Question about 1996 Jeep Grand Cherokee

1 Answer

1996 jeep grand cherokee odometer stopped working

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

Make sure the contection on the back of your odometer is connected and is the cable connected to the transmission. If so might be the cable inside lube it with some WD-40 and should start working again.
Main thing to check are the connections.

Posted on Jun 06, 2009

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 726 Answers

SOURCE: 1996 Jeep Grand Cherokee - Will Not Start or Run

ok it has nothing to do with the gear box
no ower to your injectors check engine fuse
if and wen u took the gear box out did take the positive lead off?
if u did unplug the computer or try the reset so the computer can no the car is back togeather

Posted on Jul 19, 2008

motor1258
  • 6674 Answers

SOURCE: heated seat 1996 jeep grand cherokee

C1 & C2 in your panel are most likely one of the culprits, if no power at heater at seat. Sounds like testing for power at seat switch is easier to do than get at these circuit breakers in the panel. If you have power at switch at seat, then it's not the fuse/circuit breaker. Good reading at this link for you.


http://www.wjjeeps.com/seats/seats.htm#HEATED

Posted on Dec 29, 2008

  • 154 Answers

SOURCE: LOCATION OF LIGHTER FUSE FOR 1996 JEEP GRAND

If you have the owner's manual look up fuses in the index, good illustration. If you don't, I do. It shows a relay and a 15 amp fuse. Look at the passenger kick panel, pull the cover, and it is #2 fuse (second from the top on the left) The see the relay you may have to pull the panel (two screws and a clip) the relay is the third cavity down, third row from the firewal side.
Let me know if this works for you?

Posted on Apr 03, 2009

clarktravis8
  • 74 Answers

SOURCE: The interior lights for my 1996 jeep grand Cherokee Laredo

Hello and welcome to FixYa
The interior lights wont turn off cant because it can't get a conncetion definitely a headlight switch issue common problem for that make
Part # 05137535AA Headlight Switch Probably a dealer item very simple to change this yourself. Hope this gets you going.Please Rate Me. And you can always Ask Me.
1ak+f4pj7cbm32cuniyi2gaaaaaelftksuqmcc

Posted on Apr 27, 2009

  • 52 Answers

SOURCE: 1996 jeep grand cherokee limited v8 5.2, A/C instructions?

