Question about 2001 Jaguar S-Type

1 Answer

Rattle in front Brakes 2003 S-Type

Should there be a spring or similar to hold the front pads down?? Mine are rattling at every little bump. There is nothing holding down the pads to hold them in place... There are two pistons on the inboard side but nothing else... they are just floating around in the caliper...
Thanks so much....

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 13 Answers

There are two different types of brakes fitted if it has two guide pins you have to knock out there shoud be a cross shaped spring that goes under each pin and presses down on pads the other type there are two bolts you undo one and swivel the caliper up i think that type have springs on the pads

Posted on May 01, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rattle noise coming from front of my 2002 Chevy


FRONT BRAKE PADS ARE LOOSE IN THE CALIPER. MAY HAVE SOME OF THE ANTI RATTLE CLIPS MISSING OR CHEAP PADS

Sep 26, 2014 | Cars & Trucks

1 Answer

I have a 2006 ford fushion ...when I'm driving on the hwy there is no rattle..but if I'm on bumpy roads or hits bumps there is a rattle on the front right passenger side. But the rattle will quit if I step...


check that there are anti rattle springs behind the brake pads in the caliper on that side . When pads are replaced there is a spring plate that comes with the pads or there are little spring clips that are fitted with the pads to hold them securely in the caliper .. Compare one side with the other and see if there is anything missing on the problem side.

May 20, 2014 | Cars & Trucks

1 Answer

Front end noise


front brake pad hardware is worn out , causing pads to move around when jarred , applying brakes tightens pads and noise will go away

Jul 18, 2013 | 2007 Chevrolet Impala LS Sedan New Cars

1 Answer

I have a 2000 chevy malibu. I recently replaced the front brake pads. After this when driving down the road when i hit bumps something in the frontend rattles, i can hear and feel it.. when i hit or ride...


A loose pad could do it.
Check the pad anti-rattle clips again. The pads should be snug in the calipers. Its possible the new pads are not the exact same shape as the old ones.

Jan 14, 2013 | Cars & Trucks

1 Answer

My 2003 Ford focus is making a rattling sound by the driver side in the engine when I go over a bump or pot hole what could this be?


There are a number of things which can do that. If someone did not properly fasten the aircleaner down it will rattle. You can get a rattle out of the shielding for your Catalytic converters and sometimes gravel will get caught in the shielding and rattle with every bounce.

There is a good possibility the rattle is your front brake pads which is why they make a compound to glue the pad to the caliper. To check this, just lightly hit the brakes enough to make the calipers work and if the noise is reduced or stops, then that is your problem. Do this when going over the bumps and potholes.

Another possibility is the joint from the exhaust header to the Catalytic pipe. There is a round metallic gasket usually called a "donut" which can work loose with engine vibration. This will sometimes chirp when you go to Reverse and back to a forward gear.

I hope one of these will solve your problem.

Mar 06, 2011 | 2003 Ford Focus

1 Answer

How to change rear barke shoes


Brake Drums & Brake Shoes Removal & Installation To Remove:
Rear Drum Brakes kia-09-18-7627.gif

  1. Raise and safely support rear of vehicle.
  2. Release parking brake.
  3. Remove rear wheel assemblies. NOTE: If brake drum is stuck, install two 8 mm bolts into threaded holes and tighten evenly.
  4. Remove top return spring, front and rear shoe spring clips and hold-down pins.
  5. Remove anti-rattle spring and adjuster spring. NOTE: Note position of operating lever prior to removal.
  6. Remove bottom return spring.
  7. Remove clip and washer and detach parking brake cable from rear shoe.
  8. Remove brake shoes.
To Install:
  1. Lubricate all brake shoe contact points with appropriate grease.
  2. Place operating level into position on hub.
  3. Install rear brake shoe and connect parking brake cable to rear shoe with washer and clip.
  4. Install front brake shoe and install bottom return spring.
  5. Install hold-down pins and spring clips.
  6. Position operating lever and install top return spring.
  7. Install anti-rattle spring and adjuster spring.
  8. Install brake drum and screws.
  9. Adjust brakes and install rear wheel assemblies.
prev.gif next.gif

Jan 21, 2011 | 2003 Kia Spectra

2 Answers

I have a 2002 Passat V6 Wagon and the brakes and rotors were replaced (aftermarket parts) about 3 months ago. The CV boots were replaced 2 weeks ago. When I apply the brakes, about 3/4 of the way down,...


