Question about 1988 Mazda B2200

Open Question

Timing marks for a fe 2.0 8v sohc engine

Cam pulley timing marks, the pulley has the letters 'A' rotate 1/4 turn then it has 'B', same again then it has 'C', then finally a lilttle dot [ which is 180* from 'B'.its currently set tdc bottom, and on 'B' on cam pulley, it runs like ****, unless i fully advance the dizzy. harmonic timing marks dont line up tdc either, about 20* btdc and no1 piston is at top compression.[weird] if i set bottom on tdc, no1 is already on the down stroke. im wandering if this engine has different model harmonic and cam pulley [not original to engine] or a different head, mazda ford, ford mazda. p.s, its not my car, its a mate who has tryed everything. it was a lpg/fuel. my honest opinon the timing is way out, valve timing etc coughs through the carb, and backfires. cheers

Posted by on

  • lyric_d Apr 20, 2009




    set cam timing, and tdc. found dizzy to be at fault, to much play between the gear and the rotor [ wasnt returning rotor while in place] so i wasnt getting a pin point spark. changed dizzy, vehicle runs fine. im still baffled about the tdc marks though. as its set roughly @ 20* btdc[ its gotta be a different harmonic balancer]


×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
tripletauto
  • 1450 Answers

SOURCE: Dome or Dish Pistons for Mazda FE3N 2L

The dome pistons will provide higher compression than the dished. the domed ones should have an eyebrow cut out for the valves. I believe you would be happiest going with the domes. you might run into spark knock with the increased compression

Posted on Nov 10, 2008

Ad
  • 37 Answers

SOURCE: 1991 mazda b2200- timing belt changed

The keyway and or the dot on the crank should be line at 12 oclock. You will see a point on the oil pump housing to go by. On the camshaft the pointer will be at 12 oclock also. Use the O on the camshaft to the top at mark. Be sure to look at the dist. roter to make sure that it is pointing at the #1 spark plug wire. I could get 180 out of time. If you do it right it should start up right away. then you can use a timing light to finish it.
Good Luck jerry1938@hotmail.com

Posted on Dec 13, 2008

flacooo1
  • 172 Answers

SOURCE: 1996 timing belt changed, lined up all the marks,

Hi my name is juan and lets try to solve this it is possible that when you rotated the camshaft the distributor last his position and this is why it won't start it may not be the problem but this happens a lot so open your distributor and aline up your marks on camshaft and the crankshaft then make sure the distributor is pointing near the #1 spark plug if is opposite give it a 1 more turn to the crankshaft line up your marks again and se what happens #1 spark plug is the closets to the front part of the engine on 4cil

Posted on Mar 26, 2009

Shiv_Jee
  • 87 Answers

SOURCE: gollf gti 8v 1997 missfire at 3000 rpm

Hi,

Try taking the wires coming from your distributor. and twist them around each other.that way they act like a homemade shielded cable. Like you said two wires running right beside each other act like a little antenna that’s what I had to do to a wheel speed sensor on a car when i worked at GM. I hope I said that to wear you can understand it

Let us know if that fixed your Car,

Thanks

Shiv.

Posted on Aug 23, 2009

  • 2 Answers

SOURCE: Which Mazda diesel engine do I have? RF, RF-CX or RF-N

The engine is a RF- CX the CX denotes comprex pressure wave supercgarger

Posted on Dec 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where do I find the timing marks on pulleys?


in the factory service manual FSM.

or

login to

alldata.com

and read all the steps



3VZ-FE (and 2vz)
this is your engine. and has many steps

key is timing and proper belt tension and is free running engine.



quote

Prior to timing belt removal, make sure all the match-marks are there-2VZ-FE and 3VZ-FE engines

less photos:

the crank mark is CR -line

the cam pulleys, 3v pulley to R-cam mark

and 3v pulley to L-cam mark. (photos are best).





  1. Remove the timing belt.


If the timing belt is to be reused, draw a directional arrow on the timing belt in the direction of engine rotation (clockwise) and place matchmarks on the timing belt and crankshaft gear to match the drilled mark on the pulley.



  1. With a 10mm hex wrench, remove the setbolt, plate washer and the No. 1 idler pulley.


  2. Remove the crankshaft timing pulley, if it can NOT be removed by hand, use two flat bladed tools. Position shop rags on the components to prevent damage.


