Question about Honda CR-V

1 Answer

What kind of tail lite bulb needed for breaks

What kind of break lite bulb is in 2005 honda car

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 490 Answers

3157

Posted on Apr 13, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No break lights , replaced the break pedal switch , the tail light circuit boards and all bulbs , still no lights . and stop/haz fuse pops immediately when I youch the break ..... at a loss


You have a dead short and it could be any where from the front to the back of the car. It could be where a wire has a rubbed place in it or in the tail light assembly itself. According to what kind of vehicle it is it could be the multifunction switch. That is the most common cause

Nov 01, 2015 | Cars & Trucks

1 Answer

Everything works but my tail light, my break light works and so does the head lights


change the bulb the are two fillaments in the bulb one for the brake lite and one for the tail lite

Jan 22, 2012 | 2000 Hyundai Elantra

2 Answers

My tail lights are not working on my 2000 jetta the front lights work the break lights work and the blinkers work all inside lights work just fine


you need new bulbs in tail lights one bulb in each side has two elements one works brake other works running lights the elements in the bulb for tail lites are bad . so just replace bulbs. hope this helps.

Sep 13, 2011 | 2002 Volkswagen Jetta TDI

1 Answer

How do I take out the tail light of 2005 A6? I need to replace the break bulb.


Look inside the trunk on the side where the relative light cluster is that you require. There will be a cover there. Remove that and the light cluster will be accessible to replace the bulb. If the light cluster does not come away with the cover, carefully lift the plastic tab holding the cluster in place - they get brittle and can break very easily. Check the operation of the lights before replacing the cover.

Mar 08, 2011 | 2005 Audi A6

1 Answer

All fuses are good and bulbs tail lights even work. but no brake lights


Check the break switch under the break peddle. There sould be some kind of switch with a button on it that is always pushed untill you press the break peddle. The switch goes bad sometimes.

Feb 04, 2011 | Isuzu Pickup Cars & Trucks

1 Answer

Replacing the rear turn signal light bulb


yes, I just did the same, Don't try removing the tail lite itself, just lay on the ground reach your hand up there and turn the lite socket to realease and replace bulb. There is a tab holding the tail lite in place even after you take out the screws and it can break, if it does your tail lite maynot go back on correclty. Good look, it's actually very simple and quick

Dec 11, 2010 | 2006 Dodge Dakota

1 Answer

How to replace brake light bulb


  1. Open the back hatch of your Honda Pilot and look for two small screws. They will be right behind the tail light. Remove the two screws, using a standard screw driver. You should now be able to pull the tail light box away from the car a few inches to allow access to the sides of the tail light box

  2. Remove the two ball sockets found on both sides of the tail light box. At this point you should be able to move the entire assembly enough to get at the tail light. Inside the tail light you will find three bulb sockets. Remove all three bulbs by turning the sockets to the left.

  3. Then replace each break light bulb by screwing them clockwise into the sockets. Then, reassemble the tail light box in reverse order.
Hope this is a help PLEASE RATE MY HELP

Nov 28, 2010 | 2009 Honda Pilot

1 Answer

All, but one rear break lights are out on my 2005 Honda Odsseey and none of the dash board sensors are registering a probelm. Do I just need to purchase the light bulbs for the breaks?


You would have to check the bulbs first but it sounds like the bulbs are bad. If not you may have a wiring problem. Check the bulbs first before worrying or assuming a wiring problem. If bulbs are not the problem leave a comment and I'll get back to you.

Oct 13, 2009 | 2005 Honda Odyssey

1 Answer

Break light problem


Do you know if the brake light bulbs are working? (are the bulbs good?). (the bulbs have two parts, one for brake lights the other for running lights)
If the third brake light bulb is working the brake lights should be with good light bulbs.

Jul 22, 2008 | 2005 Honda Accord

1 Answer

How replace break light bulb in on a4 2005


Replacement of any bulb in the Tail-light assembly is easier then one thinks.

First thing you need to do is gain access to the trunk area. At the top of
the tail-light area inside the trunk is a small circle that needs to be
opened to expose the bolt that you need to remove.

WARNING: Be careful not to loose this bolt or you are going to have to take
apart your trunk interior to retrieve it.

After the bolt is removed the Tail-light assembly will pull out as follows;
Left side: pull out the right side of the assembly
Right side: pull out the left side of the assembly.
The out side of the assembly is held in place by 2 or 3 small nipples.

There will only be one cable that is connected to the assembly. This does not
have to be removed unless you really want to. On both sides of the assembly
there are 2 clips that hold the light plate to the break light lens. After
the clips are loosened the whole light bulb assembly can be removed and the
bulbs replaced.


Restoring the Break-light assembly.

After you have replaced your bulbs and re attached the the bulb assembly, you
will have to first fit the nipples on the outer side of the assembly then
push the inter side into place. Replace the bolt and tighten. You are done.

Jul 14, 2008 | 2005 Audi A4

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...