What torque should the bolts securing the lower suspension strut to the stub axle assembly be done to? (19 mm bolts)

front

1. Install or connect the following:
   • Strut assembly
   • Fork to the strut and torque the bolts to 59 ft. lbs. (80 Nm)
   • Fork to the lower arm and torque the bolt to 88 ft. lbs. (120 Nm)
   • Upper strut mounting nuts and torque to 36 ft. lbs. (50 Nm)
   • Brake hose bracket
   • Front wheel
2. Check and/or adjust the wheel alignment.

--------------------rear------------

To install:

1. Install or connect the following:
   • Strut assembly and mounting bracket and torque the bolt to 36 ft. lbs. (50 Nm)
   • Upper arm and rear carrier bolt and torque the bolt to 88 ft. lbs. (120 Nm)
   • Lower mounting bolt
   • Rear wheel

no engine stated, they even have diesel. or 3.7L GAS.
I toss my first coil, land on 3.7L V6.
great question, like the very first ever.
most just do it and get in trouble. vast posts in this.
but whats up, what is wrong, what part failed.?
this is best to know, so we can send you the official chapter on this from jeep.
sure use jackstands, never jacks only and never bricks .
04,KJ jeep 4wd pan off.
in chapter 9 ,under diagnostics, and pan leaks. that?
it says read
Refer to 9 -
ENGINE/LUBRICATION/OIL PAN -
REMOVAL). page 1555 (3.7L)
and i quote:
REMOVAL
1. Disconnect and isolate negative battery cable.
2. Install engine support fixture.
3. Raise and support vehicle.
4. Remove front wheel assemblies.
5. Remove skid plate (if equipped). (Refer to 13 -
FRAME & BUMPERS/FRAME/FRONT SKID
PLATE - REMOVAL)
6. Drain engine oil.
7. Mark adjustment cam position of front lower control
arm bolts.
8. Remove front lower control arm bolts. (Refer to 2 -
SUSPENSION/FRONT/LOWER CONTROL ARM -
REMOVAL)
9. Disconnect LH tie rod. (Refer to 19 - STEERING/
LINKAGE/TIE ROD END - REMOVAL)
10. Disconnect LH lower ball joint (Refer to 2 - SUSPENSION/
FRONT/LOWER BALL JOINT -
REMOVAL)
11. Disconnect LH strut clevis (Refer to 2 - SUSPENSION/
FRONT/CLEVIS BRACKET - REMOVAL)
12. Remove LH front axle (Refer to 3 - DIFFERENTIAL
& DRIVELINE/HALF SHAFT - REMOVAL)
13. Remove front axle brace bolts.
14. Remove front prop shaft. (Refer to 3 - DIFFERENTIAL
& DRIVELINE/PROPELLER SHAFT/
PROPELLER SHAFT - REMOVAL)
15. Drain front axle.
16. Using a transmission jack, support front axle.
17. Remove axle bracket bolts. (Refer to 3 - DIFFERENTIAL & DRIVELINE/FRONT AXLE - REMOVAL)
18. With RH axle still in place, remove front differential.
19. Remove transmission oil cooler line bracket.
20. Remove engine to transmission stiffening bracket.
21. Position Special Tool 8534 on fender lip and align the slots in the brackets with the fender mounting holes.
22. Secure brackets to the fender using four M6 X 1.0 X 25 MM flanged cap screws.
23. Tighten the thumbscrews to secure the sleeves to the support tube.
24. Secure the support tube in an upright position.
25. Assemble the flat washer, thrust bearing, hook and T handle.
26. Using the M10 X 1.75 mm flanged nut supplied with the support fixture, secure the chain to the front engine
lifting stud.
27. Loosen engine mounts.
28. Remove oil pan bolts.
29. Seperate oil pan (1) from engine.
30. Move oil pan to one side, remove oils sump bolt and windage tray bolts,
NOTE: Do not pry on oil pan or oil pan gasket. Gasket is integral to engine windage tray and does not come
out with oil pan.
end quote, (off)

Hi Douglas, I'm glad to help. My first suggestion is to get to complete shaft. This way you want have any problems later on. It's not that much more expensive and you'll be glad you did. Below is the procedure for replacing them.