TO INSTALL:



  1. Turn the crankshaft until the key groove in the crankshaft timing pulley is facing upward. Slide the timing pulley on so that the flange side faces inward.


  2. Apply bolt adhesive to the first few threads of the No. 1 idler pulley setbolt, install the plate washer and pulley and then tighten the bolt to 25 ft. lbs. (34 Nm).


  3. Install the timing belt on the crankshaft timing, No. 1 idler and water pump pulleys.


If the old timing belt is being reinstalled, make sure the directional arrow is facing in the original direction and that the belt and crankshaft gear matchmarks are properly aligned.



  1. Install the lower (No. 1) timing cover and tighten the bolts.


  2. Align the crankshaft pulley set key with the key groove on the pulley and slide the pulley on. Tighten the bolt to 181 ft. lbs. (245 Nm).


  3. Install the No. 2 idler pulley and tighten the bolt to 29 ft. lbs. (39 Nm). Check that the pulley moves smoothly.


  4. Slide the left pulley, facing the flange side outward. Align the knock pin hole of the camshaft with the knock pin of the timing pulley, then install the knock pin. Tighten the left camshaft timing pulley bolt to 80 ft. lbs. (108 Nm).


  5. Set the No. 1 cylinder to TDC again. Turn the right camshaft until the knock pin hole is aligned with the timing mark on the No. 3 belt cover. Turn the left pulley until the marks on the pulley are aligned with the mark on the No. 3 timing cover.


  6. Check that the mark on the belt matches with the edge of the lower cover. If not, shift it on the crank pulley until it does. Turn the left pulley clockwise a bit and align the mark on the timing belt with the timing mark on the pulley. Slide the belt over the left pulley. Now move the pulley until the marks on it align with the one on the No. 3 cover. There should be tension on the belt between the crankshaft pulley and the left camshaft pulley.


  7. Align the installation mark on the timing belt with the mark on the right side camshaft pulley. Hang the belt over the pulley with the flange facing inward. Align the timing marks on the right pulley with the one on the No. 3 cover and slide the pulley onto the end of the camshaft. Move the pulley until the camshaft knock pin hole is aligned with the groove in the pulley and then install the knock pin. Tighten the bolt to 55 ft. lbs. (75 Nm).


  8. Position a plate washer between the timing belt tensioner and the a block and then press in the pushrod until the holes are aligned between it and the housing. Slide a 1.27mm (3VZ-FE 1.5mm) Allen wrench through the hole to keep the push rod set. Install the dust boot and then install the tensioner. Tighten the bolts to 20 ft. lbs. (26 Nm). Don\'t forget to pull out the Allen wrench!


  9. Turn the crankshaft clockwise two complete revolutions and check that all marks are still in alignment. If they aren\'t, remove the timing belt and start over again.


  10. Install the right engine mount bracket and tighten it to 30 ft. lbs. (39 Nm).


  11. Position a new gasket and then install the upper (No. 2) timing cover. refer to the illustration for bolt positioning.


  12. Install the spark plugs.


  13. On the 2VZ-FE, install the right engine mount insulator. Tighten the bolt to 47 ft. lbs. (64 Nm), the bracket nut to 38 ft. lbs. (52 Nm) and the body nut to 65 ft. lbs. (88 Nm). Install the No. 1 stay and tighten it to 38 ft. lbs. (52 Nm). Install the No. 2 stay and tighten the bolt to 48 ft. lbs. (66 Nm) and the nut to 38 ft. lbs. (52 Nm).


  14. On the 3VZ-FE, install the control rod and tighten the bolts to 47 ft. lbs. (64 Nm). Install the right stay and tighten it to 23 ft. lbs. (31 Nm).


  15. Install and adjust the drive belts.


  16. Install the fender apron seal and the wheel.


  17. On the 3VZ-FE, install the No. 2 stay and tighten the bolt to 55 ft. lbs. (75 Nm), the nut to 46 ft. lbs. (62 Nm). Install the No. 3 stay and tighten it to 54 ft. lbs. (73 Nm).


  18. Install the coolant overflow tank and the washer tank.


  19. Install the power steering reservoir tank and the cruise control actuator.


  20. Connect the battery cable, start the car and check for any leaks.


end quote.

