Question about 1994 Oldsmobile Cutlass Supreme

1 Answer

Brakes on 1994 cutlass keep running tight

The brakes on my 94 olds cutlass keep self tighten. I can stop car pump brakes 40 times and drive car sometimes 20 miles, sometimes less than 5. I hav bleed the system 3x, but brakes do the same thing . I brought a GM scan tool but it doesn't work on the 94 cutlass. will I have to go to a dealer or can I buy a scan tool for this car?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,055 Answers

Youve got a bad mastercylinder

Posted on Apr 14, 2009

Testimonial: "Thanks changed master and wheel cylinders."

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you tighten waterpump pulley on 94' buick


How to Change a Water Pump on a 1994 Buick Park Avenue. ... Thread all the bolts onto the pump finger tight, then tighten the short bolts with your wrench in ... www.ehow.com/how_7471017_change-1994-buick-park-avenue.html
hope this will help

Jan 26, 2012 | 1994 Buick Century

1 Answer

I ran my car with old gas (2 years old) then it stopped running. I have changed the gas,plugs .the self diagnostic system check came up with code 12 problem with standby memory circuit.I could use any...


The old fuel could have clogged the fuel filter, pump, lines and/or injectors. I'm not sure about the code on your model but I believe it refers to the circuit that supplies power to keep your radio presets and clock set when the ignition is turned off.

Mar 11, 2011 | 1994 Plymouth Sundance

1 Answer

Added brake fluid when pedal went to floor,reservoir almost dry,good brakes after that pumped them up, now maybe 1 month later lent same car to friend ,said brake pedal sank to floor & red brake light...


There is diffinatly a leak in the break system and it is most likely one if not both of your rear wheel cylinders. Need to have it checked out before it gets worse and you end up in a wreck due to no brakes.

Jan 08, 2011 | 1994 Oldsmobile Cutlass Supreme

1 Answer

'94 Olds Cutlass Supreme Door Handles


You have to find the linkage and pull it. If yu cannot find the linkage, one trick is to go to a self serve wrecking yard and play with one of the 90s olds by removing the door panel and looking at it to see how it works.

Apr 05, 2010 | 1994 Oldsmobile Cutlass Supreme

1 Answer

How do i change the front brakes on a 1991 oldsmobile cutlass ciera. i already have the brake paids


Hello, open the hood locate your brake fluid take the top off, than you want to losen the lug nuts one the wheel enough so they turn by hand. Jack up the car high enough to get a jack stand under it and the wheel is off the ground. Once the car is supported securely remove the lug nuts and wheel. Once the wheel is removed remove the screw on the bottom of the brake caliper, remove the old pads. Rotate the caliper upward, using a C-clamp and a old brake pad push the piston back in the caliper. Position the old brake pad to cover the piston and the C-clamp in the center of the old brake pad and slowly turn till the piston is fully retracted in the caliper. Install the new pads, put the caliper back in position, put the caliper screw back in double check work. Once every thing looks ok put the wheel back on, only hand tighten the lug nuts, make sure the wheel is tighten evenly. Remove jack stand, lower the car tighten the lug nuts using a crossing pattern once that is done pump the brakes, till they get firm, after they get firm start the car pump the brakes a few more times. The fun part take it for a test ride but allow your self more than normal distance to stop.

Feb 14, 2010 | 1991 Oldsmobile Cutlass Ciera

3 Answers

94 Old Cutlass Ciero 3.1 engine starts and dies won't stay running


Replace the oil pressure switch next to the oil filter. When you turn on the ignition the fuel pump runs to prime the system then turns off. Then the oil pressure switch runs the fuel pump to keep the engine running. To test, connect the fuel pump test wire(located at the left front wheel well) to the battery. This will bypass the pressure switch and the engine should run.

Jul 12, 2009 | 1994 Oldsmobile Cutlass Ciera

1 Answer

94 cutlass ciere wont start


check out fuel pump relay and oil sending unit for oil leak oil sender is made to cut out fuel pump apon oil pressure failing

Jun 30, 2009 | 1994 Oldsmobile Cutlass Ciera

1 Answer

Tighting an emergency brake


I believe the 94 Sunbird's have rear emergency brakes. The rear brakes are drum brakes and it's very hard for them to lock up but should slow the car down to a stop and hold it from moving when at a stop.
The way they work is, the emergency brake cable pulls on the one of the brake shoes to the brake drums on each side so you only have 50% of your braking power to start with.
If your brake's are not holding when it's at a stop position, the brake shoes are warn or glazed over and need to be replaced. 
You can try adjusting then by backing up a few times like say 7 times and giving it full brake application. That should adjust the brakes if the self adjusters are still working.
Good luck and hope this helps

May 06, 2009 | 1994 Pontiac Sunbird

1 Answer

Just got 94 olds with 3.4 ltr how realiable are


No major problems, they are a little harder to work on than the 3.1. The Alternator is in a real tight spot and they have a timing belt that needs replace every 90,000 miles. Even though you don't have 90,000 miles on yours, I would recommend replacing the belt if it hasn't been done. Just because it is 15 years old .

Mar 05, 2009 | 1994 Oldsmobile Cutlass Ciera

Not finding what you are looking for?
1994 Oldsmobile Cutlass Supreme Logo

Related Topics:

184 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8548 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...