Question about 1999 Mazda Pickup

2 Answers

99 nazda 2x4 pu standard- any adjustment on clutch? specially backing up.

Posted by on

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 232 Answers

No there isn't any adjustment,and if you have good pedal pressure there isn't any point in trying to bleed the hydraulic system.

Posted on Apr 14, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

How do you bleed theclutch hydraulic system

Posted on Jun 23, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where does transmission fluid go in a standard 99 Chevy metro? No one working on my car can figure out where to put the fluid back in at for the clutch. Please help me.


Need clarification, are we talking the actual fluid for the transmission, or the clutch slave cylinder fluid for depressing to engage the clutch on the transmission?

Feb 22, 2017 | Cars & Trucks

2 Answers

I have a 93 Toyota pick up 4x4 standard transmission. Sometimes when I go to reverse, there is a grinding noise, which won't let me shift into reverse. I then need to turn off the vehicle, then engage....


Could be the clutch.
Reverse and first do not have gears that line up like the others do. So if the clutch is not disengaging all the way, they will grind.

Dec 13, 2012 | Cars & Trucks

1 Answer

I have a 77 Toyota PU. New Clutch installed. Slave and throughout adjusted properly. Adjustment under dash adjusted full out. Still I have to jam the clutch all the way to the floor and barely able to get...


if it worked good before the clutch kit was installed , but not after then the clutch installation is incorrect
probably find the the clutch plate has been installed incorrectly
with a correctly fitted clutch kit , there is no necessity to change pedal height or anything else

Jun 23, 2017 | 1983 Toyota Pickup

1 Answer

1987 Nissan PU, I replaced the master and slave clutch cyls. I bleed the system and there is no air in the lines but peddle does not get hard. Could the new master or slave cyl be bad? I see you can adjust...


The shaft should come all the way back, when the pedal is back, the master shaft should be adjusted so there is very little play in the pedal. But it needs some play. Make sure you can see the slave cylinder move when you depress the clutch pedal, you will need help to operate the pedal, while you look.

May 10, 2010 | 1987 Nissan Pickup

1 Answer

Just bought 99 Hombre. My clutch pedal dose not work right


yes you can adjust the clutch unless it is already adjusted as far as it can be then you may have to replace it

Aug 30, 2009 | 1999 Isuzu Hombre

2 Answers

How do i bypass the clutch starter safety switch for my 99 Metro?


jumper the connector to the clutch safety switch at the top of the clutch pedal lever.

May 25, 2009 | 1998 Chevrolet Metro

1 Answer

Clutch problem


The rod at the end of the slave cylinder can be adjusted. make sure clutch pedal has no more than an inch and a half of free play. If free play is within the 1.5" & still have problem with clutch disengaging, chances are clutch is worn

Jan 03, 2009 | 1991 Toyota Pickup

1 Answer

My fan does not work in 87 pu


Please drop the glove compartment and you will see the fuses and relays to exchange...
That is for Toyota pickups....!!!!

Oct 06, 2017 | 1987 Toyota Pickup

1 Answer

Clutch adjustment


This is a hydraulic clutch, it is self adjusting, it sounds like you need to replace the clutch because it has adjusted out as far as it can. I think you are saying it slips when you try to accelerate, that most definitely means the clutch is worn out.

Nov 19, 2008 | 1988 Honda Prelude

Not finding what you are looking for?
1999 Mazda Pickup Logo

Related Topics:

84 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

79186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...