Feb 27, 2014 | 1993 Toyota Camry V6

1 Answer

Timing marks toyota 4e-fe


The detail is as under:
A. With the lower timing case in place and upper half timing case removed.
1. With the engine switch OFF, and in neutral position, hand brake pulled, jack up the right front wheel. Turn the steering wheel fully right hand side. Rotate the engine crankshaft pulley with 19 mm deep socket clock wise and bring the engraved timing mark of the pulley in front of Zero (0) degree mark which is printed on the lower timing case.
2. The cam shaft timing gear has a small hole on one of its spokes.
It should be straight upward, at exactly 90 degrees to the cylinder head upper face. With the help of mirror carefully look through this hole, you will find a pin hole mark there. With the crankshaft pulley at 0 degrees, this hole in the camshaft gear should exactly align with the pin hole of the camshaft bracket number 1.

Nov 24, 2013 | Toyota Corolla Cars & Trucks

1 Answer

Why are there 4 valve timing marks on a Mazda FE sohc engine


Some marks may not be timing marks. Don't rely on the marks. Find out how to time it by looking at the way the pistons line up and consult an expert if needed.

Jul 10, 2013 | Cars & Trucks

1 Answer

1996 toyota camry 2.2 5s- too manny timing marks crank shaft,cam shaft and cam shaft gears


Hi there:I dont have this diagram for 2S-ELC, 3S-FE and 5S-FE Engines, but pay attention at this...
To install:
  1. Align the cutouts of the oil pump pulley and shaft, and slide the pulley on. Retain the pulley while tightening the nut to 21 ft. lbs. (28 Nm).
  2. Align the crankshaft timing pulley set key with the key groove of the crankshaft pulley, then slide the pulley on.
  3. Install the No. 2 idler pulley with the bolt and tighten to 31 ft. lbs. (42 Nm). Be sure the pulley moves smoothly.

Remove any oil or water on the idler pulley and keep it clean.

  1. Temporarily install the No. 1 idler pulley with the retaining bolt. Hint: use a 1.65 inch (42mm) bolt in length. Do not tighten the bolt yet. Install the tension spring. Pry the pulley toward the left as far as it will go, then tighten the bolt.
  2. Turn the crankshaft until the key groove in the crankshaft timing pulley is facing upward. Install the timing belt on the crankshaft timing, oil pump, No. 2 idler and water pump pulleys.

If the old timing belt is being reinstalled, make sure the directional arrow is facing in the original direction and that the belt and crankshaft gear matchmarks are properly aligned.

  1. Install the lower (No. 1) timing belt cover and new gasket with the four bolts.
  2. Align the crankshaft pulley set key with the pulley key groove. Install the pulley. Tighten the pulley bolt to 80 ft. lbs. (108 Nm).
  3. On 2S-ELC engines, turn the crankshaft pulley and align the 0 mark on the lower (No. 1) timing belt cover.
  4. Align the camshaft knock pin with the matchmarks on the oil seal retainer.
  5. On 2S-ELC/USA engines, align the knock pin with the pin hole on the timing pulley E mark side. On 2S-ELC/Canadian engines, align the knock pin with the pin hole on the timing pulley. On 3S-FE and 5S-FE engines, align the knock pin with the groove of the pulley, and slide the pulley onto the camshaft with the plate washer and set bolt.

On 2S-ELC engines, make sure that the Matchmark on the oil seal retainer and center hole of the small hole on the camshaft timing pulley are aligned.

  1. Using the removal tool to hold the pulley stationary, install and tighten the pulley set bolt to 40 ft. lbs. (54 Nm) on the 2S-ELC and the 3S-FE. On the 5S-FE, tighten the set bolt to 27 ft. lbs. (37 Nm).
  2. On 3S-FE and 5S-FE engines, turn the crankshaft pulley and align the 0 mark on the lower (No. 1) timing belt cover.
  3. Install the timing belt and check the valve timing as follows:
    1. Align the matchmarks that you made previously, and install the timing belt onto the camshaft pulley.
    2. Loosen the No. 1 idler pulley set bolt 1 / 2 turn.
    3. Turn the crankshaft pulley two complete revolutions TDC to TDC. ALWAYS turn the crankshaft CLOCKWISE. Check that the pulleys are still in alignment with the timing marks.
    4. Tighten the No. 1 idler pulley set bolt to 31 ft. lbs. (42 Nm).
    5. Make sure there is belt tension between the crankshaft and camshaft timing pulleys.

