Question about 2006 Toyota Sequoia

1 Answer

I need to reset my tire warning light and the service needed light. How do I do this???

I need to reset my tire warning light and the service needed light. How do I do this???

Posted by on

  • steve691 Apr 13, 2009

    i'll try and let you know!!

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert
  • 101 Answers

Your tires have pressure/temp sensors in them. Even the spare tire. Set them all at 35lbs. Most times people forget about the spare and it keeps the light on. Turn the key on and wait about 2 mins. The light should go out. Some Sequoias have a reset button under the steering wheel on the bottom of the dash. This sets the low pressure threshold and only needs to be reset if memory was scrambled somehow. Rare so don't worry about that now. If the light blinks on startup its possible you have a bad sensor in one of the tires and will need to checked at the dealer.
The MAINT light is reset with the little stem button you use to change the odometer from odo to trip 1 or 2. Set it to odo and turn the truck off. Push and hold the button while turning the key to on. The display will show -------------- Keep holding it until it changes to 0000000. The its reset for another 5k miles.


Posted on Apr 13, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ford Freestar Message Center not visible. Need help resetting tire warning light.


You can't reset the tire pressure warning light (TPMS), when the pressure is adjusted or the sensor replaced (if the warning is false) the light will go out, there is no reset. Check the air pressure in all the tires, they should be about 34 PSI all around.

Jun 03, 2016 | 2004 Ford Freestar

1 Answer

Why does tire light stay on 2011 Toyota?


Reset the Tire pressure monitoring system light. The reset button is located under the steering side under the finish panel. You have to bend down to see the button.
Operate the tire pressure warning system reset switch only after the inflation pressures of all 4 tires have been adjusted on the vehicle.
To initialize the system, press and hold the tire pressure warning system reset switch for 3 seconds or longer with the power switch turned IG-ON

Jul 23, 2014 | 2011 Toyota Highlander

1 Answer

Tyre Pressure and ABS


By operating the tire pressure warning system reset switch, tire pressure warning system ECU can be set to issue a warning at an inflation pressure that corresponds with the type of tires.
Operate the tire pressure warning system reset switch only after the inflation pressures of all 4 tires have been adjusted on the vehicle.
To initialize the system, press and hold the tire pressure warning system reset switch for 3 seconds or longer with the power switch turned IG-ON. When starting the initialization, the tire pressure warning light blinks 3 times at 0.5 Hz.
During the initialization, the tire pressure warning system valve & transmitter measures the inflation
pressure of the tires, and registers the signals that are transmitted into the ECU at a frequency of 1 per
minute. The initialization process is completed when the signals from the tires have been received.
Once the tire pressure warning system reset switch has been pressed, do not turn the Ignition switch OFF for a few minutes.

Mar 05, 2014 | 2002 Toyota Corolla

1 Answer

I changed 1 of my valve sensor so i need to no how to reset the tpms light


By operating the tire pressure warning reset switch, the tire pressure warning ECU can be set to issue a warning at an inflation pressure that corresponds to the standard pressure of tires .Therefore, you must set the warning threshold to the proper value in order to comply with the local regulations .Operate the tire pressure warning reset switch only after the inflation pressures of all tires have been adjusted on the vehicle.To initialize the system, press and hold the tire pres- sure warning reset switch for 3 seconds or longer with the ignition switch in the ON position. When the system receives the
initialization signal, the warning light blinks 3 times (1 second on, 1 second off). During initialization, the tire pressure warning valve and transmitter measures the inflation pres sure of the tire, and registers the signals that are transmitted into the tire pressure warning ECU at a frequency of once per minute. The initialization process is completed when signals from all the tires have been received. It takes a few minutes .

Tire size Inflation Front Inflation Rear
P 195/65 R15 89S 30 psi 30 psi
195/65 R15 91H

P 205 /55 R16 89H 32 32 psi
P 215/45 R17 87W
205/55 R16 91V

Dec 10, 2013 | 2010 Toyota Corolla 2.0

4 Answers

Tire warning light won't go off - Tires are correct pressure


it needs to be reset, here is the procedure>>>http://library.motoralldata.com/techRef/WebHelp/Tire_Pressure_Monitor_Reset_Procedures/Toyota/2005-2006_Solara.htm

Aug 10, 2010 | 2006 Toyota Solara

1 Answer

Tire pressure monitoring system needs service since it stays on. I had tires rotated recently an8d there were warnings. I had them reajust tire pressures 80 back and 55 front. A new light came on that...


Check to see if the sensors are reconnected. If they are, lower rear tire pressure to 55 to 60 and recheck status light. You will have to turn the engine off and back on to reset.

That is a stretch but it has worked for me on other Chev models.

P.S. Confirm 55 x units mbar KPa Psi with tire pressure gauge.

Jan 16, 2010 | 2008 Chevrolet Express

1 Answer

Changed right front tire now reads zero on dash light is on


Your tire pressure monitor needs to be reset whenever you change or rotate your tires...

1. check and make sure that your tires are inflated to the correct pressure

2. turn the ignition switch to the ON position. If the low tire pressure warning light comes on, push and hold the tire pressure warning reset switch (think the switch is in the glovebox, but not sure) until the warning light turns off and then release the switch.

3. now press and hold the tire pressure warning reset switch until the low tire pressure warning light blinks three times.

4. initialization is *not* completed until driving at the vehicle speed of 19 mph or over for more than one hour. the tire pressure monitoring starts when initialization is completed.

Aug 24, 2009 | 2008 Chevrolet Tahoe

2 Answers

08 CALIBER ORANGE WARNING LIGHT ON, CANNOT FIND OUT WHAT IT IS


this would be a low tire symbol have you tire pressure check it will come on when one off your tires get a little low. the light will reset itself after the proper tire inflation is put in ..thanks for choosing fixya

Mar 03, 2009 | 2008 Dodge Caliber

1 Answer

Tire reset on in ford freestar


Reset without message center:
To reset turn the ignition to the ON position, depress and Trip/odometer
button (located in the instrument cluster) until “TIRE RESET” or
“CHECK TIRE AND RESET” is displayed in the odometer display window.
Once “TIRE RESET” or “CHECK TIRE AND RESET” is displayed,
press and hold the button for three seconds. The low tire warning indicator light will flash three times
as the low tire warning system begins to initialize.

------------------------------------------------------------------------
Reset with message center:
To reset turn the ignition to the ON position, press the set up button on
the message center until “SYSTEM CHECK” is displayed. Press the
RESET button until “HOLD RESET TO RELEARN” is displayed, continue to hold the button for three
seconds. The low tire warning indicator light will flash three times as the low tire warning system begins to initialize.

Oct 13, 2008 | 2005 Ford Freestar

1 Answer

Tire pressure monitor


32 psiis actually low for a 3500. I have a 1500 silverado that runs 44 psi cold. The tire inflation monitor , monitors inflated cirunference. Sooooo, If it isn'nt round enough, it will let you know. Driving warms up both the air and the tire,off course changing everything again. Pressure is up and tire is bigger. Ask me not how it can tell what is going on with the tire sitting still. I'm only on page 9,000, the answer is here somewher. :-) Well good luck. I do know the above is accurate._Ned_

Jun 26, 2008 | 2004 Chevrolet Silverado 3500

Not finding what you are looking for?
2006 Toyota Sequoia Logo

729 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8567 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...