Question about 1998 Plymouth Voyager

Open Question

How do I replace water outer tube O Ring on a 1998 Voyager 3.0

Replacing o ring for a inner and outer water pipe tube which is the the return coolant and heater core

Posted by on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 61 Answers

SOURCE: Heater hose coolant return tube

Yes you can remove the tube if its a V8. If its an inline 6 cylinder you have to remove the pump in order to repair the heater pipe.

Posted on Jan 29, 2009

Ad
motor1258
  • 6674 Answers

SOURCE: water outlet tube leaks

It inserts into back of water pump.Need I say more? Sorry.

Posted on Apr 12, 2009

  • 1 Answer

SOURCE: Water Pump leakes from steel tube.

when installing new o-ring on tube, lubricate o-ring and stick it in water pump. Then pull pressure back on tube and then tighten hold down clamp. problem solved

Posted on Oct 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I need to know what the pipe is called that the lower rad hose hooks up to on the 1998 plymouth grand voyager mini van 3.0L, 3 speed automatic ?


if you follow the pipe does it go towards the transmission ? if so it's for the trans cooler. If not it will be the escape hose incase of overheating/to much pressure in the coolant system , if you go to a parts retailer like autozone they will have the part named on their data system , its a bit difficult without seeing vehicle to name parts . although you have given a good description, the lower rad hose carries cooled coolant so i would think it's the trans cooler but check at autozone or similar

Jul 07, 2014 | 1998 Plymouth Grand Voyager

1 Answer

How to change water pump in 1987 chevy nova


1. Remove mounting bolts and remove upper timing cover and gasket. Drain coolant into clean bucket.
2. Loosen the 4 water pump pulley mounting bolts. Loosen alternator adjusting and mounting bolts and remove the belt.
3. Remove the water pump pulley bolts and the pulley.
4. Remove the water pump inlet mounting bolt from the side of the block and then remove the 2 nuts attaching the pipe to the water pump. Remove the pipe.
5. Remove the mounting bracket bolt and then remove the dipstick tube. Plug the hole with a rag. Remove the right hand under cover and the power steering adjusting bracket ( if it has power steering).
6.Remove the 3 bolts and remove the water pump. Keep coolant OFF the timing belt (plenty of rags to soak it up)., Remove the O ring from the block.
7. To install a new pump, start by replacing the O ring in the block. Then the reverse of these steps.
8. Water pump mounting bolts are torqued to 11 ft.lbs only. Also replace the O ring on the dipstick tube and coat it with oil before reinstalling.
9. Refill the cooling system and run the engine up to operating temperature, with the heater running. This will force the air out of the system. Once the air is out top up the rad and replace the rad cap.

Oct 24, 2013 | Chevrolet Cars & Trucks

1 Answer

Need to change water pump in 99 plymouth voyager 3.0 liter


  1. Disconnect the negative battery cable.
  2. Drain the cooling system.
  3. Remove the drive belts. Remove the timing belt covers and the timing belt.
  4. Remove the water pump mounting bolts.
  5. Separate the water pump from the water inlet pipe and remove the water pump.
  6. Inspect the water pump and replace as necessary.

To install:
  1. Clean all gasket and O-ring surfaces on the water pump and water pipe inlet tube.
  2. Wet a new O-ring with water and install it on the water inlet pipe.
  3. Install a new gasket on the water pump.

  1. Install the pump inlet opening over the water pipe and press until the pipe is completely inserted into the pump housing.
  2. Install the water pump-to-block mounting bolts and tighten to 20 ft. lbs.
  3. Install the timing belt and timing belt covers. Install and adjust the drive belts.
  4. Reconnect the negative battery cable. Fill the cooling system to the proper level with a 50 / 50 mixture of clean, ethylene glycol antifreeze and water.
  5. Run the engine and check for leaks. Top off the coolant level, if necessary.

Oct 16, 2013 | 1997 Plymouth Voyager

2 Answers

Need step by step to replace water pump on 1997 dodge caravan v-6 3,0 mits. motor...


Chrysler Caravan/Voyager/Town and Country 1996-1999 Water Pump - REMOVAL & INSTALLATION
3.0L Engine
See Figure

a812cd7.jpg

Fig. 3: Water pump mounting detail-3.0L engine
  1. Disconnect the negative battery cable.
  2. Drain the cooling system.
  3. Remove the drive belts. Remove the timing belt covers and the timing belt.
  4. Remove the water pump mounting bolts.
  5. Separate the water pump from the water inlet pipe and remove the water pump.
  6. Inspect the water pump and replace as necessary.

To install:
  1. Clean all gasket and O-ring surfaces on the water pump and water pipe inlet tube.
  2. Wet a new O-ring with water and install it on the water inlet pipe.
  3. Install a new gasket on the water pump.
  1. Install the pump inlet opening over the water pipe and press until the pipe is completely inserted into the pump housing.
  2. Install the water pump-to-block mounting bolts and tighten to 20 ft. lbs. (27 Nm).
  3. Install the timing belt and timing belt covers. Install and adjust the drive belts.
  4. Reconnect the negative battery cable. Fill the cooling system to the proper level with a 50 / 50 mixture of clean, ethylene glycol antifreeze and water.
  5. Run the engine and check for leaks. Top off the coolant level, if necessary.