  4. Install the upper (No. 2) timing cover with a new gasket(s). On the 5S-FE, align the two clamps for the engine wiring harness with the cover mounting bolts.
  5. Install the spark plugs.
  6. Install the right mounting insulator with bracket. Tighten the bracket bolts to 38 ft. lbs. (52 Nm), insulator nuts to 38 ft. lbs. (52 Nm) and thru-bolt to 52 ft. lbs. (71 Nm). On the 5S-FE, install the No. 2 engine mount bracket and tighten to 38 ft. lbs. (52 Nm); install the control rod and tighten the bolts to 47 ft. lbs. (64 Nm).
  7. Lower the engine.
  8. On 3S-FE and 5S-FE engines, install the alternator and alternator bracket. On 2S-ELC engines, install the power steering reservoir tank.
  9. Install the drive belt and adjust the tension.
  10. Install the cruise control actuator with bracket.
  11. Install the fender apron seal and right engine under cover.
  12. Install the right front wheel.


Hope this helps.

Jun 12, 2012 | Toyota Cars & Trucks

1 Answer

I need timing marks on 2.2 toyota camry 2000


1. Remove the fan and generator V belt:
tdisline_542.jpg

tdisline_543.jpg 2. TIMING CHAIN (2az-FE Engine):
Before servicing the vehicle, refer to the Precautions Section.
Drain the engine oil.
Remove or disconnect the following:
Negative battery cable
Hood Right-side front wheel Engine under covers Right-side fender apron seal Front exhaust pipe Engine moving control rod and bracket Right-side engine mounting stay and bracket Accessory drive belt Engine appearance cover Engine wire Alternator Power steering pump, leave the hoses connected Ignition coils Ventilation hoses Cylinder head cover Turn the crankshaft pulley to set the No. 1 cylinder to TDC compression. Align the groove on the pulley with the timing mark -0- on the front cover. Remove the crankshaft pulley as follows:
1. TMC made: Use Special Tool 09213-54015 to hold the pulley to loosen the bolt. Use Special Tool 09950-50013 to remove the bolt and pulley.

2. TMMK made: Use Special Tool 09960-10010 to hold the pulley to remove the bolt. Use Special Tool 09950-40011 to remove the crankshaft pulley
tdisline_544.jpg Fig. Removing the crankshaft pulley-TMC-2.4L (2AZ-FE) engine
tdisline_545.jpg

Fig. Removing the crankshaft pulley-TMMK-2.4L (2AZ-FE) engine

Remove or disconnect the following:
Crankshaft position sensor Lower oil pan No. 1 chain tensioner Accessory drive belt tensioner

  • Support the engine with a suitable engine lifting device.
  • Remove or disconnect the following:
    Engine mounting insulators Right-side engine mounting bracket Stud bolt for the accessory drive belt tensioner from the block Front cover mounting bolts and nuts Front cover Crankshaft position sensor plate Timing chain tensioner slipper Timing chain vibration damper Timing chain Crankshaft timing sprocket
  • Turn the crankshaft counterclockwise by 90°, and align an adjusting hole of the oil pump driven sprocket with the groove of the oil pump.
    tdisline_546.jpg
  • Fig. Align the adjusting hole of the oil pump drive sprocket with the oil pump groove-2.4L (2AZ-FE) engine
    tdisline_551.jpg

    Fig. Insert a bar to lock the sprocket in position-2.4L (2AZ-FE) engine
    Put a bar in the adjusting hole of the oil pump driven sprocket to temporarily lock the sprocket in position. Remove the nut.

    Remove the bolt, chain tensioner and spring.

    Remove the chain tensioner, oil pump sprocket and No. 2 timing chain.

    To install:
    Set the crankshaft key into the left horizontal position. Turn the cutout of the drive shaft to the top

    tdisline_552.jpg

  • Fig. Align the crankshaft key and drive shaft cutout as shown for installation-2.4L (2AZ-FE) engine
    Align the yellow colored links with the timing marks of the sprocket as shown in the illustration.