FRONT DRIVESHAFTS

REMOVAL

1. Raise vehicle on jack stands or centered on a frame contact type hoist. Refer to Hoisting in the Lubrication And Maintenance section of this manual for the required lifting procedure to be used for this vehicle.
2. Remove the cotter pin and nut lock Hub And Bearing To Stub Axle Retaining Nut from the end of the stub axle.
3. Remove the wheel and tire assembly from the vehicle.
4. Remove the wave washer Wave Washer from the end of the stub axle CAUTION: Wheel bearing damage will result if after loosening hub nut, vehicle is rolled on the ground or the weight of the vehicle is allowed to be supported by the tires.
   
5. With the vehicle's brakes applied to keep hub from turning, loosen and remove the stub axle to hub nut.
6. Remove the two front disc brake caliper to steering knuckle attaching bolts Front Disc Brake Caliper Attaching Bolts
7. Remove the disc brake caliper from the steering knuckle. Caliper is removed by first rotating top of caliper away from steering knuckle and then removing bottom of caliper out from under machined abutment on steering knuckle Brake Caliper Mounting To Steering Knuckle
8. Support disc brake caliper assembly by using a wire hook and suspending it from the strut assembly Correctly Supported Disc Brake Caliper Do not allow the brake caliper assembly to hang by the brake flex hose.
9. Remove the brake rotor from the hub and bearing assembly Remove/Install Brake Rotor
10. Remove nut attaching outer tie rod end to steering knuckle Removing Tie Rod End Attaching Nut Nut is to be removed from tie rod end using the following procedure, hold tie rod end stud with a 11/32 socket while loosening and removing nut with a wrench.
11. Remove tie rod end from steering knuckle using Remover, Special Tool MB-991113 Tie Rod End Removal From Steering Knuckle Arm
12. Remove the steering knuckle to ball joint stud, clamping nut and bolt Control Arm To Steering Knuckle Attachment from the steering knuckle.
13. Using a pry bar, separate steering knuckle from ball joint stud Separating Ball Joint Stud From Steering Knuckle Note: Use caution when separating ball joint stud from steering knuckle, so ball joint seal does not get cut. NOTE: Care must be taken not to separate the inner C/V joint during this operation. Do not allow driveshaft to hang by inner C/V joint after removing outer C/V Joint from the hub/bearing assembly in steering knuckle, end of driveshaft must be supported.
    
14. Pull steering knuckle assembly out and away from the outer C/V joint of the driveshaft assembly Steering Knuckle Separation From Driveshaft
15. Support the outer end of the driveshaft assembly. Insert a pry bar between inner tripod joint and transaxle case Disengaging Inner Tripod Joint From Transaxle Pry against inner tripod joint, until tripod joint retaining snap ring is disengaged from transaxle side gear.
16. Hold inner tripod joint and interconnecting shaft of driveshaft assembly. Remove inner tripod joint from transaxle, by pulling it straight out of transaxle side gear and transaxle oil seal Tripod Joint Removal from Transaxle When removing tripod joint, do not let spline or snap ring drag across sealing lip of the transaxle to tripod joint oil seal.