  1. Disconnect battery. This must be done to prevent accidental airbag deployment.
  2. Using on A/C recovery unit, remove all R-134a refrigerant from the A/C system. See: Service and Repair
  3. Remove the shift knob by pulling sharply upward.
  4. Place the transfer case in low range. Pry the shift indicator bezel out of the console using a trim stick.
  5. Apply the parking brake and place the transfer case in neutral. Remove the parking brake trim insert. Remove the console attaching screws. Lift the console up and disconnect the 4WD indicator lamp hamess. Remove the console.
  6. Remove the passenger side knee blocker. Remove the single end screw. Remove the screws below the glove box. Remove the screw at the courtesy lamp. Remove the ash receiver and the screws behind it. Remove the instrument panel armature screw behind the ash receiver. Open the glove box and remove the screws behind it. Lower the panel and disconnect the lamp harnesses. For additional instrument panel service procedures to complete steps 6 thru 25, refer to Instrument Panel, Gauges and Warning Indicators/ Instrument Cluster / Carrier/ Service and Repair/ Procedures. See: Instrument Panel, Gauges and Warning Indicators\Instrument Cluster / Carrier\Service and Repair
  7. Remove the pod switch bezels on both sides of the steering column with a trim stick.
  8. Remove the drive side knee blocker. Remove the end screw and screws located at the bottom of the knee blocker.
  9. Remove the cowl top trim panel by prying it up with a trim stick. Remove the solar sensor if equipped.
  10. Remove the "A" post trim panels.
  11. Remove the remove the bolts that attach the lower instrument panel reinforcement to the instrument panel armature and remove the reinforcement.
  12. Disconnect the park lamp switch.
  13. Pull back the carpet at the transmission tunnel from the base of the instrument panel center bezel. Remove the nuts from the upper studs and bolts through the floor that secure the instrument panel center bracket.
  14. Remove the bolts that secure the instrument panel center bracket to the drivers side of the transmission tunnel.
  15. Remove the screws securing the Vehicle Information Center and remove it. Remove the screw fastening the mounting bracket.
  16. Unplug the vacuum harness connector or vent tube on ATC equipped vehicles and the wire harness located under the passenger side of the instrument panel.
  17. Remove the screws holding the passenger side kick panel, along with the screw from the kick panel shroud.
  18. Unplug the antenna cable near the right cowl side panel.
  19. Unplug the instrument panel wire harness connectors from the junction block at the right cowl side panel.
  20. Remove the bolts that secure the instrument panel armature to the windshield fence.
  21. Remove the nuts that secure the top if the instrument panel armature to the windshield fence.
  22. Remove the bolts that secure the ends of the instrument panel to the cowl side panel.
  23. Remove the nuts that secure the steering column to the brake pedal support and lower the steering column.
  24. Remove the bolts that secure the instrument panel armature to the brake pedal support.
  25. Place a protective cover on the seats. Lift the instrument panel off the windshield fence studs and maneuver the instrument panel out and lower it onto the seats.
  26. Disconnect the refrigerant lines from the evaporator tubes. Make sure to install plugs or tape the ends of the lines and fittings to ensure that excessive amounts of moisture do not contaminate the A/C system.
  27. Remove the vacuum line at the tee from the main vacuum supply harness. This line runs through the body with the upper refrigerant line.
  28. Disconnect the heater hoses from the heater core and clamp the ends closed to prevent coolant loss. See: Heater Core\Service and Repair
  29. Remove the coolant overflow bottle.
  30. Remove the Powertrain Control Module with connectors intact and set aside.
  31. Remove the heater A/C housing mounting nuts from the studs on the engine compartment side of the dash.
  32. Remove the heater A/C housing from the vehicle.
  33. To Install the components, reverse the procedure stated above. Torque Specifications: Instrument panel center bracket to floor transmission tunnel fastener: 28 Nm (250 in. lbs.) Instrument panel to windshield fence bolts and nuts: 12 Nm (105 in. lbs.) Instrument panel to cowl side inner panel bolts: 12 Nm (105 in. lbs.) Instrument panel to steering column support bolts: 12 Nm (105 in. lbs.)

Posted on Aug 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1996 grand cherokee, turns over but will not fire as if no fuel,had full service done 1 month ago and started with being sluggish on start but if you turn ignition off and restart ok, now turns over but...


Try to check if some fault code is stored there, try self scanning the PCM (turn on, off, on, off, sna finally stay in ON ignition switch), note the codes in the odometer and sens ud details.

Keep in touch.

Oct 13, 2011 | 1996 Jeep Grand Cherokee

1 Answer

96 grand cherokee odometer is racking up miles realy fast and speedo does not show correct speed. still has stock tires.


likely you have the wrong gear in the speed sensor there are different ones available for different tires and differential gear ratios.

Jan 31, 2010 | 1996 Jeep Grand Cherokee

1 Answer

1999 jeep grand cherokee speedometer and odometer quick working


your speed sensor is on the side of the trany just go to you local parts house and look at the sensor you'll find it . it's realy that simple . hope this has been helpful to you !

May 30, 2009 | 1999 Jeep Grand Cherokee

1 Answer

1996 jeep grand cherokee


It probably means the number of miles it has been driven only the 0's have been left off!!
God Bless Greg

Nov 21, 2008 | 1996 Jeep Grand Cherokee

3 Answers

1996 Jeep Grand Cherokee - Will Not Start or Run


they have crankshaft sencers on the transmission on jeeps. it would be up high on the drivers side on front of transmission. they will cause it to not get fuel or fire and can run then quit.

Jul 19, 2008 | 1996 Jeep Grand Cherokee

Not finding what you are looking for?
1996 Jeep Grand Cherokee Logo

Related Topics:

291 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22258 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...