Question about 1992 Toyota 4Runner

1 Answer

Torque settings what is the touque settings for a 1992 v6 4runner

Posted by on

  • hmrdsmith Apr 13, 2009

    the head bolts

  • Dave  C
    Dave C May 11, 2010

    For which fastener?

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,050 Answers

You have to use new headbolts because they are torque to yield bolts. You start in the middle and criss cross out to the ends with an initial torque of 33 ft-lbs. Then you criss cross out out again with an additional 90 degrees on each bolt, then you do it again from the middle another 90 degrees to make a total of 180 degress past the initial 33ft-lbs.

Posted on Apr 13, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need the touque specs for the outer front axle nut on a 2005 dodge ram 2500 4x4


HUB AND BEARING ASSEMBLY NUTS TORQUE TO 125 FT LBS THE HALF SHAFT AXLE TORQUE TO 185 FT LBS.

Oct 16, 2010 | Dodge Ram 2500 Cars & Trucks

1 Answer

What is the touque for the wheel bearing?


you can call the dealer and get the specifics.. but i've never torqued a wheel bearing, just tighten the nut with a 1/2 " ratchet and rolled the wheel to make sure it wasn't too tight. hope that helps

Mar 19, 2010 | 2004 Buick Rendezvous

3 Answers

Need head bolt, intake manifold, and exhaust torque specs


Cylinder Head Bolt Step1- (25 FT.Lbs) Step2(45 Ft.Lbs) Step3(65Ft,Lbs).....Intake Manifold(35Ft Lbs)....Exhaust Manifold Center (20Ft Lbs) All Others (20 Ftlbs).....Thanks

Mar 06, 2010 | GMC Suburban Cars & Trucks

3 Answers

For tightening head bolts on my car it says to tighten to 37 ft. lbs. then, using a torque angle meter, rotate an additional 130 degrees. why do they use ft. lbs. and degrees?why not all in ft. lbs.?


Because, by the time you twist that bolt to let's say, 65ft.lbs, it could snap.

The manufacturer of that bolt knows that if the bolt is torqued, (Stretched) to a certain torque value, and is turned a certain amount of degrees, the proper torque value will be reached, and still stay within the guidelines of the tensile strength of the bolt.

Torque is set to Bolt Stretch. How far the bolt will stretch in a given torque value, and not exceed it's tensile strength. The threads are stretched over to one side a little also, and this causes the bolt to be locked into position. They can only be 'tweaked' over to one side so many times, then they will fail.

Also the bolts have a certain tensile strength, and can only be stretched so far, and So may times.
MANY, manufacturers plainly state to not reuse a head bolt of this nature. Reasoning, is that the bolt has been stretched, and stretching it again may cause failure of the bolt.

Plus, every time the engine reaches the operating temperature, it stretches the bolts, then the bolts contract once the engine has cooled off.
[Everything you always didn't want to know, huh?]

Aug 18, 2009 | 1999 Oldsmobile Intrigue

1 Answer

Puting back head on mitzy 4g13 need touque settings for head stud


try autozone.com to see if they have your car listed for diagrams pictures and step by step instructions if your car is not listed then try your local library they have all the car manuals and even copy them for you

Mar 21, 2009 | 2002 Mitsubishi Lancer

2 Answers

Spark plug change


Well i wouldent of thought you need to take off the valve cover AKA (rocker cover) to change spark plugs. spark plugs are usally set at a touque setting at 10 to 15 NMs (newton meters). if you do have to take off the valve cover the gasket can be re-used no O-rings needed.

Mar 06, 2009 | 1994 Nissan Altima

1 Answer

Head bolt touqe settings


Tightening torques

Do not reuse the bolts as they may be stretched.

Cylinder head to engine block
Stage 1: 32Ft-lbs
Stage 2: +90degrees
Stage 3: +90degrees

Cylinder head to lower timing
chain cover: 89in-lbs

Nov 27, 2008 | 1992 BMW 3 Series

Not finding what you are looking for?
1992 Toyota 4Runner Logo

Related Topics:

186 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...