Question about 1985 Nissan Pickup

Open Question

I have a 1981 Datsun Stanza with the L18 engine, but the 2 SU carbs is giving problems, will a CA20 carb work on the L18 engine?

Posted by on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 599 Answers

SOURCE: Contact Point Gap 1981 Datsun Stanza

cool old car :)...set points at .019 in. new ...and .016 if using used

Posted on Nov 10, 2008

ZJLimited
  • 17970 Answers

SOURCE: I need the firing order

For 1984 Nissan Stanza (USA) 2.0 liter SOHC L4 (CA20S) check...

zjlimited_242.gif


Hope this helps (remember to rate this answer).

Posted on Mar 14, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

HOW TO REPAIR THE CABURETOR


Some carbs are simple and some complex but both should be treated the same way.

Remove the carb and thoroughly wash the outside before turning each adjuster screw in and carefully counting the turns until it bottoms (eg 2.75) so the screw can be returned to the original position.

Most carbs need only thorough cleaning and few, if any, new parts.

The carb should be systematically and completely dismantled making drawings and notes during the process and then each component is thoroughly cleaned ensuring all air and fuel passages and jets are clear and use the reverse process to reassemble.

During the cleaning process each component should be examined for wear or damage using a magnifier and replaced if necessary. It is usually wise to replace the float valve and any flexible diaphragms but this isn't always necessary. If water is found inside the carb the fuel tank should also be cleaned.

Jun 29, 2017 | Cars & Trucks

1 Answer

What can make a Nissan z24 engine give bad noice and how can it fix


1986 Nissan 720 King Cab with 2.4 Naps Z engine (Carb ...

community.ratsun.net > Technical > Engine

Jul 1, 2009 - 14 posts - ‎5 authors
1986 Nissan 720 King Cab with 2.4 Naps Z engine (Carb based) ... Just yesterday it made a real weird loud panging noise (Kind of ... If you dont surface the head it will usually form better to the bad block deck giving you as much as another 100k !!!!!!!! before it ... Also the z24 HATES head gasket coating.

Idle problem? - Engine - Ratsun Forums - Ratsun.net

community.ratsun.net > Technical > Engine

Nov 17, 2009 - 14 posts - ‎6 authors
I am new to this forum along with Datsun/Nissan trucks. ... doing a lot of reading and trying to become more familiar with the Nissan 720 /z24 engine. ... also if the mixture is out of adjustment it can cause the same symtoms also.the ... Listen near the back of the carb and you should hear a light clicking sound.

nissan hardbody engine rattle - YouTube



Dec 03, 2015 | Nissan Cars & Trucks

1 Answer

1981 Laredo. Where can I get a vacuum line routing and connection diagram?


very very old post
ok i figured your old post out.
you posted a 1981 SJ jeep to jeep grand cherokee section.
this is the early Cherokee and is not grand. 1995+
with no engine stated, wow)
ill not try to guess the engine.
here they are...
258 cu in (4.2 L) AMC I6
360 cu in (5.9 L) AMC V8 2-barrel
360 cu in (5.9 L) AMC V8 4-barrel
401 cu in (6.6 L) AMC V8 4-barrel

made in USA or Australia, ill guess USA

the vacuum setups vary by carb used
and if FED usa or Calif USA setups
fed was called 49 state back when...
and there is the high altitude versions.
and std or HD cooling versions (huge list of vacuum setups, if you want look in alldata.com and behold.
omg one more the Canada version.... (ill skip export versions)
calif versions are huge complex....

so ill guess the 360 2 barrel,

e97fc71a-8109-4b75-9002-a238a4147964.jpg

Jul 08, 2014 | Jeep Grand Cherokee Cars & Trucks

1 Answer

My 1981 dodge p/u sits a sputters after it warms up you give a little gas it does it give it more gas it smooths out has a slant 6 one barl carb what do you thim=nk it may be i changed the fuel filter...


Try adjusting the idle/air screw on the carb. With the engine off, turn the screw gently to the right until it bottoms out. Don't screw to tight, it will ruin the seat. Turn it out 2 full turns and start the car. After revving the engine a couple of times,let it settle down to an idle. after it warms up, screw it in or out until you get the highest idle speed. If that doesn't do it, you will need to rebuild the carb.

Jul 22, 2011 | Dodge D150 Cars & Trucks

1 Answer

I need the firing order for a1984 nissan stanza--4cy--2.0---engine # CA20(e) 1974 RLF01A---FD33 Thanks


For 1984 Nissan Stanza (USA) 2.0 liter SOHC L4 (CA20S) check...

zjlimited_242.gif


Hope this helps (remember to rate this answer).

Mar 14, 2011 | 1984 Nissan Stanza

1 Answer

Contact Point Gap 1981 Datsun Stanza


cool old car :)...set points at .019 in. new ...and .016 if using used

Nov 10, 2008 | Datsun Stanza Cars & Trucks

1 Answer

Carburetor Datsun Bluebird


Here are two more choices if Recarbco doesn't help. Guaranteed Carbs. 1-800-250-8746 or www.importcarbs.com and Carburetor1 1-888-777-8208 or www.carburetor1.com. I have had good luck with both of these places for hard to find stuff. Good Luck.

Aug 31, 2008 | Datsun Maxima Cars & Trucks

2 Answers

Low idle speed


if you washed the engine bay theres a chance you may have got water into the spark plugs or on the distrubutor, remove dizzy cap and remove water from the underside, sum crc products work well at this. usually after the engine gets hot it will evaporate the water away, I hope you don't have an exposed air filter, this could also be wet causing starvation. sum more info would be helpful

Aug 08, 2008 | 2006 Datsun Stanza

1 Answer

Datsun stanza 1980 tappets (lifters)


This car has hydraulic lifters( tappets} therefore should not adjustment, you probably have a bad or weak lifter. But, in any case you have to remove the valve covers to make the adjustment. You will see the adjustable bolt on the rocker arm. rotate the engine until the valve is all the way to the top, [no tension on the valve spring] then place a feeler Gage in between the rocker arm and the valve stem, adjust the rocker arm until the feeler Gage is snug but not tight. Do this with each valve. Check the book for the correct Gage to use but I think it is a .018.

May 15, 2008 | 2006 Datsun Stanza

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

109 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

713 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...