Question about 2002 Kia Sedona

1 Answer

Misfire what does fault code u0doo mean

Engine misfire no six cylinder permanent fault code u0doo

Posted by on

  • andya35 Apr 13, 2009

    have changed spark plug, and injector cleared the fault codes and left with u0d00 does not misfire again until I drive it

  • Jimmy James May 11, 2010

    try changing the spark plug in that cylinder?

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

Hi,change the Mass Air Flow Sensor,that WILL cure it.
Cheers,
Phil.

Posted on Sep 08, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

4 Answers

I have a 2000 Dodge Stratus with a random misfire on 1,3 and 5. The engine runs fine besides a twitch in the motor that can be felt while idling. Already replaced plugs and wires. Suggestions?


get the OBD codes read this will tell you which switch/sensor is causing the issue , the last random misfire i encountered turned out to be low cylinder compression so if the OBD code says " random misfire " then get the cylinder compressions read , hope this helps

Apr 08, 2015 | 2000 Dodge Stratus

1 Answer

Engine Code 301


Code # 301??? That is NOT a valid Diagnostic Test Code (DTC) for the engine control system on a 2000 Mercury Sable.

Assuming that you mean P0301, that is a cylinder misfire code that is identifying number 3 cylinder as the cylinder with the misfire problem. MANY things can cause a cylinder to misfire including spark plugs, spark plug wires or boots, burnt valves, broken valve springs, blow head gaskets, cracked cylinder heads, bad or dirty injectors, faulty injector control circuits, Failed ignition coils...the list goes on....proper diagnosis required.

May 30, 2012 | 2000 Mercury Sable

1 Answer

I have a 2002 Jaguar X-type. The check engine light came on and it has been acting jumpy/shaky. I recently took it to be diagnosed and the codes I recieved back were P1314, P1316, P1111, and P0302..What do...


All fault codes can be checked out at http://www.bluejag.co.uk but here are the results for some of yours. You can ignor P1111. Looks like a faulty plug or coil pack cylinder 2

Fault Code:- P1314 Indicates a Power-train fault


The fault is generally due to a problem in the Ignition or Misfire area


Fault Description: Misfire rate catalyst damage -bank 2 NOTE: This DTC will flag only when accompanied by an individual cylinder misfire DTC: P0300 - P0306

Action of ECM:- ECM Default:- Maximum engine speed reduced


After clearing the DTC, complete the Misfire monitor drive cycle
Check for a reoccurrence of fault DTC.


Possible Fault:- Cylinder compression low Worn camshaft / broken valve spring(s) Fuel delivery pressure (low / high) Fuel injector(s) restricted / leaking Fuel injector(s) continuously open Fuel contamination Fuel injector circuit fault(s) (Injector DTCs also flagged) Spark plug failure / fouled / incorrect gap ECM to ignition coil primary circuit fault (Cylinder misfire detected DTC also flagged) Ignition coil failure
Fault Code:- P1316 Indicates a Power-train fault


The fault is generally due to a problem in the Ignition or Misfire area


Fault Description: Misfire excess emission NOTE: This DTC will flag only when accompanied by an individual cylinder misfire DTC: P0300 - P0306

Action of ECM:- none


After clearing the DTC, complete the Misfire monitor drive cycle
Check for a reoccurrence of fault DTC.


Possible Fault:- Cylinder compression low Worn camshaft / broken valve spring(s) Fuel delivery pressure (low / high) Fuel injector(s) restricted / leaking Fuel injector(s) continuously open Fuel contamination Fuel injector circuit fault(s) (Injector DTCs also flagged) Spark plug failure / fouled / incorrect gap ECM to ignition coil primary circuit fault (Cylinder misfire detected DTC also flagged) Ignition coil failure

Fault Code:-
P0302 Indicates a Power-train fault


The fault is generally due to a problem in the Ignition or Misfire area


Fault Description: Misfire detected ?€" cylinder 2

Action of ECM:- none


After clearing the DTC, complete the Misfire monitor drive cycle
Check for a reoccurrence of fault DTC.