INSTALLATION

1. Thoroughly clean spline and oil seal sealing surface, on tripod joint. Lightly lubricate oil seal sealing surface on tripod joint with fresh clean transmission lubricant.
2. Holding driveshaft assembly by tripod joint and interconnecting shaft, install tripod joint into transaxle side gear as far as possible by hand Tripod Joint Removal from Transaxle
3. Grasp inner tripod joint an interconnecting shaft. Forcefully push the tripod joint into side gear of transaxle, until snap ring is engaged with transaxle side gear. Test that snap ring is fully engaged with side gear by attempting to remove tripod joint from transaxle by hand. If snap ring is fully engaged with side gear, tripod joint will not be removable by hand.
4. Clean all debris and moisture out of steering knuckle, in the area were outer C/V joint will be installed into steering knuckle.
5. Ensure that front of outer C/V joint which fits against the face of the hub and bearing is free of debris and moisture before installing outer C/V joint into hub and bearing assembly Outer C/V Joint Inspection
6. Slide drive shaft back into front hub and bearing assembly. Then install steering knuckle onto the stud of the ball joint assembly Steering Knuckle Separation From Driveshaft
7. Install a new steering knuckle to ball joint clamping bolt and nut Control Arm To Steering Knuckle Attachment Tighten the clamping bolt and nut to a torque of 135 N·m (100 ft. lbs.)
8. Install tie rod end into steering knuckle. Start attaching nut onto stud of tie rod end. While holding stud of tie rod end stationary using a 11/32 socket, Removing Tie Rod End Attaching Nut tighten tie rod end to steering knuckle attaching nut. Then using a crowfoot and 11/32 socket Torquing Tie Rod End Attaching Nut , tighten the tie rod end attaching nut to a torque of 54 N·m (40 ft. lbs.)
9. Install braking disc on hub and bearing assembly Remove/Install Brake Rotor
10. Install disc brake caliper assembly on steering knuckle. Caliper is installed by first sliding bottom of caliper under abutment on steering knuckle, and then rotating top of caliper against top abutment Brake Caliper Mounting To Steering Knuckle
11. Install disc brake caliper assembly to steering knuckle attaching bolts Front Disc Brake Caliper Attaching Bolts Tighten the disc brake caliper assembly attaching bolts to a torque of 22 N·m (195 in. lbs.)
12. Clean all foreign matter from the threads of the outer C/V joint stub axle. Install the washer and stub axle to hub/bearing assembly nut on stub axle and securely tighten nut.
13. Install front wheel and tire assembly. Install and tighten the wheel mounting stud nuts in proper sequence until all nuts are torqued to half the required specification. Then repeat the tightening sequence to the full specified torque of 135 N·m (100 ft. lbs.)
14. Lower vehicle.
15. With the vehicle's brakes applied to keep hub from turning, tighten the hub nut to a torque of 244 N·m (180 ft. lbs.) Torquing Front Stub Axle To Hub Nut
16. Install the spring wave washer on the end of the stub axle.
17. Install the hub nut lock, and a new cotter pin Hub And Bearing To Stub Axle Retaining Nut Wrap cotter pin prongs tightly around the hub nut lock as shown in Hub And Bearing To Stub Axle Retaining Nut
18. Check for correct fluid level in transaxle assembly. Refer to Group 21, Transaxle for the correct fluid level checking procedure for the type of transaxle being checked.
19. Set front toe on vehicle to required specification.

• Air Suspension
• Front Suspension
• Rear Suspension
• • Coil Spring Rear Suspension
  • Coil Springs
  • Lower Ball Joint
  • Lower Control Arms
  • Shock Absorbers
  • Stabilizer Bar Sway Bar
  • Strut Macpherson Strut Assembly
  • Upper Control Arms
  • Wheel Bearings
• Specifications
• Wheel Alignment

• HOME
• REPAIR INFO
• 1999 LEXUS ES300 3.0L SFI DOHC 6CYL REPAIR GUIDE
• SUSPENSION
• REAR SUSPENSION
• COIL SPRING REAR SUSPENSION

Lexus Car ES, IS, LS 1998-06
Coil Spring Rear Suspension

• HUB & BEARINGS
• STABILIZER BAR
• STRUT & COIL SPRING

Print

Hub & Bearings

Adjustment
Check the backlash in bearing shaft direction and the axle hub deviation. Maximum for backlash should be 0.0020 in. (0.05mm) and for axle hub deviation 0.020 in. (0.05mm).

Fig. Checking wheel bearings for excessive play


NOTE The rear wheel bearings are non-adjustable. If the wheel bearing is out of specifications, replace the wheel bearing.
Removal & Installation

1. Before servicing the vehicle, refer to the Precautions section.
2. Raise and safely support the vehicle.
3. Remove or disconnect the following:
   
   Rear tire and wheel assembly Rear stabilizer link Rear axle shaft nut Rear disc brake caliper and disc Speed sensor Parking brake assembly at the wheel hub No. 1 and 2 upper control arm assembly No. 1 and 2 rear suspension arm assembly Toe control link Rear axle from hub assembly using a plastic hammer No. 2 rear wheel bearing dust deflector using a screwdriver 4 bolts and rear axle hub and bearing assembly from the axle carrier assembly
   

To install:

1. Install or connect the following:
   
   Hub on the carrier and tighten the bolts to 52 ft. lbs. (70 Nm) No. 2 rear wheel bearing dust deflector using a screwdriver Rear axle into hub assembly No. 1 and 2 upper control arm assembly. Torque the new nut to the No. 2 rear upper control arm to 52 ft. lbs. (70 Nm). Temporarily tighten the No. 1 arm bolt. No. 1 and 2 rear suspension arm assembly. Temporarily tighten. Toe control link. Torque new nut to 52 ft. lbs. (70 Nm). Rear stabilizer link. Torque to 20 ft. lbs. (27 Nm). Parking brake assembly at the wheel hub Rear speed sensor Rear axle shaft nut. Torque to 214 ft. Lbs. (290 Nm) and stake the nut with a chisel and hammer. Rear brake disc and disc brake caliper
   
2. Adjust the parking brake.
3. Stabilize the suspension as follows :
   1. Install the wheel(s).
   2. Lower the vehicle and bounce it up and down several times to stabilize the rear suspension.
   3. Raise the vehicle.
   4. Remove the wheel.
   5. Jack up the rear lower suspension armplacing a wood block in between. Apply a load to the suspension so that the lower suspension arm is plkaced in a horizontal position.
   
   
4. Fully tighten the No. 1 rear upper control arm assembly to 119 ft. lbs. (161 Nm).
5. Fully tighten the No. 1 rear suspension arm assembly to 70 ft. lbs. (95 Nm).
6. Fully tighten the No. 2 rear suspension arm assembly to 119 ft. lbs. (161 Nm).
   
   Rear tire and wheel assembly
   

1. Before servicing the vehicle, refer to the Precautions section.
2. Raise and safely support the vehicle.
3. Remove or disconnect the following:
   NOTE If it is necessary to replace the hub or bearing, replace the components as an assembly.
   
   
   Rear tire and wheel assembly If equipped with rear disc brakes, the caliper mounting bolts. Leave the brake line connected and suspend the assembly out of the way. Brake rotor or drum 4 bolts and pull off the rear axle hub O-ring
   

To install:

1. Install or connect the following:
   
   Hub on the carrier and tighten the bolts to 59 ft. lbs. (80 Nm) Rotor or drum Caliper, f equipped with rear disc brakes and tighten the bolts to 34 ft. lbs. (64 Nm) Wheel
   

1. Before servicing the vehicle, refer to the Precautions section.
2. If equipped with air suspension, move the height control switch in the trunk area to the OFF position.
3. Remove or disconnect the following:
   
   Negative battery cable Rear wheel(s) Height control sensor link from the lower control arm Anti-lock Brake System (ABS) speed sensor and wiring harness Brake caliper bracket from the rear axle carrier by removing the 2 bolts. Support the caliper with a piece of wire. Brake rotor Parking brake shoes and cable Cotter pin, lock cap and the nut holding the halfshaft to the rear axle Suspension member brace by removing the 2 bolts Halfshaft bolts and washers Halfshaft from the vehicle Strut rod
   
4. Place matchmarks on the adjusting cam and body for the No. 1 control arm.
5. Remove or disconnect the following:
   
   Nut and adjusting cam Nut on the axle carrier side of the No. 1 lower control arm Separate the control arm from the axle carrier No. 1 lower control arm Stabilizer bar link from the No. 2 lower control arm.
   
6. Place matchmarks on the adjusting cam and body.
7. Remove or disconnect the following:
   
   Nut and adjusting cam from the No. 2 lower control arm Nut and bolt holding the No. 2 lower control arm to the axle carrier No. 2 control arm from the vehicle Nut and bolt on the lower side of the strut assembly 2 upper control arm set nuts and bolts Axle carrier with the upper control arm
   
8. Secure the axle carrier in a vise.
9. Remove or disconnect the following:
   
   Nut holding the upper control arm to the axle carrier and remove the control arm Dust deflector. Use a suitable prytool. Oil seal
   
   

   Fig. Removing the oil seal (inner)-LS 430
   
   

10. Remove the 2 bolts and nuts and shift the backing the plate towards the hub side (outside).
11. Remove or disconnect the following:
    
    Axle hub
    
    

    Fig. Removing the axle hub from the axle carrier-LS 430
    Backing plate. Inner race (outside) from the axle hub
    
    

    Fig. Removing the inner race (outside) from the axle hub-LS 430
    Oil seal (outer) from the axle
    
    

    Fig. Removing the oil seal (outer)-LS 430
    Snapring from inside the axle housing Bearing from the axle housing
    

To install:

1. Install or connect the following:
   
   New bearing to the axle housing Snapring to the axle carrier, using snapring pliers New outer oil seal. Coat the oil seal lip with multipurpose grease.
   