  • Insert the sprockets with chain to the crankshaft and oil pump shaft.
  • Temporarily tighten the oil pump driven sprocket with the nut.
  • Insert the damper spring into the adjusting hole, and install the chain tensioner plate with the nut. Tighten to 9 ft. lbs. (12 Nm).
  • Align the adjusting hole of the oil pump driven sprocket with the groove of the oil pump.
  • Put a bar in the adjusting hole of the oil pump driven sprocket to temporarily lock the sprocket in position. Tighten the nut to 22 ft. lbs. (30 Nm).
  • Rotate the crankshaft counterclockwise by 90°, and align the crankshaft key to the top.
  • Install the timing chain vibration damper. Tighten to 80 inch lbs. (9 Nm).
  • Align the timing marks of the camshaft timing sprockets and bearing caps.
  • Using the crankshaft pulley bolt, turn the crankshaft and set the set key on the crankshaft upward.
  • Align the gold or orange colored link with the timing mark of the crankshaft timing sprocket.
  • Using Special Tool 09309-37010, tap in the sprocket.
  • Align the gold or yellow colored links with the timing marks of the camshaft timing gear and camshaft timing sprocket. Install the chain.
  • tdisline_553.jpg Fig. Align the marks of the sprockets and bearing caps to set the No. 1 cylinder at TDC-2.4L (2AZ-FE) engine
    tdisline_554.jpg Fig. Set the crankshaft set key facing upward-2.4L (2AZ-FE) engine
    tdisline_555.jpg Fig. Align the marked link of the timing chain with crankshaft sprocket timing mark-2.4L (2AZ-FE) engine
    tdisline_556.jpg Fig. Tap the crankshaft sprocket in with Special Tool 09309-37010-2.4L (2AZ-FE) engine
    tdisline_557.jpg Fig. Align the marked links of the timing chain with the camshaft sprockets during installation-2.4L (2AZ-FE) engine

    May 21, 2011 | Toyota Camry Cars & Trucks

    1 Answer

    Gearbox chatter on tick over do they suffer from dualmass problems also is there a quick way to change the cambelt


    Dual Mass Flywheel, and will also need new clutch Remove the engine coverUsing a [16 mm], rotate the tensioner arm clockwise (about 14° )and remove the belt from the pulley.
    Remove the power steering pump pulley, idler pulley, tensioner pulley and crankshaft pulley.
    Remove the upper and lower timing belt covers.

    Remove the auto tensioner.
    NOTE
    Rotate the crankshaft clockwise and align the timing mark to set the No.1 cylinder's piston to TDC (compression stroke).
    At this time, the timing marks of the camshaft sprocket and cylinder head cover should coincide with each other.




    Unbolt the tensioner to remove the timing belt.
    NOTE
    If you plan to use the timing belt again, mark the rotation direction on the belt so you reinstall it correctly.

    SERVICE MANUAL
    Applies to: Santa Fe 2004
    GROUP
    Engine Mechanical System Timing System



    INSTALLATION
    Install the idler pulley to water pump boss.
    NOTE
    Insert and install the idler pulley to the roll pin that is pressed in the water pump boss.


    Install the tensioner arm and plain washer to the cylinder block.
    Install the tensioner pulley to the tensioner arm.
    Install the camshaft sprockets and align the timing marks.

    NOTE
    When installing the camshaft sprockets, fasten them tightly while holding the hexagonal part of the camshaft.
    Before installing the timing belt, if the timing marks of the cam sprocket and the cylinder head cover do not coincide, do not rotate the cam sprocket more than 3 teeth in either direction.
    Rotating the sprocket more than 3 teeth may allow the valve and piston to touch each other.
    If the cam sprocket is rotated more than 3 teeth unavoidably, rotate the crankshaft counter - clock wise a bit before rotating the cam sprocket.
    Install the auto tensioner to the front case.
    NOTE
    At this time auto tensioner's set pin should be compressed and secured with set pin.




    Align the timing marks of each sprocket and install the timing belt in the following order. Crankshaft sprocket--> Idler pulley--> camshaft sprocket (LH side)--> Water pump pulley--> camshaft sprocket (RH side)--> Tensioner pulley.
    NOTE
    In this step, No. 1 cylinder is in the TDC (Compression stroke).
    Be very careful if you use your fingers.



    Pull out the set pin of the auto tensioner.



    Install the upper and lower timing belt covers.
    Install the power steering pump pulley, idler pulley, tensioner pulley and crankshaft pulley.
    Using the wrench [16mm], rotate the tensioner arm clockwise (about 14°) and install the belt to the pulley.
    Install the engine cover.
    How to adjust the tension of the timing belt
    Rotate the crankshaft 2 turns clockwise and measure the projected length of the auto tensioner at TDC (# 1 Compression stroke) after 5 minutes.
    The projected length should be 6-8 mm.
    Verify that the timing marks of each sprocket are in their specified position.
    NOTE
    If the timing marks are not in their specified position, repeat from 6 above.

