the lock. Driver side master switch doesn't work for the...


The odds of both switches going bad at the same time is high, remove the door panel and tap on the window motor with a hammer, while trying the switches. I may have jammed up. Ground a test light and check the motor connection, while trying the switch, power will show on either side depending on if it turning up or down

Mar 19, 2015 | Cars & Trucks

1 Answer

Can't operate electric window on driver's side door


The door panel will have to come off. check for a bad motor or wiring to motor, or a bad drivers side switch. check the fuses first! and is the drivers side window locked on drivers side, just push the unlock window from the master controls on drivers side to see if it works. on my car, the drivers side window would not work. I accidentally hit the window lock with my arm. God-Bless!

Jan 29, 2015 | Cars & Trucks

1 Answer

The driver side electric window on my hyundai 2004 santa fe won't open


The fuse is not the problem there is no driver side fuse it is prob the connection where the wiring connects to the window up and down switch. You have to remove the door panel careful not to tear the sound deadener sheeting. You have to first remove the screws and pry the retaining clips with a special trim panel removal tool U can purchase from auto parts store, work slowly and carefully around the outer edge of the trim panel until its free. Then clean the connections between the wiring contacts. Reverse to reinstall door panel trim. Hope that Helps

Jan 02, 2014 | Hyundai Santa Fe Cars & Trucks

2 Answers

I need help with replacing the driver side window in a 2003 ford f-150,four door super crew cab truck.


Removal & Installation
Motor - Front Door
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove the window control switch
  3. Remove the front door trim panel and watershield.
  4. Tape the window in the full UP position.
  5. Disconnect the window motor electrical connector.
    NOTE Support the window motor while removing the window motor retaining screws.
  6. Remove the window motor bolts and remove the motor.
  7. To install, reverse the removal procedure.
Rear Door
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove the window control switch.
  3. Remove the rear door trim panel and the rear door trim watershield.
  4. Remove the door speakers.
  5. Tape the window glass in the full UP position.
  6. Disconnect the window regulator electric drive.
  7. Position the connector for the window regulator electric drive inside of the door.
  8. Remove the bolts.
  9. Separate the window regulator electric drive from the rear door window regulator.
  10. Remove the window regulator electric drive from the door.
  11. To install, reverse the removal procedure.

Motor & Regulator

3d4a07e.jpg

Fig. Front Door Trim Panel

7932e42.jpg


Fig. Rear Door Trim Panel-Crew Cab


Regulator - Power Windows

506866e.jpg

Fig. Window regulator arm nuts


db15984.jpg

Fig. Window regulator bolts

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove the window control switch.
  3. Remove the door trim panel.
  4. Remove the door speaker.
  5. Remove the door watershield.
    NOTE Do not remove the window glass from the door.
  6. Remove the window glass from the window regulator.
  7. Tape the window glass in the full UP position.
  8. Disconnect the window motor electrical connector (power windows only).
  9. Loosen the window regulator arm nuts and pull the arm from the mounting position.
  10. Loosen the bolts and remove the window regulator.
  11. To install, reverse the removal procedure.

Hope helped with this. Good luck.

Nov 16, 2009 | 2003 Ford F150 Regular Cab

3 Answers

2000 Buick Lesbre - Intermittant electrical: Door


THE PROBLEM SOUNDS LIKE LOOSE WIRING CONECTIONS IN THE DRIVERS DOOR , BEST THING TO DO IS HAVE A LOOK OPEN UP DOOR PANEL AND CHECK ALL CONECTIONS, GOOD LUCK

Oct 22, 2009 | 2000 Buick LeSabre

1 Answer

Fallen driver's side window


probably need a new window regulator. ebay. 93 to 98 should fit.

Section 01-05: Trim, Interior 1998 Villager Workshop Manual
REMOVAL AND INSTALLATION Trim Panel(s), Door Front
Removal
  1. Disconnect the battery ground cable (14301) if equipped with power locks or power windows.
  1. swv~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use care when removing the front door inside handle escutcheon (22620). Failure to do so can result in damage to the component.
    Carefully pry off the front door inside handle escutcheon by inserting a standard 1/4 inch screwdriver between the top rear portion of the front door inside handle escutcheon and the front door trim panel (23942) .




  1. If equipped with manual windows, slip a clean shop rag between the window regulator handle (23342) and the front door trim panel .
  1. Pull the shop rag back and forth to release the window regulator handle clip.




  1. Remove the three cover caps and front door trim panel screws.
  1. Remove the one front door trim panel capped screws from the door pull handle.
  1. If equipped with power windows, remove the door pull handle. Disconnect the electrical connectors.
  1. Slide a flat-bladed tool behind each of the retainers and twist the tool to disengage the front door trim panel from the front door (20124) .
  1. Remove the front door trim panel.
Installation
To install, reverse the removal procedure.
---------------------------------------------------------
Window Regulator, Power Front Door
Removal
  1. Disconnect the battery ground cable (14301) .
  1. Remove the front door window glass (21410) . Refer to the front door window glass removal procedure in this section.
  1. Remove the two front door brace bolts and the front door brace.


    415712f.gif

  1. Disconnect the front window regulator electric drive electrical connector.
  1. Remove the four front door window glass regulator track bolts.

    67b6136.gif


  1. Remove the three front window regulator electric drive bolts.
  1. Remove the front door window glass regulator track and the front window regulator electric drive (23394) as an assembly through the opening in the front door (20124) .
Installation
  1. Install the front door window glass regulator track and the front window regulator electric drive as an assembly through the opening in the front door .
  1. Install the three front window regulator electric drive bolts. Tighten the front window regulator electric drive bolts securely.
  1. Install the four front door window glass regulator track bolts. Tighten the front door window glass regulator track bolts securely.

Apr 29, 2009 | 1998 Mercury Villager

1 Answer

Drivers side electric window does not work


Remove the door panel and disconnect the motor from the window, but leave it plugged in. See if the motor works. If it does you should grease the tracks on the window. If the motor does not work then you should replace the motor. The motor will probably get hot when you try working it.

Jan 23, 2009 | 2005 Nissan Xterra

1 Answer

All of a sudden the driver side window will not roll up.


is it electric windows? if it has electric windows does the passenger window roll up using the switch for it on the passenger door panel? if it works on the passenger door panel and not on the driver's door panel , then your switch on the drivers door panel is bad... replace it.

Oct 13, 2008 | 1999 Oldsmobile Cutlass

1 Answer

My drivers side electric window won't work


Hi Hawkeye1973

The first thing you should do is swap the passenger switch in place of the drivers switch and then see if the window now works. If so then you need a new drivers side switch. It may be clicking but it may not be working.

If it still doesn't work then you need to get your hands on a volt meter and get back to me.

TULL FAMILY
You need to remove the drivers door panel and investigate the window mechanism, it sounds asthough its sticking.

Very best regards

Geordie

Jun 19, 2008 | 1996 Ford Escort 4 Door

Not finding what you are looking for?
2004 Ford F350 Logo

Related Topics:

293 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...