   

   Fig. Installing the oil seal (outer)-LS 430
   Backing plate to the axle housing. Do NOT install the bolts or nuts at this time. Inner race (inside) to the axle housing Axle hub to the axle housing Backing plate in position. Tighten the bolts and nuts to 43 ft. lbs. (59 Nm). New oil seal (inner) to the axle housing. Coat the oil seal lip with multipurpose grease.
   
   

   Fig. Installing the oil seal (inner)-LS 430
   New dust deflector. Be sure to align the hose for the ABS speed sensor in the dust deflector and axle carrier. Upper control arm to the axle carrier by installing the nut. Tighten the nut to 80 ft. lbs. (108 Nm). Axle carrier and upper control arm to the vehicle as an assembly 2 upper control arm set bolts and tighten the bolts to 121 ft. lbs. (164 Nm) Bolt and nut holding the strut to the axle carrier. Tighten to 101 ft. lbs. (137 Nm). Bolt and nut connecting the No. 2 lower control arm to the axle carrier. Tighten the bolt to 60 ft. lbs. (81 Nm). Nut and adjusting cam to hold the No. 2 lower control arm to the body. Align the adjusting cam marks and tighten the nut to 57 ft. lbs. (78 Nm). Stabilizer bar link to the No. 2 lower control arm and tighten the nut to 48 ft. lbs. (65 Nm) No. 1 lower control arm to the axle carrier and body. Install the nut to hold the No. 1 lower control arm to the axle carrier. Tighten the nut to 43 ft. lbs. (59 Nm). Nut and adjusting cam to hold the No. 1 lower control arm to the body. Align the matchmarks and tighten the nut to 57 ft. lbs. (78 Nm). Strut rod to the axle carrier and body. Install the bolt and nut to hold the strut rod to the body. Tighten to 57 ft. lbs. (78 Nm). Bolt and nut to hold the strut rod to the axle carrier. Tighten to 136 ft. lbs. (184 Nm) Parking brake shoes and cable Outboard joint side of the halfshaft and align the matchmarks on the side gear shaft and the halfshaft. Coat the threads with clean oil and install the hexagon bolts. Tighten bolts to 61 ft. lbs. (83 Nm). Suspension member brace with the 2 bolts. Tighten the 2 bolts to 37 ft. lbs. (50 Nm). Nut to hold the halfshaft to the rear axle. Tighten the nut to 213 ft. lbs. (289 Nm). Lock cap and cotter pin Brake disc to the axle hub with the matchmarks aligned. Install the 2 screws and tighten the screws to 48 inch lbs. (5 Nm). Brake caliper to the vehicle and install the 2 bolts. Tighten the bolts to 77 ft. lbs. (104 Nm). ABS speed sensor and wiring harness Height control sensor link with the matchmarks aligned. Tighten the nut to 48 inch lbs. (5 Nm). Rear wheel(s) Negative battery cable
   

2. Lower the vehicle and turn ON the air suspension switch.

Fig. Exploded view rear carrier assembly, hub and bearing-

1. Before servicing the vehicle, refer to the Precautions section.
2. Remove or disconnect the following:
   WARNING Be careful not to damage the boot and ABS sensor
   
   
   Rear wheel(s) Height control sensor link from the lower control arm Anti-lock Brake System (ABS) speed sensor and wiring harness Brake caliper bracket from the rear axle carrier by removing the 2 bolts. Support the caliper with a piece of wire. Brake rotor Parking brake shoes and cable Toe control link Separate upper control arm assembly Shock absorber from axle carrier Suspension arms No 1 and 2 from axle carrier Rear axle from carrier
   
