Question about 1999 Hyundai Sonata

2 Answers

Engine stops driving along freeway, can be restarted

Petrol was near E(mpty) so filled up on Wednesday. Drove 85 kms out of city and engine stopped dead. Restarted and drove 200 metres and stopped again. Sat in car for 5 mins and engine started and drove for another 10 mins and stopped dead. Turned around and headed back to Sydney and car didn;pt stop again. Fells like the engine is a little retarded but stops and starts everytime since. Any clues? I and my dad suspect dirty fuel or water in fuel tank/line. Hyundai service people told us quote "teh lines are full of oil and the oil is getting onto your spark plugs, we will need to replace the rocker cover gasket" WHAT!???!???!????

Posted by on

  • 1 more comment 
  • kylej_90 May 25, 2011

    How to bypass the immobilizer in 99 sonata

  • kylej_90 May 25, 2011

    How to bypass the immobilizer in 99 sonata

  • kylej_90 May 25, 2011

    How to bypass the immobilizer in 99 sonata

×

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Something else to watch for, not saying this is your problem, but our hy. Excel used to stop on the road for no reason......turned out to be the contacts in the ignition switch. It's a very cheaply made plasticy (is that a word?) switch and the contacts were loose and sloppy. Pulled switch apart and overhauled it and Bob's ya uncle

Posted on Apr 14, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Hyundai Master
  • 22,156 Answers

I think you have mis understood the garage ,oil on leads will not help the car run right either as it will short them out .But you have to watch some shady pratices from dealers who like to milk the golden cow,by saying that before they can rectify one thing they have to rebuild the car .But yes a leaky rocker cover gasket could stop the car if the plug leads were wet enough with oil.

Posted on Apr 14, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I ask a question on what is the drive cycle to reset obd for toyota2005 rav4


Step One: How to Prepare Your Vehicle
  • Have the fuel tank between 30 and 70 percent full. Some systems, especially the EVAP system, need to have a specific level of fuel in order for the tests to be trusted. If the fuel tank is near empty or completely full, many of the basic tests will not run at all.
  • The vehicle must also have a good alternator and a strong battery. If you have to occasionally jump-start your vehicle, all of the memory from the powertrain control module (PCM) is erased, which includes the data that accurately tracks the results from various stages of the Drive Cycle. Also, if the battery is weak or undercharged, some of the most important tests will never run.
  • The vehicle must sit overnight, or for at least eight hours, in an environment that is less than 90° F. The engine temperature needs to match the air temperature in order to establish an accurate baseline for the testing. If the outside temperature is over 90° F, the fuel is too volatile and the EVAP system won't even try to run its tests, though some of the other emissions systems may run their tests.
  • The keys must be out of the ignition and all of the doors must be closed while the vehicle sits over night because many of the onboard computers "boot up" when the keys are in the ignition. Also, many of the onboard computers still run until all of the doors are closed after the vehicle is shut off and the keys are removed.
Step Two: The Cold Start
  • Start the vehicle and let it idle for two to three minutes in Park or Neutral. While it is idling, turn on the head lights, heater/defroster, and rear defroster for a three to five minute warm-up phase. Let the idle speed settle down to near the normal speed.
  • Next, put the vehicle in gear and drive through city streets at about 25 mph. Go up to about 35 to 40 mph a few times before slowing down to stop. Don't roll through the stop; be sure the car is really stopped, just like you learned in driving school. Accelerate from each stop in a normal fashion-not overly conservative, but not like you are competing in a drag race either.
Step Three: A Short Freeway Trip
  • After the vehicle has been cold started and driven for a few miles on city streets, the next step is to take it on a short freeway trip.
  • Enter the freeway on-ramp and allow enough room with respect to other vehicles so that you can do a 1/2 to 3/4 throttle acceleration up to freeway speed.
  • When you have accelerated up to around 60 mph and have safely merged into the flow of traffic, stay in the slow lane and maintain a steady speed of 55 to 60 mph for a minimum of five miles. Please use the cruise control to help you maintain speed.
  • Find a nice, long off ramp to exit from the freeway. As you exit, take your foot off of the accelerator and let the vehicle coast down until it stops under its own power as you complete your exit from the freeway. Do not use the foot brake and do not shift gears until the very end of this "coast down" phase.
  • Step Four: More City Driving
    • After you have completed the freeway trip, drive through the city streets for a repeat of the second part of Step Two.
    • Go up to about 35 to 40 mph a few times and then maintain a city speed of 25 mph before slowing down to stop. Again, don't roll through the stop and make sure to accelerate normally.
    • Pull in to a parking place and let the engine idle for one to two minutes and then shut it off.
    Step Five: Have your Readiness Monitors Checked and Verified
    • Drive your vehicle to your regular shop and have them re-check your readiness monitors, present codes, and pending codes. They should do this as a courtesy and for free.
    • If all of your monitors are "ready" and there are no present or pending codes, then your vehicle has been properly repaired and is ready for an emissions inspection and for normal driving.