    Dec 28, 2010 | 2004 Hyundai Santa Fe

    1 Answer

    How do you set the timming on a 2.3 when your putting the new timming belt on


    The IGNITION timing on your Ranger is computer-controlled and is not adjustable.


    Should the camshaft drive belt/timing belt jump timing by a tooth or two, the engine could still run; but very poorly. To visually check for correct timing of the crankshaft, auxiliary shaft, and the camshaft follow this procedure:
    There is an access plug provided in the cam drive belt cover so that the camshaft timing cam be checked without moving the drive belt cover.
    1. Remove the access plug.
    2. Turn the crankshaft until the timing marks on the crankshaft indicate TDC.
    3. Make sure that the timing mark on the camshaft drive sprocket is aligned with the pointer on the inner belt cover.

    Never turn the crankshaft of any of the overhead cam engines in the opposite direction of normal rotation. Backward rotation of the crankshaft may cause the timing belt to slip and alter the timing.
    REMOVAL & INSTALLATION

    See Figures 1, 2 and 3


    0996b43f80211842.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Fig. 1: Timing belt cover on the 2.3L and 2.5L engine


    0996b43f80211843.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Fig. 2: Timing belt assembly on the 2.3L and 2.5L engine


    0996b43f80211844.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Fig. 3: Releasing the timing belt tensioner using a special tool

    1. Rotate the engine so that No. 1 cylinder is at TDC on the compression stroke. Check that the timing marks are aligned on the camshaft and crankshaft pulleys. An access plug is provided in the cam belt cover so that the camshaft timing can be checked without removal of the cover or any other parts. Set the crankshaft to TDC by aligning the timing mark on the crank pulley with the TDC mark on the belt cover. Look through the access hole in the belt cover to make sure that the timing mark on the cam drive sprocket is lined up with the pointer on the inner belt cover.

    Always turn the engine in the normal direction of rotation. Backward rotation may cause the timing belt to jump time, due to the arrangement of the belt tensioner.
    1. Drain cooling system. Remove the upper radiator hose as necessary. Remove the fan blade and water pump pulley bolts.


