Question about 1995 Geo Metro

2 Answers

Where can I get a wiring diagram for my 95 Geo Metro 4 cyl.? Starter solenoid not getting 12 volts to engage, seems as though it getting enough to click but not engage.

Posted by on

  • yadayada
    yadayada May 11, 2010

    the click you hear is a defective starter solenoid, that is what they do just click and starter does not engage.

  • yadayada
    yadayada May 11, 2010

    in a factory service manual.

×

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 32 Answers

If you get a Haynes repair manual it will have all of the wiring diagrams for the car.

Posted on May 31, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 433 Answers

I have one, what do you need to know?
Have you checked the battery?
Should be around 13-13.5 volts.

Posted on Apr 19, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the fuel pump and fuel filter located on a 95 geo metro lsi


Lay down along side the car by the drivers door. Look under the car and there is the fuel filter. It's strange by that's where it's located. Is your car a 1.3 L 4 cyl ? I know those engines like that back of my hand if you need further help.

Dec 13, 2014 | 1995 Geo Metro

2 Answers

93 geo metro will not start even though the battery is brand new and the alternator is okay. Manual transmission. Could it be the clutch pedal switch is bad???


do you mean it will not crank,
if it dont crank over at about 300 rpm
it will never start.
no the clutch switch only blocks, cranking.

Aug 01, 2013 | 1993 Geo Metro

1 Answer

Can I test my 99 honda solenoid while it attached to my car? Is there a trick to removing Honda solenoids?


Yes you can test it, if it clicks and starter doesn't engage then the solenoid is defective, if you have power to the solenoid and the ignition trigger wire lights up the 12 volt test light when the key is held to the start position you have either a defective solenoid or a defective battery OR battery cable connection,.

Aug 10, 2012 | Cars & Trucks

2 Answers

I am looking for a 95 geo metro secondary fuse box diagram


Check in autozone.com (free register) and go toChassis Electrical and Wiring diagram section.

Hope this help to solve your problem (remember rated this).

Apr 08, 2010 | 1995 Geo Metro

1 Answer

How do I test the fuel pump on a 95 geo metro? is there a wire to apply 12 volts to?


give these websites a try www.alldatadiy.com and www.autozone.com if all fails stop by your local library and get your hands on a Haynes auto repair manual for your car wish you the best of luck Michigan Man.

Jan 11, 2010 | Geo Metro Cars & Trucks

1 Answer

Changing starter on 97 geo metro 4 cyl 1.3


According to the tech maual, you get at it from underneath...these are the steps....removing the tire may help in having the "extra room".


  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle safely.
  3. Label and disconnect the starter solenoid electrical connector.
  4. Remove the mounting bolts from the starter motor, then carefully lower the assembly from the vehicle. To install:
  5. Install the starter motor assembly complete with any shims that may be used between the engine block and the starter.
  6. Install and tighten the starter mounting bolts to 17 ft. lbs.. (23 Nm).
  7. Connect the starter solenoid electrical connector.
  8. Lower the vehicle and connect the negative battery cable.

Aug 27, 2009 | 1997 Geo Metro

1 Answer

Clutch wont engage


The car won't move with it in gear and the clutch pedal out?

Mar 14, 2009 | 1995 Geo Metro

2 Answers

1991 Metro does not always start.


the safety switch under the clutch pedal is sticking.

Jan 23, 2009 | 1991 Geo Metro

1 Answer

Not firing at plugs or coil. new timing belt, cap, rotor,and coil


replace your distributer it has gone out. it happened to me and that is all it was.

Dec 27, 2008 | 1992 Geo Metro

Not finding what you are looking for?
1995 Geo Metro Logo

436 people viewed this question

Ask a Question

Usually answered in minutes!

Top Geo Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Mike Gilbreath

Level 1 Expert

50 Answers

Are you a Geo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...