Question about 1978 Chevrolet C1500

2 Answers

I have a 1980 c-10 chevy pick-up truck, my signal and brake lights dont work.

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Replace the turn signal switch in the colume

Posted on Apr 14, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

It's a fuse. had the same on my 80 c-10 p.u.. the fuse kept blowin, went 5amps higher on the fuse, never happened again. don't go crazy on fuse size, you don't need a fire. but, as things get older any thing goes for reliability and safety.

Posted on Nov 21, 2010

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 366 Answers

SOURCE: 1982 chevy tail lights not working

if u have trailer plug check there for broken wire at plug elect.connection,if not,usually on trucks wire damage is at rear,if lights are working in frt.check elect.circuit from tail light housing going to frt

Posted on Apr 01, 2009

  • 14036 Answers

SOURCE: 1994 Chevy truck. Turn signals do not work.

CHECK FUSE.IF GOOD YOU HAVE A BAD GROUND OR FAULTY TURN SIGNAL FLASHER.FLASHERS LOCATED ON THE INTERIOR FUSE RELAY BOX.

Posted on Sep 22, 2009

  • 114 Answers

SOURCE: my 97 chevy blazer, the brake lights dont work but

More likely it is the hazard/turnsignal/highbeam/cruise control switch module. It costs about $275 for the module. However there is a repair kit for the likely culprit...the hazard button. Try jiggling it around a little, see if that helps. Spray a little WD-40 into it so it can jostle back into it's correct position. You could try a junkyard unit or Ebay. It's not too hard to change. The hard part is doing it without removing the steering wheel. It can be done. I've done it. But hopefully you can locate the repair kit which costs about 15 dollars. Good luck.

Posted on May 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Lower brake lights no longer work on my 2002 chevy tahoe but the 3rd brake light works fine. Checked fuse and bulbs and everything works fine. Just the 2 lower brake lights dont work.


Most of the time the problem is in the turn signal switch. The third brake light circuit bypasses the turn signals.
Someone would need to check brake light power in and out of the turn signal switch.

Feb 25, 2014 | GMC Cars & Trucks

1 Answer

1995 Chevy Caprice Wagon, right side signals and brake lights dont work


change the bulb if still out then check and test socket/ground wiring/wire harness for damage

Apr 28, 2017 | Cars & Trucks

1 Answer

Chevy S10. When my running lights are on everything works (except turn signals), front lights, tail lights brake lights. When I turn on my headlights turn signals still dont work everything comes on fine...


Check the grounds on your wiring.
If you have a trailer harness, make sure there are no shorts, or crusty connections

Good Luck chasing the gremlins

Oct 13, 2010 | 1996 Chevrolet K1500

1 Answer

Brakes Lights dont work on a 2006 Chevy Silverado


I've worked on these the first drove me crazy. its the turn signal switch every thing runs thru these. head lights, turn signal, brakes. except the third brake light. it runs directly from the brake switch. go figuare

Jun 22, 2010 | 2003 Chevrolet Tahoe

1 Answer

85 chevy 3/4 ton pick up .Rear brake light and turn singles dont work but parking lights work,fuse is ok brake switch is ok and front turn singles work as well as hazerds for the front only work and...


bad turn signal switch broken inside switch, need to remove steering wheel, remove clip, unplug connector under dash on column, undo the 3 screws hold switch in, install in reverse order.

Feb 11, 2010 | 1985 Chevrolet Chevy

1 Answer

1989 chevy 1/2 ton.brake lights or emergency flashers dont work.tail lights an blinkers work.


The Blinkers and the Brake Lights are the same bulb. So check the brake light switch. Flashers use a different flasher unit, than the turn signals

Dec 16, 2009 | 1989 Chevrolet K1500

1 Answer

My brake, hazard and turn lights dont work, i


well u have two seprate problems the hazards and turn signals have a flasher that needs replacing if the fuse is good on the fuse box marked signals .and there is a brake light switch under the dash board near the brake pedal it has two wires on it check the wires make sure they are connected if so replace the brake light switch

Nov 13, 2009 | 2002 Chevrolet Astro

1 Answer

I have a 1990 chevy s10,all my lights work except my brake lights


Do you have power with a test light in and out of the switch? Do the turn signals work? Will the brake lights work if you play with the turn signal handle?

May 06, 2009 | 1990 Chevrolet S 10 4WD

Not finding what you are looking for?
Cars & Trucks Logo

222 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...