Question about 2000 Mercury Villager

1 Answer

Handle broke off sliding door on drivers side 2000 mercury villag

How do I remove the inner door panel

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mercury Master
  • 4,369 Answers

Trim Panel —Sliding Door
Special Tool(s) handle broke off sliding door on drivers side 2000 - syv~us~en~file=st1181a.gif~gen~ref.gif Safety Belt Bolt Bit (Used for T-50 Head Bolt)
501-010 (T77L-2100-A) Removal

  1. Remove the sliding door trim panel finish panel.
94d5982.gif
  1. Remove the sliding door trim panel.

Posted on Apr 28, 2009

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 840 Answers

SOURCE: Broken handle on sliding door behind driver

First get vin call toyota parts dept/ get the part its really easy to put in look for screws in little pop ups take screws out then go from the bottom of the door and lift out then go side do the same thing then lift from bottom of door and upward then you will take of vapor or plastic sheet then you just replace the handle thats it then out it back together/ Please rate my response thank you very much

Posted on Feb 01, 2009

  • 26 Answers

SOURCE: Mazda 5 replacing external handle on sliding door

Your door should be held on with clips. Removing the panel is sometimes hard, just take a good WIDE flat head screwdriver, and whatever tool needed to remove the screws holding the panel on, and be careful. Check underneath the panel, by the inside handle, and the arm point for screws. Once removed, take your WIDE screw driver, and don't quite pry them off, more or less try to get it underneath and pull towards yourself. There is no real easy way, just try to be patient with it, and if you hit any binds, look for more screws, its just a matter of patience for sure.

Posted on Feb 14, 2009

  • 4369 Answers

SOURCE: Im looking for a sliding door handle for a 2000 nissan quest van.

ebay has them all the time also, go here for help on Quests http://autos.groups.yahoo.com/group/villagerquest/

Posted on Jun 08, 2009

  • 88 Answers

SOURCE: how to take off driver

Check door pull for a couple screws and check bottom of panel for more screws.Take a putty knife and pry out panel at lower outside corner very gently and look in to see if there are plastic pins if there are,put the putty knife next to pin and carefully pull out on panel.Do that around panel until it is loose then panel will come of.If there are no pin the panel is held on with what looks like a ell bracket,in that case with a little effort the panel should lift straight up, not straight out.It has been a couple year since I have done one of these but one of these ways should work just don't pry to hard on panel.Good luck

Posted on Dec 05, 2010

  • 827 Answers

SOURCE: how do i replace the door handle on the sliding

These are fun,. it would be in your best interest to contact your local library and see if they have the chilton and or haynes repair manual for your vehicle in stock,. if so, go take it out and read it as this can/ will be tricky at best otherwise.

If your local library doesn't have it, try your local auto parts store for around 25 bucks...

FYI: CALL FIRST & CONFIRM the book is there, otherwise it may have been hijacked from the library and not recorded...

Posted on Feb 13, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove inner handle on side sliding door?


Check for a horse shoe shaped clip on the shaft the handle is on and remove it with a small screw driver or the correct slide tool.

Mar 21, 2015 | Cars & Trucks

1 Answer

2000 Mercury Villager, third row bench stuck


you will have to take the mechanism apart and reseat the spring or replace the broken part.

May 29, 2014 | 2000 Mercury Villager

1 Answer

Driver side door rod to handle has come loose from the locking mechanism


There is a replacement clip available in most auto repair stores. HELP brand. Must remove the door panel (inside) and re-attach.

Feb 16, 2014 | 1995 Mercury Villager

1 Answer

How to replace an outside lock on sliding door of 2000 Mercury Villager


You have to take the Inside Panel off, disconnect the Rods and then remove the Clip.

Reassemble

TEST BEFORE YOU PUT the panel back on

Apr 12, 2013 | 2000 Mercury Villager

1 Answer

1997 mercury villager passenger side mirror replacement guide. how do i do it? is there an easy access panel or does the whole door panel need to be removed


door panel must come off.

go here for villager help

http://groups.yahoo.com/group/villagerquest/

Section 01-05: Trim, Interior 1997 Villager Workshop Manual
REMOVAL AND INSTALLATION Trim Panel(s), Door
Front
Removal
  1. Disconnect the battery ground cable (14301) if equipped with power locks or power windows.
  1. svv~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use care when removing the front door inside handle escutcheon (22620). Failure to do so can result in damage to the component.
    Carefully pry off the front door inside handle escutcheon by inserting a standard 1/4 inch screwdriver between the top rear portion of the front door inside handle escutcheon and the front door trim panel (23942).




  1. If equipped with manual windows, slip a clean shop rag between the window regulator handle (23342) and the front door trim panel.
  1. Pull the shop rag back and forth to release the window regulator handle clip.