   
   Wheel bearing dust deflector 4 bolts and axle & bearing hub assembly
   

To install:

1. Install or connect the following:
   
   4 bolts and axle & bearing assembly. Tighten to 48 ft. lbs (65 Nm) Rear wheel bearing dust deflector Rear drive axle Upper control arm. Temporarily tighten No 2 and No 1 suspension arms. Tighten to 52 ft. lbs. (70 Nm) Shock absorber. Temporarily tighten Toe control link. Tighten to 37 ft. lbs. (50 Nm) Fully tighten upper control arm. Tighten to 52 ft. lbs. (70 Nm) Height control sensor Parking brake shoes and cable Speed sensor Rear disc brake caliper Fully tighten shock with new nut to 52 ft. lbs. (70 Nm) Rear tire
   
2. Inspect and adjust rear wheel alignment
3. Check ABS speed sensor signal

1. Before servicing the vehicle, refer to the Precautions section.
2. Remove or disconnect the following:
   
   Rear wheel Wheel speed sensor Axle halfshaft Brake caliper and rotor Parking brake shoes Parking brake cable No. 1 lower suspension arm bolt No. 2 lower suspension arm bolt Toe control link Upper ball joint Axle carrier from the vehicle
   
3. Press the hub out of the wheel bearing, then remove the backing plate.
4. Remove the snapring, then press the wheel bearing out of the axle carrier.

To install:

NOTE Use a new toe control link nut for assembly.

1. Installation is the reverse of the removal procedure, while using the following torque values:
   
   Backing plate bolts: 43 ft. lbs. (59 Nm) No. 1 lower suspension arm bolt: 55 ft. lbs. (75 Nm) No. 2 lower suspension arm bolt: 81 ft. lbs. (110 Nm) Toe control link nut: 36 ft. lbs. (49 Nm) Upper ball joint nut: 80 ft. lbs. (108 Nm) Brake caliper support bolts: 77 ft. lbs. (104 Nm) Rear wheel lug nuts: 76 ft. lbs. (103 Nm)
   

Fig. Exploded view rear Axle carrier and hub assembly-ES 330

1. Before servicing the vehicle, refer to the Precautions section.
2. Remove or disconnect the following:
   
   Rear tire and wheel assembly Brake caliper support bracket Brake rotor Skid control sensor wire 4 bolts and rear hub and bearing assembly Skid control sensor
   

To install:

1. Install or connect the following:
   NOTE Inspect bearing back lash and hub deviation
   
   
   Skid control sensor Rear axle hub and bearing assembly with 4 bolts. Tighten to 59 ft. lbs. (80 Nm) Skid control sensor wire
   
   
   Rear disc Rear disc brake caliper assembly. Tighten to 46 ft. lbs (62 Nm) Flexible brake hose Rear tire and wheel
   
2. inspect and adjust rear wheel alignment
3. Check ABS speed sensor signal

Stabilizer Bar

Removal & Installation

1. Remove the rear wheels.
2. Remove the 2 nuts and left stabilizer bar link. If the ball joint turns together with the nut, use a hexagon wrench (5 mm) to hold the stud. Repeat for the right side.
3. Remove the 8 bolts, 2 No. 1 brackets and 2 bushings. Two types of bolts are used, so make sure the correct bolts are installed.
4. Remove the stabilizer bar.

To install:

1. Install the stabilizer bar.
2. Install the bushing and bracket with the 2 bolts and tighten to 14 ft. lbs. (19 Nm). Install the bushing to the inner side of the bushing stopper on the stabilizer bar.
3. Connect the stabilizer bar links and tighten the nuts to 29 ft. lbs. (39 Nm). Repeat for the right side.
4. Install the rear wheels.
5. Inspect and adjust rear wheel alignment.

Strut & Coil Spring

Removal & Installation

1. Before servicing the vehicle, refer to the Precautions section.
2. Remove or disconnect the following:
   CAUTION Do NOT remove the center nut to the strut at this time. The spring on the strut is under high pressure and can cause serious injury.
   