Check and see if the Brake Pads were re-installed with all the hardware, ie, Anti-Rattle Clips, shims etc. if your pads are not secure in the Calipers it will cause the pads to rattle when you are driving in effect causing your brakes to make weird noises, ie, groaning, squealing, rattling.

Sep 08, 2010 | 2003 Volkswagen Passat

1 Answer

Rear brake pads rattle


There are spring clips which keep the pads tight in the caliper. These spring clips are missing, or are broken, or have lost their tension, etc.

May 27, 2009 | 1997 BMW 328

1 Answer

Worn brake pads


Front brake pad exchange guide.

Step1 Park the Dodge Durango on a flat surface. Put the emergency brake on and put wedges behind the wheels to prevent the vehicle from rolling. Disconnect the negative battery cable from the battery. Drain 2/3 of the brake fluid from the master cylinder, using a syringe. Remove the wheel and the tire assemblies. Step2 Compress the caliper piston back into the caliper bore using a large C-clamp to drive the piston into the bore. Use additional force if it is required. Using a 3/8 inch hex wrench or socket remove the caliper mounting bolts. Step3 Rotate the caliper rearward off the rotor and out from its mount. Remove the inboard and outboard brake pads. Remove the spring clip that holds the inboard brakes in the caliper. Tilt the pad out at the top to unseat the clip. Remove the retaining spring that secures it in the caliper. Unseat one spring end and rotate the pad out of the caliper. Step4 Suspend the caliper assembly from the Durango frame using mechanic's wire. Do not allow the caliper assembly to dangle from the brake hose as this may damage the brake hose. Step5 Clean the surfaces of the caliper and steering knuckle with a wire brush. Apply multi-mileage grease or similar product. Using brake fluid or break cleaner clean the caliper slide pins. Apply a light coating of silicone grease to the pins. Step6 Install the inboard brake pad and it's spring. Install the outboard brake pad. Install the caliper over the rotor and seat it in its original position until it is flush. Using a torque wrench, torque the slide caliper pins to 22 ft./lbs. Step7 Add brake fluid to the master cylinder. Bleed the brakes. Reconnect the negative battery cable to the battery. Start the engine and pump the brakes 3-4 times to seat the brake pads. Reinstall the wheels. Test drive the Durango at slow to moderate speeds to ensure that the maintenance was performed correctly.
Rear brake pad exchange.

Step1 Lift the Durango off the ground with a car jack. Support the vehicle on all sides with jack stands. Keep children and small animals out of the vicinity when you replace the brakes. Step2 Loosen the lug nuts on the wheels with a torque wrench. Remove the wheel and tire assemblies and set them aside, face up, to prevent damage. Step3 Compress the caliper and remove it by lifting the top up and off the caliper adapter. Hang the caliper from the Durango's frame with mechanical wire. Step4 Remove the inboard and outboard brake shoes from the caliper adapter. Take off the top and bottom anti-rattle springs. Keep the springs separated, as they aren't interchangeable. Step5 Press the piston into the bore with a C-clamp. To prevent damage to the pistons, insert an old brake shoe in between the C-clamp and caliper piston. Remove the C-clamp. Step6 Wipe down the caliper mounting adapter and anti-rattle springs with brake cleaner. Grease the anti-rattle springs with brake grease. Install the bottom anti-rattle springs, followed by the top anti-rattle springs. Step7 Install the inboard brake shoes followed by the outboard brake shoes. Replace the caliper and the wheel and tire assemblies. Lower the vehicle to the ground and pump the brakes to seat the pistons.


Please rate and god bless:)


Apr 02, 2009 | 1999 Dodge Durango

1 Answer

Rattle from the front at low speed, think is from brake pads


Many times the spring clips, also known as anti-rattle clips are left out or broken, this will cause a rattle in the wheel area, this was the case on my Corvette after the brakes were done by the used car lot were I gought the car, I put a screw driver through the wheel spoke and pushed the pad up and down, it should not move easily.

Aug 06, 2008 | Jaguar XKR Cars & Trucks

Not finding what you are looking for?
2001 Jaguar S-Type Logo

160 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

yadayada
yadayada

Level 3 Expert

75744 Answers

SPEEDY CAR WORK SHOP...

Level 2 Expert

489 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...