Feb 21, 2017 | Cars & Trucks

1 Answer

How to do the drive cycle of a 1996 Nissan pathfinder


How to Perform a Basic Drive Cycle


Step One: How to Prepare Your Vehicle

  • Have the fuel tank between 30 and 70 percent full. Some systems, especially the EVAP system, need to have a specific level of fuel in order for the tests to be trusted. If the fuel tank is near empty or completely full, many of the basic tests will not run at all.
  • The vehicle must also have a good alternator and a strong battery. If you have to occasionally jump-start your vehicle, all of the memory from the powertrain control module (PCM) is erased, which includes the data that accurately tracks the results from various stages of the Drive Cycle. Also, if the battery is weak or undercharged, some of the most important tests will never run.
  • The vehicle must sit overnight, or for at least eight hours, in an environment that is less than 90° F. The engine temperature needs to match the air temperature in order to establish an accurate baseline for the testing. If the outside temperature is over 90° F, the fuel is too volatile and the EVAP system won't even try to run its tests, though some of the other emissions systems may run their tests.
  • The keys must be out of the ignition and all of the doors must be closed while the vehicle sits over night because many of the onboard computers "boot up" when the keys are in the ignition. Also, many of the onboard computers still run until all of the doors are closed after the vehicle is shut off and the keys are removed.
Step Two: The Cold Start
  • Start the vehicle and let it idle for two to three minutes in Park or Neutral. While it is idling, turn on the head lights, heater/defroster, and rear defroster for a three to five minute warm-up phase. Let the idle speed settle down to near the normal speed.
  • Next, put the vehicle in gear and drive through city streets at about 25 mph. Go up to about 35 to 40 mph a few times before slowing down to stop. Don't roll through the stop; be sure the car is really stopped, just like you learned in driving school. Accelerate from each stop in a normal fashion-not overly conservative, but not like you are competing in a drag race either.
Step Three: A Short Freeway Trip
  • After the vehicle has been cold started and driven for a few miles on city streets, the next step is to take it on a short freeway trip.
  • Enter the freeway on-ramp and allow enough room with respect to other vehicles so that you can do a 1/2 to 3/4 throttle acceleration up to freeway speed.
  • When you have accelerated up to around 60 mph and have safely merged into the flow of traffic, stay in the slow lane and maintain a steady speed of 55 to 60 mph for a minimum of five miles. Please use the cruise control to help you maintain speed.
  • Find a nice, long off ramp to exit from the freeway. As you exit, take your foot off of the accelerator and let the vehicle coast down until it stops under its own power as you complete your exit from the freeway. Do not use the foot brake and do not shift gears until the very end of this "coast down" phase.
Step Four: More City Driving
  • After you have completed the freeway trip, drive through the city streets for a repeat of the second part of Step Two.
  • Go up to about 35 to 40 mph a few times and then maintain a city speed of 25 mph before slowing down to stop. Again, don't roll through the stop and make sure to accelerate normally.
  • Pull in to a parking place and let the engine idle for one to two minutes and then shut it off.
Step Five: Wave your Readiness Monitors Checked and Verified
  • Drive your vehicle to your regular shop and have them re-check your readiness monitors, present codes, and pending codes. They should do this as a courtesy and for free.
  • If all of your monitors are "ready" and there are no present or pending codes, then your vehicle has been properly repaired and is ready for an emissions inspection and for normal driving.
  • If your monitors are not ready, please click here for more information.