   
   No. 2 luggage compartment trim cover Left and right deck side trim box Rear luggage compartment trim cover Front luggage compartment trim cover Left and right side luggage compartment trim covers Rear wheel Rear wheel fender liner No. 2 differential support protector Rear suspension member brace Rear No. 2 lower control arm Mounting bolts and strut assembly
   
3. Secure the strut in a vise.
4. Compress the coil spring
5. Remove or disconnect the following:
   
   Upper strut retaining nut Suspension support Upper insulator Bumper Coil spring Insulator

use a large pry bar pry the inner tripod cv joint out of the transaxle differential gears.you have a retaining circlip that holds transaxle in place in the transaxle.besure to replace circlip and o ring seal on the transaxle stub shaft.torque strut assembly to steering knuckle attaching bolts.install the nuts to the attaching bolts and while holding bolt heads torque to 125 ft lbs and torque axle hub nut 125 ft lbs

raise you vehicle on jackstands. remove front wheel and tire.remove front caliper from steering knuckle assembly, remove rotor from hub by pulling it staright off. remove speed sensor bracket from strut assembly. remove hub and bearing to stub axle retaining nut. dislodge inner CV stub shaft retaining ringon transaxle assembly. insert small pry bar between transaxle case and inner CV joint by prying on it.remove strut assembly to steering knuckle bolts remove top of steering knuckle from strut assembly, then rotate CV assembly out of vehicle. Remove inner shaft from transaxle stub shaft grasp inner CV joint and interconnecting shaft and pull both pieces out at the same time. good luck!

Removal & Installation Independent Front Suspension – 2WD Vehicles To Remove:

1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
2. Safely raise and support the vehicle.
3. Support the lower control arm outboard end.
4. Remove or disconnect the following:
   • Upper shock absorber nut, retainer and grommet
   • Lower nuts and shock absorber

To Install:

1. Install or connect the following:
   • Lower retainer and grommet on the shock absorber stud and insert shock absorber through frame bracket hole
   • Lower nuts
     1. Torque to: 25 ft. lbs. (34 Nm)
   • Upper grommet, retainer and new nut (or existing nut with Mopar Lock N Seal or Loctiti 242) on the shock absorber stud
     1. Torque to: 40 ft. lbs. (54 Nm)
2. Remove support from lower control arm outboard end.
3. Lower the vehicle.

Independent Front Suspension – 4WD Vehicles To Remove:

1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
2. Safely raise and support the vehicle.
3. Remove tire and wheel assembly.
4. Support the lower control arm outboard end.
5. Remove or disconnect the following:
   
   
   • Upper shock nut with insulator and retainer
   • Lower shock bolt
   • Shock absorber

To Install:

1. Install or connect the following:
   • Upper part of shock absorber into frame bracket with insulators and retainers and nut
     1. Torque to: 40 ft. lbs. (54 Nm)
   • Lower part of shock absorber into lower control arm with the bolt
     1. Torque to: 100 ft. lbs. (135 Nm)
2. Remove support from lower control arm.
3. Install tire and wheel assembly.
4. Lower the vehicle.

Link/Coil Front Suspension To Remove:

1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
2. Remove or disconnect the following:
   • Nut, retainer, and grommet from upper stud in engine compartment
     
     
   • Nuts from upper shock bracket
3. Lower bolt from axle bracket and shock absorber from engine compartment

To Install:

1. Position lower retainer and grommet on upper stud and insert the shock through the spring from the engine compartment.
2. Install or connect the following:
   • Lower bolt
     1. Torque to: 100 ft. lbs. (135 Nm)
   • Upper shock bracket and nuts
     1. Torque to: 55 ft. lbs. (75 Nm)
   • Upper grommet, retainer and upper shock absorber nut
     1. Torque to: 35 ft. lbs. (47 Nm)

About an hour a side...This is the whole job and pictures....

The hub and wheel bearing unit is serviced as a complete assembly. Replacement of the front drive hub and bearing assembly can be done without having to remove the steering knuckle from the vehicle. However, if the hub/bearing assembly is frozen to the steering knuckle, removal of the steering knuckle is required.

1. Disconnect the negative battery cable.
   
2. Remove the cotter pin from the end of the stub axle. Remove the nut lock and spring washer. With the brakes applied, loosen, but do NOT remove the axle nut and washer with the vehicle still on the ground or damage to the wheel bearing will result.
   