  1. Remove the three cover caps and front door trim panel screws.
  1. Remove the one front door trim panel capped screw from the door pull handle.
  1. If equipped with power windows, remove the door pull handle. Disconnect the electrical connectors.
  1. Slide a flat-bladed tool behind each of the retainers and twist the tool to disengage the front door trim panel from the front door (20124).
  1. Remove the front door trim panel.
Installation
To install, reverse the removal procedure. Body Side
Removal
  1. Gently pry loose the body side door latch handle bezel and remove it.
  1. Slide a suitable tool behind each of the retainers and twist the tool to disengage the body side door trim panel from the body side door (24622).




Installation
To install, reverse the removal procedure. Door Electrical Connections
Removal and Installation
Refer to Section 01-11 for Power Window, Section 01-09 for Power Mirror, or Section 01-14B for Power Locks. Watershield
Removal
  1. Remove the Front Door Trim Panel . Refer to the removal procedure in this section.
  1. Remove the front door watershield by carefully detaching it from the adhesive.
Installation
  1. Install the front door watershield in the proper position and press firmly at the adhesive areas. If necessary, use additional adhesive to ensure an adequate seal.
  1. Install the Front Door Trim Panel . Refer to the installation procedure in this section.

May 22, 2010 | 1998 Mercury Villager

1 Answer

Fallen driver's side window


probably need a new window regulator. ebay. 93 to 98 should fit.

Section 01-05: Trim, Interior 1998 Villager Workshop Manual
REMOVAL AND INSTALLATION Trim Panel(s), Door Front
Removal
  1. Disconnect the battery ground cable (14301) if equipped with power locks or power windows.
  1. swv~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use care when removing the front door inside handle escutcheon (22620). Failure to do so can result in damage to the component.
    Carefully pry off the front door inside handle escutcheon by inserting a standard 1/4 inch screwdriver between the top rear portion of the front door inside handle escutcheon and the front door trim panel (23942) .




  1. If equipped with manual windows, slip a clean shop rag between the window regulator handle (23342) and the front door trim panel .
  1. Pull the shop rag back and forth to release the window regulator handle clip.




  1. Remove the three cover caps and front door trim panel screws.
  1. Remove the one front door trim panel capped screws from the door pull handle.
  1. If equipped with power windows, remove the door pull handle. Disconnect the electrical connectors.
  1. Slide a flat-bladed tool behind each of the retainers and twist the tool to disengage the front door trim panel from the front door (20124) .
  1. Remove the front door trim panel.
Installation
To install, reverse the removal procedure.
---------------------------------------------------------
Window Regulator, Power Front Door
Removal
  1. Disconnect the battery ground cable (14301) .
  1. Remove the front door window glass (21410) . Refer to the front door window glass removal procedure in this section.
  1. Remove the two front door brace bolts and the front door brace.


    415712f.gif

  1. Disconnect the front window regulator electric drive electrical connector.
  1. Remove the four front door window glass regulator track bolts.

    67b6136.gif


  1. Remove the three front window regulator electric drive bolts.
  1. Remove the front door window glass regulator track and the front window regulator electric drive (23394) as an assembly through the opening in the front door (20124) .
Installation
  1. Install the front door window glass regulator track and the front window regulator electric drive as an assembly through the opening in the front door .
  1. Install the three front window regulator electric drive bolts. Tighten the front window regulator electric drive bolts securely.
  1. Install the four front door window glass regulator track bolts. Tighten the front door window glass regulator track bolts securely.

Apr 29, 2009 | 1998 Mercury Villager

1 Answer

How do you remove the door panels on a 1995 mercury villager


http://autos.groups.yahoo.com/group/villagerquest/

you have to remove the cup behind the door handle. rmove screws aroun the door pull. get a screw driver and pry the trim panel away from the door carefully. There is a plastic christmas tree clip every 6 inches. when the bottom & sides are free, lift up the trim panel to get it out of the track at the base of the window.
--------------------------------------------------------------------------------------

Carefully pry off the front door inside handle escutcheon by inserting a standard 1/4 inch screwdriver between the top rear portion of the front door inside handle escutcheon and the front door trim panel (23942).

  1. Remove the three cover caps and front door trim panel screws.
  1. Remove the one front door trim panel capped screw from the door pull handle.
  1. If equipped with power windows, remove the door pull handle. Disconnect the electrical connections.
  1. Slide a flat-bladed tool behind each of the retainers and twist the tool to disengage the front door trim panel from the front door (20124).
  1. Remove the front door trim panel.

Jan 04, 2009 | 1995 Mercury Villager

1 Answer

Broken handle on sliding door behind driver


First get vin call toyota parts dept/ get the part its really easy to put in look for screws in little pop ups take screws out then go from the bottom of the door and lift out then go side do the same thing then lift from bottom of door and upward then you will take of vapor or plastic sheet then you just replace the handle thats it then out it back together/ Please rate my response thank you very much

Dec 28, 2008 | 1999 Toyota Sienna

Not finding what you are looking for?
2000 Mercury Villager Logo

Related Topics:

648 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

fordexpert

Level 3 Expert

5537 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...