Hope this help (remember comment and rated this).

Apr 13, 2010 | 1997 Dodge Grand Caravan

3 Answers

91 carolla water pump


No. You don't have to remove the timing belt to change the water pump. Check out the autozone.com website and register. It doesn't cost anything and you will have access to a repair manual for the vehicle. The steps for replacing the water pump can be found there. ( I checked) Hope this helps and best wishes.

Aug 18, 2009 | 1991 Toyota Corolla

2 Answers

Water Pump leakes from steel tube.


when installing new o-ring on tube, lubricate o-ring and stick it in water pump. Then pull pressure back on tube and then tighten hold down clamp. problem solved

Apr 16, 2009 | Dodge Caravan Cars & Trucks

1 Answer

Water outlet tube leaks


It inserts into back of water pump.Need I say more? Sorry.

Apr 11, 2009 | 1998 Plymouth Voyager

1 Answer

Heater hose coolant return tube


Yes you can remove the tube if its a V8. If its an inline 6 cylinder you have to remove the pump in order to repair the heater pipe.

Jan 29, 2009 | 1994 Jeep Grand Cherokee

2 Answers

WHERE IS THE WATER PUMP LOCATED ON A 1998 PLYMOUTH GRAND VOYAGER


Here are the steps required to change the water pump on the 3.0L engine.

  1. Disconnect the negative battery cable.
  2. Drain the cooling system.
  3. Remove the drive belts. Remove the timing belt covers and the timing belt.
  4. Remove the water pump mounting bolts.
  5. Separate the water pump from the water inlet pipe and remove the water pump.
  6. Inspect the water pump and replace as necessary.
To install:
  1. Clean all gasket and O-ring surfaces on the water pump and water pipe inlet tube.
  2. Wet a new O-ring with water and install it on the water inlet pipe.
  3. Install a new gasket on the water pump.
  1. Install the pump inlet opening over the water pipe and press until the pipe is completely inserted into the pump housing.
  2. Install the water pump-to-block mounting bolts and tighten to 20 ft. lbs. (27 Nm).
  3. Install the timing belt and timing belt covers. Install and adjust the drive belts.
  4. Reconnect the negative battery cable. Fill the cooling system to the proper level with a 50/50 mixture of clean, ethylene glycol antifreeze and water.
  5. Run the engine and check for leaks. Top off the coolant level, if necessary.
34bef4a.jpg

Jan 12, 2009 | 1998 Plymouth Grand Voyager

1 Answer

Where is the water pump on 93 geo prism, small engine


You're right. it could very well be your water pump, but I would suggest replacing your thermostat before trying to tackle replacing your water pump. However, if your thermostat turns out not to be the problem, I have enclosed step-by-step instructions for removal and re-installation of your water pump. Hope this proves to be helpful. Have a nice evening!


1993
Geo Prism Water Pump Removal/Installation
  1. Disconnect the negative battery cable. Drain the engine coolant from the radiator.
  2. Remove all drive belts.
  3. Support the engine using suitable equipment. Place a wooden block between the jack and engine. Remove the right engine mount and insulator.
  4. Remove the No. 3 (upper) and No. 2 (middle) timing belt covers.
  5. If equipped with power steering, raise and safely support the vehicle. Remove the front transaxle mount. Lower the vehicle, remove the cooling fan assembly.
  6. Remove the mounting bolt for the dipstick tube; remove the tube and dipstick. Immediately plug the hole in the block to prevent fluid from contaminating the oil.
  7. Remove the electrical connector for the coolant temperature sending unit.
  8. Remove the 2 nuts securing the engine coolant pipe to the cylinder block.
  9. Loosen the hose clamp and remove the coolant inlet pipe from the vehicle.
  10. Loosen the hose clamp and remove the coolant inlet hose from the water pump.
  11. If equipped with power steering, raise the engine and remove the mounting bolts for the water pump. Remove the water pump and O-ring from the vehicle.
To install:
  1. Install a NEW O-ring to the vehicle. Install the water pump and torque the retaining bolts EVENLY to 11 ft. lbs.
  2. Lower the engine if necessary, and connect the coolant hose to the water pump. Reconnect the engine coolant inlet pipe to the vehicle and secure to hose with clamp and secure to block with 2 nuts. Tighten the engine coolant inlet pipe nuts to 11 ft. lbs.
  3. Connect the electrical connector for the coolant temperature sending unit.
  4. Install the oil guide tube and torque the retaining bolt to 84 inch lbs. Install the oil level indicator to the guide tube.
  5. Install the radiator fan assembly, if necessary.
  6. If equipped with power steering, raise and safely support the vehicle. Install the front transaxle mount. Torque the through bolt nut to 64 ft. lbs. and 2 mount nuts to 47 ft. lbs.
  7. Lower the vehicle (if necessary) and install the No. 3 (upper) and No. 2 (middle) timing belt covers.
  8. Support the engine using suitable equipment. Install the right engine mount and insulator.
  9. Remove all engine lifting equipment.
  10. Install and adjust all drive belts.
  11. Reconnect the negative battery cable. Fill the cooling system. Start the engine and check for coolant leaks.

Nov 23, 2008 | 1993 Geo Prizm

Not finding what you are looking for?
1998 Plymouth Voyager Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...