3. Raise and safely support the vehicle. Remove the wheel.
   
4. Remove the front brake caliper assembly from the steering knuckle assembly and support from the strut assembly using a strong piece of wire.
   
1. Remove the front brake rotor from the hub/bearing assembly.
   
2. Remove the retaining nut and washer from the halfshaft stub axle.
   
3. Remove the ABS wheel speed sensor from the steering knuckle.
   
4. Remove the 4 hub and bearing assembly mounting bolts from behind the steering knuckle.
   
5. Remove the hub and bearing assembly from the steering knuckle.
   
5. To install:
   
   1. Thoroughly clean the mating surfaces of the steering knuckle and the hub and bearing assembly of any foreign material or nicks so the surfaces are clean and smooth.
      
   2. Install the new hub and bearing assembly and tighten the mounting bolts in a crisscross pattern to 45 ft. lbs. (65 Nm). Be sure the hub and bearing assembly is seated squarely against the front steering knuckle.
      
   3. Install the disc brake rotor.
      
   4. Install the brake caliper assembly onto the steering knuckle.
      
   5. Install the axle washer and nut. Tighten but do not torque.
      
   6. Install the ABS wheel speed sensor.
      
   7. Install the wheel and lug nuts. Torque the lug nuts, in sequence, to 95 ft. lbs. (129 Nm).
      
   8. Lower the vehicle. Do NOT roll the vehicle until the axle nut has been properly torqued or damage to the front wheel bearings will result.
      
   9. With the vehicle's brakes applied, torque the axle nut to 180 ft. lbs. (244 Nm). Install the spring washer, nut lock and a new cotter pin. Wrap the cotter pin prongs tightly around the axle nut lock.
      
   10. Reconnect the negative battery cable. Check the wheel alignment.
       

The hub/bearing assembly is attached to the steering knuckle with four bolts



Removing a hub/bearing assembly




If the hub/bearing is "frozen" to the steering knuckle, separate the ball joint and lightly tap on the hub/bearing from behind




The hub/bearing assembly should free itself from the steering knuckle

About $60 a hub.

raise rear of vechicle then support by jack stands.let rear suspension hang to take pressure off strut coil springs.remove rear package tray trim panel. remove rear wheel.remove brake load sensor .remove brake hose.remove stabilizer bar bracket and link.remove tension strut .remove spindle pinch bolt and strut assembly.if the strut coil spring broke you wont need a coil springcompressor.BESURE INSTALL NEW MOUNTING BOLTS AND PINCH BOLT.install the strut assembly.use a new pinch bolt .torque it to 50-67 ft lbs.torque the 3 upper mounting nuts to 19-25 ft lbs. tension strut torque nut to 35-46 ft lbs. stabilizer bar link torque to 60- 81 inch pounds.stabilizer bar bracket torque to 25-33 ft lbs.NOW INSTALL .brake hose / brake load sensor/ rear wheel /rear package tray trim panel.

Okay....here is the steps first....and then the directions on how to use the tools:

1. Raise and properly support the vehicle.
2. Remove the front wheel.
3. Detach the shock absorber lower mount by removing the two bolts.
4. Remove the retainer nut, retainer, cushion and shock absorber.
5. Detach the cushion retainer from the shock absorber.
6. Compress the coil spring with a commercially available spring compressor.
7. Detach the stabilizer bar.
8. Support the upper suspension arm and steering knuckle securely.
9. Remove the cotter pin.
10. Loosen and remove the nut.
11. Using a ball joint removal tool, detach the lower ball joint from the lower control arm.
12. Loosen the suspension arm set bolt.
13. Remove the suspension arm set bolt nut.
14. Remove the nut from the strut bar front set bolt.
15. Pull out both set bolts.
16. Remove the lower suspension arm and coil spring. To install:
    
17. Installation is the reverse of removal. Note the following torque specifications:
    1. Strut bar front set bolt: 221 ft. lbs. (300 Nm)
    2. Lower suspension arm set bolt: 148 ft. lbs. (200 Nm)
    3. Lower ball joint nut: 80 ft. lbs. (110 Nm)
    4. Lug nuts: 83 ft. lbs. (110 Nm).