Question about 2003 Acura 3.2TL

1 Answer

How to change the windshield wipers on acura tl type s

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 43 Answers

If they are still the factory wipers, pull the black rubber inserts out, remove the 2 metal peice from the side of the rubber insert, install the metal into the new inserts. slide the insert into the blade. repeat for other side. i recommed that you use factory parts.

Posted on Sep 17, 2009

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

mrgreenz
  • 962 Answers

SOURCE: 1996 Acura 3.2 TL windshield wiper problem

they have what one guy, I know called a small "transmision" that engages both wipers and the speed. On one car the winshield wipers transmission connections were loose. A small bolt came off.
Check all the workings by running the wipers .
Try to get to the wiper motor assembly and take a look at it. You may have to remove some screws.

Posted on Dec 23, 2008

  • 14 Answers

SOURCE: how to change spark plugs on 2005 acura tl

Hi,

you need a 6 inch extension, short 3/8 ratchet, 5/8 plug socket, 3/8 swivel "u" joint, (sold at sears) 8mm 1/4 drive socket deep well and 1/4 inch ratchet.

find the coil packs (6 total, three in each head.)
remove the two retaining nuts holding each coil pack using 1/4 8mm socket and ratchet.
twist the pack to break the sticking boot below.
pull up (be careful to not rip the boots however it may still happen but rare.)
remove coil packs, the rear is a little more difficult with the intake.
use 6" extension and u joint and ratchet to remove plugs and replace.
reverse order to assemble. Good luck, and hoped this helped.

Posted on Jan 04, 2009

  • 13 Answers

SOURCE: 2003 Acura TL TypeS - heat and air not working

it's a wire from under the dash it usually burns out after awhile,i had the same problem email me at veron@sprint.blackberry.net for more info on the wire i forgot the name for it.

Posted on Jun 13, 2009

  • 417 Answers

SOURCE: ACURA TL SERVICE DUE SOON B1

It's a service interval reminder light that you should take your car to acura and have them perform the "b1" service. I would ask for an estimate first, and ask what that service includes. You may be surprised to find necessary and unecessary services. Some people view the b1 light as a way for Acura to get you car in there, quite possibly be charged for things you could probably do yourself.

Posted on Apr 16, 2010

  • 1 Answer

SOURCE: 1999 Acura TL - WIPER BLADES HIT HARD ON BOTH

I had this same problem. The wiper blades would extend too far and hit the edge of the car, or they wouldn't extend far enough and only wipe about 3/4 of the windshield. The problem was a broken Wiper Rod A. My local mechanic replaced it - the part was about $20 and the labor about $230. Have them look at wiper rod A

Posted on Oct 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My 2000 Acura TL wiper arms bang the cowling and pillar. What is wrong


might be someone took the whole arm off to paint em or whatever so while they are in the off position check to make sure they don't need a quick adjustment for example if they are flat/level with the windshield lower seal if they are than you got the wrong size blades if they are off a little than remove clip holding the windshield wiper arm and slide off of the cog and move it a couple teeth till its flat than check your work by turning the wipers on if they aren't perfect than keep adjusting till they are on both sides

Dec 31, 2014 | 2000 Acura TL

1 Answer

Acura tl 2001 wiper hit hard


the wiper control arms bushings are worn out and need replaced..

Feb 09, 2013 | 2004 Audi A4

1 Answer

Where is the location of acura tl 2004 wiper motor?


The wiper motor is located in the left rear of the engine compartment near the corner by the driver side. Remove the wiper arm assembly (both if necessary) and then remove the plastic cover at the edge of the hood near the windshield the motor is underneath. To remove the wiper arm flip up the small cover where the arm is attached and you will find a (12mm usually) nut. Remove the nut and work the arm off of the post using a rocking motion. Hope this helps.

Sep 02, 2011 | 2004 Acura TL

2 Answers

1999 Acura TL - WIPER BLADES HIT HARD ON BOTH SIDES, IS THERE AN ADJUSTMENT OR JUST REPLACE THE WIPER MOTOR


I had this same problem. The wiper blades would extend too far and hit the edge of the car, or they wouldn't extend far enough and only wipe about 3/4 of the windshield. The problem was a broken Wiper Rod A. My local mechanic replaced it - the part was about $20 and the labor about $230. Have them look at wiper rod A

Jan 09, 2010 | 1997 Acura TL Series

2 Answers

Windshield wipers don't work right. Try to and quit mid cycle.


YOUR WIPER MOTOR COULD HAVE BINDING LINKAGE AND PIVOTS.TRY LUBRICATE THEM WITH WD40.TRY NOT TO GET ANY ON WINDSHIELD.IF THIS DONT WORK WIPER MOTOR COULD BE FAULTY.

Sep 27, 2009 | 1996 Acura TL Series

1 Answer

1996 Acura 3.2 TL windshield wiper problem


they have what one guy, I know called a small "transmision" that engages both wipers and the speed. On one car the winshield wipers transmission connections were loose. A small bolt came off.
Check all the workings by running the wipers .
Try to get to the wiper motor assembly and take a look at it. You may have to remove some screws.

Dec 23, 2008 | 2000 Acura TL

Not finding what you are looking for?
2003 Acura 3.2TL Logo

Related Topics:

939 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...