Question about 1995 Mazda MX-6

1 Answer

I am replacing the cylinder head gasket on a MX6- 2.5 engine. I had to remove the camshafts to get to the cylinder head bolts. On the left side camshaft, there are marking on the gears so I know how to reinstall them. But on the right side there are no marks and I forgot to mark the gear. How do you know where to set the camshaft on the right side???

Posted by on

  • 2 more comments 
  • jdm0720 Apr 12, 2009

    I don't know the cc. and there is no engine code. the engine is all apart.

  • jdm0720 Apr 13, 2009

    Yes , its a v6, and its a 1995 Mazda LE , MX6.

  • steven martin
    steven martin May 11, 2010

    Ok, so its a V6 yes? and what year.

  • steven martin
    steven martin May 11, 2010

    What cc is the engine  and do you have an engine code?

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert
  • 117 Answers

This should help you.I am replacing the cylinder head gasket on a MX6- - ba22232.png

Posted on Apr 13, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need head bolt torque specs for a 2000 cadillac deville dts..


DeVille, Eldorado, Seville 1999-2005

Cylinder Head

Print


Removal & Installation

Left Side

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the cooling system.
  3. Properly relieve the fuel system pressure.
  4. Remove or disconnect the following:

    Negative battery cable Exhaust manifold Alternator Water crossover Intake manifold Valve cover Timing cover Secondary camshaft drive chain Power steering return hose retaining bolt from the cylinder head 3 M6 external drive bolts from the front portion of the cylinder head 10 M11 internal drive cylinder head bolts Cylinder head and gasket.
  5. Clean the head mating surfaces.

To install:

0996b43f80231662.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Left cylinder head bolt torque sequence-4.6L engine

  1. Install the cylinder head with a new gasket. Lubricate the bolts with engine oil prior to installation.
  2. Torque the M11 bolts in sequence as follows:
    1. Step 1: 30 ft. lbs. (40 Nm), plus an additional 70 degrees
    2. Step 2: Turn an additional 60 degrees
    3. Step 3: Turn an additional 60 degrees (total 190 degrees)

  3. Torque the M6 bolts to 106 inch lbs. (12 Nm)
  4. Install or connect the following:

    Power steering return hose retaining bolt to the cylinder head and tighten to 37 ft. lbs. (50 Nm) Secondary camshaft drive chain Timing cover Valve cover Intake manifold Water crossover Exhaust manifold Negative battery cable
  5. Change the oil and filter.
  6. Fill the cooling system.

Right Side
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the cooling system.
  3. Properly relieve the fuel system pressure.
  4. Remove or disconnect the following:

    Negative battery cable Exhaust manifold Water crossover Intake manifold Valve cover Timing cover Secondary camshaft drive chain Electrical connector from the Engine Coolant Temperature (ECT) sensor Nut attaching the coil cassette ground wire to the cylinder head Bolt attaching the exhaust crossover pipe to the cylinder head Bolt attaching the right transaxle mount bracket to the cylinder head Bolt attaching the rear transaxle brace to the transaxle Nuts attaching the rear transaxle brace to the cylinder head Rear transaxle brace 3 M6 external drive bolts from the front portion of the cylinder head 10 M11 internal drive cylinder head bolts Cylinder head and gasket
  5. Clean the head mating surfaces.

To install:

0996b43f80231663.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Right cylinder head bolt torque sequence- 4.6L engine

  1. Install the cylinder head with a new gasket. Lubricate the bolts with engine oil prior to installation.
  2. Torque the M11 bolts in sequence as follows:
    1. Step 1: 30 ft. lbs. (40 Nm), plus an additional 70 degrees.
    2. Step 2: Turn an additional 60 degrees.
    3. Step 3: Turn an additional 60 degrees (total 190 degrees).

  3. Torque the M6 bolts to 106 inch lbs. (12 Nm).
  4. Install or connect the following:

    Rear transaxle brace over the studs located at the rear of the right cylinder head Nuts attaching the rear transaxle brace to the cylinder head, loosely Bolts attaching the rear transaxle braces to the transaxle and tighten to 37 ft. lbs. (50 Nm) Nuts attaching the rear transaxle brace to the cylinder head and tighten 37 ft. lbs. (50 Nm) Electrical connector to the ECT sensor Bolt attaching the exhaust crossover pipe to the cylinder head and tighten to 18 ft. lbs. (25 Nm) Nut attaching the coil cassette ground wire to the cylinder head and tighten to 13 ft. lbs. (17 Nm) Secondary camshaft drive chain Timing cover Valve cover Intake manifold Water crossover Exhaust manifold Negative battery cable
  5. Change the oil and filter.
  6. Fill the cooling system.

