Question about 2002 Mitsubishi Montero

1 Answer

Help change fan belts on Mitsubishi pajero nm 202 mod can`t undo pully nut is it left or right handed thred

Posted by on

  • Anonymous Mar 28, 2014

    I have number 1 piston tdc

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Mitsubishi Master
  • 3,854 Answers

First job is to remove the 4 bolts securing the Intercooler, Its not totaly necessary to remove, but makes it a lot easier to get to the pullies.

Remove the 4 Bolts and move the Intercooler to the left hand side of the engine

Loosen off the locking bolt on the centre of the pully and then loosen the adjuster bolt until belt slackens

Loosen off the forward facing locking bolt and then loosen the adjuster bolt (Hidden behind the top hose) until belt slackens

You should now be able to remove all the belts and replace as required.

On refitting the belts adjust as required and then do up the locking bolts, refit Intercooler and check all connections (you wouldn't like the intercooler fan to fail

Its as easy as that, Good luck and not be held responsible for any 'misfortunes' in carry out the job like breaking out in to a sweat.

Posted on Apr 13, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace fan belt on a Mitsubishi pajero


Instructions
  1. 1 Open the bonnet of the Pajero, and turn the bolt on the centre of the tension pulley with a socket wrench two full rotations. The tension pulley is the pulley directly behind the fan in the upper portion of the front of the engine.
  2. 2 Loosen the adjuster bolt on the tension pulley bracket. This bolt is on the left-hand side, situated in a long horizontal groove.
  3. 3 Slip the fan belt off of the engine. Draw a diagram of the path of the fan belt if the factory printed sticker diagram is no longer in the front of your engine on your Pajero.
  4. 4 Insert the new fan belt, winding it through the various pulleys according to your diagram. Put it on the tensioner pulley last.
  5. 5 Place the tension belt tool on the tension pulley bolt and pull until the slack in the belt is gone. When there is no slack, keep the pressure on the pulley, and tighten the adjuster bolt with the wrench. Tighten the lock bolt on the pulley.

Jun 17, 2015 | 2006 Mitsubishi Pajero 3.2

1 Answer

How do i check on auto gear box oil on 1989 mitsubishi pajero


possibly a dipstick in engine bay. if not undo the nut at the side of gearbox..

Feb 26, 2015 | 1986 Mitsubishi Pajero

1 Answer

A diagram of how to fit serpentine belt to 2002 np pajero


can someone post diagram for fan belt of NM PAJERO 2000, 3.5 auto

Jun 18, 2012 | Mitsubishi Pajero Cars & Trucks

1 Answer

How do I remove and replace the left hand tie rod on my 2003 Civic Honda


take off the wheel undo the nut . undo the lock nut at the end of shaft to tie rod then with a hammer hit the eye were the joint bolts through not the thred the shock will make it pop out some times u need 2 hamers one on the other side of were u are hitting .. once loose mark were the old one was scrood to and replace in the same spot then bolt all back to gether it is very easy

Apr 11, 2011 | Honda Civic Cars & Trucks

1 Answer

1997 nissan quest changing timing belt is nut that holdes the bottom pulley on left handed or right handed


the harmonic pulley bolt is right hand thread and is sometimes very tight to undo.

Mar 26, 2011 | Nissan Quest Cars & Trucks

2 Answers

What is the correct tyre pressures for a 1992 mitsubishi pajero V6 3000


The vehicle specifics are located insde the driver side door jam. Look for a sticker. If not, look for the tire pressure ratings and pressure specifics on the tire(s).

Jan 09, 2011 | Mitsubishi Passenger Cars & Trucks

1 Answer

View of mark for timing belt.


hi from uk the cambelt/timing belt comes as a kit ie timing belt and tensioner cost £50 here in uk ? it is not too difficult diy job approx 2hours the engine must 1st be set to TDC number 1 firing then at this setting the cam cog mark is a hole drilling in the web of cog and should line up at 12 oclock upwards and using a mirror look thro drill hole and you will see a vertical notch/groove behind on font engineface this is correct mark the crank cog mark lines up with aother mark on engine front face at approx 12 30 pm oclock ? if now set you slacken tensioner bolts and push t/pully away to left from belt ? then remove belt next remove complete tensioner assy after undoing bolts then fit new tensioner push t/pully to left from belt run and lock bolt/s recheck t/marks then fit new belt from c/shaft in anticlockwise rotation when fitted release tensioner bolt and allow to tension belt push t/pully onto belt and lock up tensioner bolts20=27 Nm rotate engine manually for four turns then recheck marks ? should still aligne then re assemble torque crank bolt to =140-150 Nm A LITTLE HINT ? b4 you remove the water pump belt ? slacken thefour 10 mm headed bolts (spanner size) that secure w/pump pully to pump it will be easier to halt rotation of pully if you holt belt tight by hand this pully has to come off to remove c/belt covers same for power steer belt which is also driven from the w/pump pully the power steer pump slide adjuster has a 12 mm bolt you slacken and best done with open end spanner ? after slackening the pump mounting bolts/nuts underneath pump hope you can follow this info/tips wish you good luck from uk

Apr 09, 2010 | 2000 Hyundai Accent

1 Answer

Replacing alternator on 91 nissan 300zx


first jack up car then look on the passenger side of the car to find the alternator. there is a bracket right next to the crank pully going to the alternator. it is only one bolt. undo it. there is i believe a 15 mill bolt on top of the alternator with a lock nut on the back almost out of reach from the bottom. undo the bolt and the alternator will drop down into your hands. there is the tensioner bolt to tighten the belt on the bottom of the alternator you can loosen it up to make things easier on you. when the alternator is loose pull out gently as there is one clip connection and two ground bolts on the back of the unit itslef. undo all of these and slide your alt out the front. it may be easier to remove the clutch fan on the water pump pully first. (4 nuts)

Nov 22, 2009 | 1991 Nissan 300ZX

1 Answer

Pajero


No, timing chains are not expected to be replaced periodically like belts. Ocassionally they get noisey at high mileages and require a new tensioner pad but usually the chain is OK with a new pad

Jun 27, 2008 | 2002 Mitsubishi Montero

Not finding what you are looking for?
2002 Mitsubishi Montero Logo

912 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...