Possible Fault:- Refer to P0300 Possible Causes

Aug 25, 2011 | 2002 Jaguar X-Type

1 Answer

Changed all spark plugs 2 coils still getting po316 and po305 what could be causing this f150 4.6 liter problem started after putting in a new fuel pump


Diagnostic Test Code (DTC) P0316 means that a cylinder misfire was detected within the first 1000 revolutions of the engine crankshaft after engine startup. This code will always be stored at the same time with freeze frame data and a fault code for the offending cylinder.
This is where DTC P0305 comes in.
This code means that cylinder #5 is the cylinder that is causing the misfire.
Coils and plugs are only two of the many possible reasons for a cylinder misfire.
The possible reasons for both of these codes are:
> Damaged crankshaft position sensor
> Ignition system (Primary or Secondary)
> Faulty fuel injector or fuel injector control circuit
> Poor fuel quality (will usually cause MULTIPLE cylinder misfire codes)
> Base engine faults (burned valves, low compression, damaged lifters or cam, blown head gasket, etc.)
> Damaged/malfunctioning PCM

NOTE: The LEAST LIKELY cause is the PCM. A damaged Crankshaft Position Sensor will usually cause problems on ALL cylinders, not a single cylinder, however it IS possible if the sensing ring is damaged.

Aug 09, 2011 | 2003 Lincoln LS

2 Answers

Engine yellow light is flashing and engine is not running smoothly


Hi It sounds like the engine management system has detected a fault. I`m assuming its a petrol engine and the most common problem is one of the coils has gone.
To find the exact fault the car needs to have a diagnostic check which will tell you which coil or other component has malfunctioned.
Good luck i`m sure it won`t be a big problem
John ( South Wales UK )

May 01, 2011 | 2004 Volkswagen Passat

1 Answer

CHUGGING ALONG WITH FLASHING CHECK ENGINE LIGHT....???? 2002 FORD WINDSTAR WHERE TO BEGIN


A flashing Check Engine light means you have a ignition Misfire, start by replacing the spark plugs and spark plug wires, one or more is defective. If you have a electronic engine control fault code reader the cylinder or cylinders that are misfiring will set a fault code, the codes are P0300-P0306, the last number being the number of the cylinder ( cylinders 1-6) the computer has detected a misfire in.

Apr 18, 2011 | 2002 Ford Windstar Cargo

1 Answer

2007 Volvo XC90 fault codes-ECM P030000, P030100, P030300, P0304000, what do they mean?


first code means random/multiple misfire cylinder (s) detected
second code means misfire detected number 1 cylinder, third code, miss=fire number 3 cylinder fourth code misfire number 4 cylinder
causes can be spark plugs, HT leads, ignition coils, injector, wiring fault, low compression/ engine mechanical fault

Jun 04, 2010 | 2007 Volvo XC90 V8 AWD Sport

1 Answer

1999 Nisian Maxima and need to know what codes mean?


P1320 Ignition Signal
Signal wire from distributor
P0325 Knock Sensor 1 Circuit Malfunction (Bank 1 or Single Sensor)
O2 senor ( The one before the cat converter )
P0300 Random/Multiple Cylinder Misfire Detected
The misfire detection monitor, a software strategy built into the computer, is designed to detect an engine misfire. The computer can also normally identify the specific cylinder in which the misfire has occurred. A misfire is nothing more than a lack of combustion, which can be caused by poor fuel quality or metering, low compression, lack of spark or unmetered air entering the engine. There are other possible, less obvious causes as well, such as uncommanded Exhaust Gas Recirculatin (EGR), flow. When the misfire monitor detects a misfire, it will trigger the check engine light with the specific cylinder number as the last digit in the P030X code. For instance cylinder 1 misfire is P0301, cylinder 2 is P0302 etc. In this case we have either multiple cylinders misfiring, or the computer simply can't determine the specific cylinder, and as such we are left with the P0300 in computer memory.
Possible Causes:
Fuel injectors, related wiring, sensors and computer issues
Running out of gas, or poor fuel quality
Evaporative emissions system (EVAP) concerns: fuel vapors leaking into engine
Incorrect fuel pressure

EGR system concerns: leaking EGR valve or restricted ports
Base engine concerns: low compression, valve train problems and timing issues
Ignition system concerns including, but not limited to:
Faulty spark plugs
Faulty coil or related wiring
Ignition module or related wiring issues
Ignition related sensor faults or wiring issues

Apr 13, 2009 | 1999 Nissan Maxima

1 Answer

Code u0doo


Anything that starts with a U usually means a computer communication problem.Does this displaed intermittently random or continously?

Aug 23, 2008 | 2001 Hyundai Elantra

Not finding what you are looking for?
2002 Kia Sedona Logo

Related Topics:

381 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76070 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...