May 26, 2016 | Nissan Cars & Trucks

1 Answer

How to do the drive cycle on a 1996 nissan pathfinder


How to Perform a Basic Drive Cycle


Step One: How to Prepare Your Vehicle

  • Have the fuel tank between 30 and 70 percent full. Some systems, especially the EVAP system, need to have a specific level of fuel in order for the tests to be trusted. If the fuel tank is near empty or completely full, many of the basic tests will not run at all.
  • The vehicle must also have a good alternator and a strong battery. If you have to occasionally jump-start your vehicle, all of the memory from the powertrain control module (PCM) is erased, which includes the data that accurately tracks the results from various stages of the Drive Cycle. Also, if the battery is weak or undercharged, some of the most important tests will never run.
  • The vehicle must sit overnight, or for at least eight hours, in an environment that is less than 90° F. The engine temperature needs to match the air temperature in order to establish an accurate baseline for the testing. If the outside temperature is over 90° F, the fuel is too volatile and the EVAP system won't even try to run its tests, though some of the other emissions systems may run their tests.
  • The keys must be out of the ignition and all of the doors must be closed while the vehicle sits over night because many of the onboard computers "boot up" when the keys are in the ignition. Also, many of the onboard computers still run until all of the doors are closed after the vehicle is shut off and the keys are removed.
Step Two: The Cold Start
  • Start the vehicle and let it idle for two to three minutes in Park or Neutral. While it is idling, turn on the head lights, heater/defroster, and rear defroster for a three to five minute warm-up phase. Let the idle speed settle down to near the normal speed.
  • Next, put the vehicle in gear and drive through city streets at about 25 mph. Go up to about 35 to 40 mph a few times before slowing down to stop. Don't roll through the stop; be sure the car is really stopped, just like you learned in driving school. Accelerate from each stop in a normal fashion-not overly conservative, but not like you are competing in a drag race either.
Step Three: A Short Freeway Trip
  • After the vehicle has been cold started and driven for a few miles on city streets, the next step is to take it on a short freeway trip.
  • Enter the freeway on-ramp and allow enough room with respect to other vehicles so that you can do a 1/2 to 3/4 throttle acceleration up to freeway speed.
  • When you have accelerated up to around 60 mph and have safely merged into the flow of traffic, stay in the slow lane and maintain a steady speed of 55 to 60 mph for a minimum of five miles. Please use the cruise control to help you maintain speed.
  • Find a nice, long off ramp to exit from the freeway. As you exit, take your foot off of the accelerator and let the vehicle coast down until it stops under its own power as you complete your exit from the freeway. Do not use the foot brake and do not shift gears until the very end of this "coast down" phase.
Step Four: More City Driving
  • After you have completed the freeway trip, drive through the city streets for a repeat of the second part of Step Two.
  • Go up to about 35 to 40 mph a few times and then maintain a city speed of 25 mph before slowing down to stop. Again, don't roll through the stop and make sure to accelerate normally.
  • Pull in to a parking place and let the engine idle for one to two minutes and then shut it off.
Step Five: Wave your Readiness Monitors Checked and Verified
  • Drive your vehicle to your regular shop and have them re-check your readiness monitors, present codes, and pending codes. They should do this as a courtesy and for free.
  • If all of your monitors are "ready" and there are no present or pending codes, then your vehicle has been properly repaired and is ready for an emissions inspection and for normal driving.
  • If your monitors are not ready, please click here for more information.

May 26, 2016 | Nissan Cars & Trucks

1 Answer

99 Intrepid 3.2 engine stalls no check engine lite. Does not happen often but usually within first 15 minutes or so after first start of the day. About 10 times in last 5 months. Sometimes immediate...


Does this trips the check engine lamp to store a code? If possible you should take the Vehicle near a local auto parts store to have the code retrived. How many miles are on your vehilce?

May 09, 2011 | Dodge Intrepid Cars & Trucks

2 Answers

While driving in 100+ degree heat, my van died.


SOUND LIKE COOLANT FAN NOT COMING ON.WHEN YOU ARE IN CITY.YOUR ENGINE RADIATOR NOT GETTING MUCH AIR FLOW IN THE CITY.BECAUSE YOU STOP AND GO ALOT.DUE TO A LOT OF STOP LIGHTS.CHECK COOLANT FAN RELAY AND FUSE.IF BOTH GOOD.COOLANT TEMPERATURE SENSOR SENSOR.IF ALL IS GOOD HOT WIRE COOLANT FAN TO SEE IF IT RUNS.IF NO FAN MOTOR BAD.IF YES FAN MOTOR RUNS WIRE CONNECTOR IS OPEN OR DAMAGED.

Aug 02, 2010 | 1993 Dodge Caravan

2 Answers

I have a 2008 pt cruiser. The engine light is on


My PT cruiser is a couple of years older, but I had the same problem. Drove fine, but start-up was erratic for several weeks. By the time  AAA arrived, it usually was working fine. But when it suddenly  started "struggling for power on the freeway and further along on the same trip, lurching (on a city avenue) I drove straight to my mechanic. It WAS the same sensor . . . and car has been driving perfectly ever since he changed it.

Mar 24, 2010 | 2005 Chrysler PT Cruiser

1 Answer

1999 chevy tahoe flashing check engine light and noise


DO NOT DRIVE THE VEHICLE A FLASHING CHECK ENGINE LIGHT COULD IS ASUALY A SERIOUS SAFETY HAZARD TAKE IT TO A SHOP IMMEDIATLY

Sep 23, 2009 | 1997 Chevrolet Tahoe

4 Answers

Montero sport stalls at stops after battery change.


remove the cable again. Then when you start it allow it to idle for 20 mins in park.

Dec 27, 2008 | 1999 Mitsubishi Montero Sport

1 Answer

OBII readness "not ready"


what kind of car is it
some cars montier take
a while to get ready
try driving on the freeway, if it's doesn't get ready
then try driving in the city, some montier get ready
if the car is driven in the city stop and go

Sep 12, 2008 | 1995 Hyundai Sonata

Not finding what you are looking for?
1999 Hyundai Sonata Logo

144 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...