Question about Chrysler Voyager

3 Answers

Blower resistor where is the blower resistor and how do you change it for a 2000 chrysler grand voyager

Posted by on

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Chrysler Master
  • 75,066 Answers

In the manual I have it is shown to be located under the hood at the rear of the compartment on the firewall area where there are several rectangular openings. The block is hidden from view below the wiper module on the lower edge of one of those openings. It has a 5 wire plug on the cabin side of the the opening. If you don't find it, then I know in the 2001 model it was in the cabin, behind the glove box again with the resistors sticking thru the firewall where the air intake would cool them. I just don't know in what year the block was moved between '98 and '01
If you find it in the first location you use a couple of flat blade screwdrivers to release the block and pull it into the engine compartment. On the hidden side push on a spring tang on the driver's side narrow edge of the block and on the comparment side you will see a couple of etched lines on that same side showing where to put the tip of the other screwdriver to pry it forward into the compartment.
Get a replacement block and install making sure the resistors aren't touching one another. If you have trouble removing it I can send you a page that shows what I described above. PS Please let me know where you find the resistor block to be located. Use the 'thank and rate' tab to get back to me quickly without having to wait for me to be "available"

Posted on Apr 13, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Where is the blower resistor at on a 2000 Chrysler T&C? It is not behind the glovebox.

Posted on Oct 19, 2009

  • yadayada
    yadayada Nov 23, 2011

    This is not the format to ask questions, it is to answer them.

×

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert
  • 50 Answers

The resistor is located on the firewall just inboard of the passenger side strut. Slide a screw driver inbetween the resister and firewall on the driver's side of the resistor and pry it out. There's supposed to be some lines there to guide you to where to put the screw driver. Also, check the connector. Frequently, with a resistor failure, the connector becomes melted and needs replaced as well.

Posted on Apr 13, 2009

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 67 Answers

SOURCE: Where physically is the blower motor resistor

open hood, at right side of vehicle underneath wiper module, at firewall, no need to remove wiper module.let me know if this help

Posted on Nov 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Heater wont blow on 2000 voyeger


Are you saying blower /fan not working at all? Checked fuses, and resistor?

Feb 10, 2014 | 2000 Chrysler Grand Voyager

1 Answer

Front heat only works on high sometimes


BLOWER RESISTOR BEHIND ALTERNATOR, CHANGE IT

Jan 21, 2013 | 2000 Chrysler Grand Voyager

1 Answer

My fan speed on heating is on fast wont turn down, change relay no good still the same ? help cheers adam.


exterior or interior "fan"

the most common for the interior is a defective blower motor resistor

most common for the exterior is a defective temp sensor or bogus A/C input to the PCM

Jun 03, 2010 | 2000 Chrysler Grand Voyager

2 Answers

I have a 2000 chrysler grandvoyager se and it 's got a problem the air conditioner only works in full speed how can i fix this problem


There is a blower resister,module ,it is bad,it is located near the blower motor,mounted on the outside of the blower case,but actually goes inside the blower box to keep cool,most of the time the blower motor is the cause for the resister to go out,the blower draws too many amps,even though it may seem it is fine,this is the cause for the resister failure.

Apr 23, 2010 | 2000 Chrysler Grand Voyager

1 Answer

2000 Chrysler Voyager blower motor replacement


When the Blower Motor Resistors on Chrysler, Dodge, Plymouth go out, the motor will work on High only.
They have made it a lot easier than the 80's models. I suggest buying a Haynes Manual or Chilton Manual available at most auto part stoes. They have step-by-step directions with diagrams and photos.
Based on your description: the motor is on it's way to total failure.

Dec 23, 2009 | 2000 Chrysler Grand Voyager

1 Answer

Where is the blower resistor on a 1999 Plymouth Grand Voyager


Under the hood on the firewall, far right side.Near the strut tower.

Dec 16, 2009 | 2000 Chrysler Grand Voyager

1 Answer

Could you tell me were is the heater fan resistor pack located on my chrysler grand voyager


I have a chevy truck and my plug to my fan plugged into the fan and the resistor on the other end does it look like there is a short plug the to the fan

Dec 12, 2009 | 2000 Chrysler Grand Voyager

1 Answer

Where physically is the blower motor resistor located for 2000 Chrysler Grand Voyager? Checked underneath glove box but underneath is encased in plastic. Need to remove plastics?


open hood, at right side of vehicle underneath wiper module, at firewall, no need to remove wiper module.let me know if this help

Nov 19, 2009 | 2000 Chrysler Grand Voyager

2 Answers

2000 Grand Voyager front A/C works off and on, back works good


check the condensor for debris, also check the front blower fan an its resistor, and again check your freon level

Aug 24, 2009 | 2000 Chrysler Grand Voyager

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

738 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...