    Dec 11, 2010 | 1995 Ford Ranger Supercab

    1 Answer

    Procedure in changing timing belt


    Timing Belt and Sprockets REMOVAL & INSTALLATION 2S-ELC, 3S-FE and 5S-FE Engines
    1. Remove the timing belt covers as previously detailed.
    2. Raise the engine just enough to remove the weight from the engine mount on the right side.
    3. Remove the thru-bolt, two nuts, and right hand mounting insulator.
    4. Remove the retaining bolts and remove the right hand mounting bracket (from the side the alternator was removed from).
    5. Remove the timing belt and timing belt guide. If the timing belt is to be reused, draw a directional arrow on the timing belt in the direction of engine rotation (clockwise) and place matchmarks on the timing belt and crankshaft gear.
    6. Remove the bolt retaining the No. 1 idler pulley and tension spring.
    7. Remove the No. 2 idler pulley.
    8. Remove the crankshaft timing gear , if it can not be removed by hand, use two flat bladed tools to pry it off. Make sure to position shop rags to prevent damages to the components.
    9. Remove the nut retaining the oil pump pulley. To install:
    10. Align the cutouts of the oil pump pulley and shaft, and slide the pulley on. Retain the pulley while tightening the nut to 21 ft. lbs. (28 Nm).
    11. Align the crankshaft timing pulley set key with the key groove of the crankshaft pulley, then slide the pulley on.
    12. Install the No. 2 idler pulley with the bolt and tighten to 31 ft. lbs. (42 Nm). Be sure the pulley moves smoothly. NOTE: Remove any oil or water on the idler pulley and keep it clean.
    13. Temporarily install the No. 1 idler pulley with the retaining bolt. Hint: use a 1.65 inch (42mm) bolt in length. Do not tighten the bolt yet. Install the tension spring. Pry the pulley toward the left as far as it will go, then tighten the bolt.
    14. Turn the crankshaft until the key groove in the crankshaft timing pulley is facing upward. Install the timing belt on the crankshaft timing, oil pump, No. 2 idler and water pump pulleys. NOTE: If the old timing belt is being reinstalled, make sure the directional arrow is facing in the original direction and that the belt and crankshaft gear matchmarks are properly aligned.
    15. Install the lower (No. 1) timing belt cover and new gasket with the four bolts.
    16. Align the crankshaft pulley set key with the pulley key groove. Install the pulley. Tighten the pulley bolt to 80 ft. lbs. (108 Nm).
    17. On 2S-ELC engines, turn the crankshaft pulley and align the 0 mark on the lower (No. 1) timing belt cover.
    18. Align the camshaft knock pin with the matchmarks on the oil seal retainer.
    19. On 2S-ELC/USA engines, align the knock pin with the pin hole on the timing pulley E mark side. On 2S-ELC/Canadian engines, align the knock pin with the pin hole on the timing pulley. On 3S-FE and 5S-FE engines, align the knock pin with the groove of the pulley, and slide the pulley onto the camshaft with the plate washer and set bolt. NOTE: On 2S-ELC engines, make sure that the Matchmark on the oil seal retainer and center hole of the small hole on the camshaft timing pulley are aligned.
    20. Using the removal tool to hold the pulley stationary, install and tighten the pulley set bolt to 40 ft. lbs. (54 Nm) on the 2S-ELC and the 3S-FE. On the 5S-FE, tighten the set bolt to 27 ft. lbs. (37 Nm).
    21. On 3S-FE and 5S-FE engines, turn the crankshaft pulley and align the 0 mark on the lower (No. 1) timing belt cover.
    22. Install the timing belt and check the valve timing as follows:
      1. Align the matchmarks that you made previously, and install the timing belt onto the camshaft pulley.
      2. Loosen the No. 1 idler pulley set bolt 1⁄2 turn.
      3. Turn the crankshaft pulley two complete revolutions TDC to TDC. ALWAYS turn the crankshaft CLOCKWISE. Check that the pulleys are still in alignment with the timing marks.
      4. Tighten the No. 1 idler pulley set bolt to 31 ft. lbs. (42 Nm).
      5. Make sure there is belt tension between the crankshaft and camshaft timing pulleys.
    23. Install the upper (No. 2) timing cover with a new gasket(s). On the 5S-FE, align the two clamps for the engine wiring harness with the cover mounting bolts.
    24. Install the spark plugs.
    25. The remainder of installation is the reverse of removal. Tighten each component to specifications.

    Aug 04, 2010 | 1996 Toyota Camry

    1 Answer

    I have a 1994 eagle talon i replaced the water pump and put on a new timing belt and i can not get the timing right i have tried everything i know what could i be doing wrong? I have made sure the number...


    I'm looking at the manual (68030 Haynes) and it shows that if you have the DOHC you make the 2 marks onthe camshafts meet in the center.

    That would be at the 3 o'clock position for the left one, and 9 o'clock position for the right one. the crank sprocket and oil pump sprocket align exactly with the timing marks.

    NOW, on the SOHC single cam pulley, crankshaft and oil pump pulley all are to be aligned with their index marks, centered, and the balance shaft is to be with the weighted side down to prevent vibration.

    I've done the SOHC and the marks are fairly centered when instlalling. Once you've got the belt on in either engine, you should rotate the engine in the normal direction for 2 full revolutions and recheck the timing marks at all positions, readjust, rotate and recheck until set on the marks.

    Good luck,

    Feb 21, 2010 | 1994 Eagle Talon

    1 Answer

    Setting crankshaft and camshaft timing


    with crank pulley white mark on 0 remove both cam pulley covers and verify yellow painted notches are exactly on the T mark cast in the fwd cam bearing housings..IF u find that it ISNT 'in time' then remove tensioner located near crank pulley and very carefully manipulate the L and R cam sprokets to allow belt to removed from cam sprockets only... DoNOT rotate engine without T belt installed .Do NOT turn engine backwards.. ever.. be advised that should the cam timing be off by more than 3 teeth either way serious engine damage will result ..this series of engines utilizes variable intake camshaft adjustment .. This job is not for the american small block specialist of yesteryear.. even an experienced asian tech is gonna have a difficult time with this lexus .. its not quite the same engine the Tundra uses...Lexus only mods befuddle reg toyota techs

    Aug 27, 2008 | 1996 Lexus LS 400

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    2,181 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Mazda Experts

    yadayada
    yadayada

    Level 3 Expert

    76132 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8273 Answers

    Are you a Mazda Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...