Apr 16, 2013 | 2000 Cadillac DeVille DTS

1 Answer

How do i reset the timing on 2001 2.7l concorde if the chain was replaced and the timing is off


Did you take pictures while removing the originals? It's always a good habit. Below are the instructions you need to follow. Your own pics are very helpful when doing a big job like this.
  1. Disconnect negative battery (1) cable.
  2. Drain cooling system.
  3. Remove upper intake manifold.
  4. Remove cylinder head covers, crankshaft vibration damper, and timing chain cover.
CAUTION: When aligning timing marks, always rotate engine by turning the crankshaft. Failure to do so will result in valve and/or piston damage.
117014297

  1. Align crankshaft sprocket timing mark to mark on oil pump housing (2). The mark on oil pump housing is 600 ATDC of #1 cylinder.
CAUTION: When the timing chain is removed and the cylinder heads are still installed, DO NOT rotate the camshafts or crankshaft without first locating the proper crankshaft position. Failure to do so will result in valve and/or piston damage.
117016938

  1. Remove primary timing chain tensioner retainer cap (2) and tensioner (1) from right cylinder head.
117016939

  1. Disconnect and remove camshaft position sensor (4) from left cylinder head.
  2. Remove timing chain guide access plugs (3) from cylinder heads.
NOTE: When camshaft sprocket bolts are removed, the camshafts will rotate in a clockwise direction.
  1. Starting with the right camshaft sprocket, remove the sprocket attaching bolts. Remove camshaft damper (1) (if equipped) and sprocket.
  2. Remove left side camshaft sprocket attaching bolts and remove sprocket.
  3. Remove lower chain guide (7) and tensioner arm (8).
  4. Remove the primary timing chain (5).
  5. Remove crankshaft sprocket (6).
INSTALLATION
117016940

  1. Inspect all sprockets (4,9,11) and chain guides (2,5,10). Replace if worn.
  2. For crankshaft sprocket installation procedures Refer to CRANKSHAFT SPROCKET.
  3. If removed, install right and left side short chain guides (11). Tighten attaching bolts to 28 Nm (250 inch lbs.) .
  4. Align crankshaft sprocket timing mark to the mark on oil pump housing (3).
NOTE: Lubricate timing chain and guides with engine oil before installation.
  1. Place left side primary chain sprocket onto the chain so that the timing mark is located in-between the two (plated) timing links (1).
117016941

  1. Lower the primary chain with left side sprocket through the left cylinder head opening.
NOTE: The camshaft sprockets can be allowed to float on the camshaft hub during installation.
  1. Loosely position left side camshaft sprocket over camshaft hub.
  2. Align timing (plated) link to the crankshaft sprocket timing mark (3).
  3. Position primary chain onto water pump drive sprocket (10).
  4. Align right camshaft sprocket timing mark to the timing (plated) link on the timing chain (8) and loosely position over camshaft hub.
  5. Verify that all chain timing (plated) links are properly aligned to the timing marks on all sprockets.
  6. Install left side lower chain guide (2) and tensioner arm (5). Tighten attaching bolts to 28 Nm (250 inch lbs.) .
NOTE: Inspect O-ring on chain guide access plugs before installing. Replace O-ring as necessary.
  1. Install chain guide access plugs to cylinder heads. Tighten plugs to 20 Nm (15 ft. lbs.) .
NOTE: To reset the primary timing chain tensioner, engine oil will first need to be purged from the tensioner.
117016942

  1. Purge oil from timing chain tensioner using the following procedure:
    1. Place the check ball (2) end of tensioner into the shallow end of Special Tool 8186 (3).
    2. Using hand pressure, slowly depress tensioner until oil is purged from tensioner.
117016943

  1. Reset timing chain tensioner using the following procedure:
    1. Position cylinder plunger (4) into the deeper end of Special Tool 8186 (3).
    2. Apply a downward force until tensioner is reset.
NOTE: If oil was not first purged from the tensioner, use slight finger pressure to assist the center arm pin of Special Tool 8186 to unseat the tensioner's check ball.

CAUTION: Ensure the tensioner is properly reset. The tensioner body (4) must bottom against the top edge of Special Tool 8186 (3). Failure to properly perform the resetting procedure may cause tensioner jamming.

NOTE: Inspect the tensioner O-ring (2) for nicks or cuts and make sure the snap ring (1) is correctly installed, replace as necessary.
117016944

  1. Install the reset chain tensioner (1) into the right cylinder head.
  2. Position tensioner retaining plate (2) and tighten bolts (1) to 12 Nm (105 inch lbs.) .
117016945

  1. Starting at the right cylinder bank, first position the camshaft damper (1) (if equipped) on camshaft hub, then insert a 3/8 square drive extension with a breaker bar into intake camshaft drive hub. Rotate camshaft until the camshaft hub aligns to the camshaft sprocket and damper attaching holes. Install the sprocket attaching bolts and tighten to 28 Nm (250 inch lbs.) .
  2. Turn the left side camshaft by inserting a 3/8 square drive extension with a breaker bar into intake camshaft drive hub and rotate camshaft until the sprocket attaching bolts can be installed. Tighten sprocket bolts to 28 Nm (250 inch lbs.).
  3. Rotate engine slightly clockwise to remove timing chain slack, if necessary.
117016946

  1. Activate the timing chain tensioner by using a flat bladed pry tool to gently pry tensioner arm towards the tensioner slightly. Then release the tensioner arm. Verify the tensioner is activated (extends).
117016947

  1. Install camshaft position sensor (2) and connect electrical connector.
  2. Install the timing chain cover, crankshaft vibration damper, and cylinder head covers.
  3. Install upper intake manifold.
NOTE: After installation of a reset tensioner, engine noise will occur after initial start-up. This noise will normally disappear within 5-10 seconds.
  1. Fill cooling system.

Mar 27, 2013 | 2001 Chrysler Concorde

2 Answers

Need timing gear marks for 2004 Kia Sadona 3.5L engine



Removal & Installation

3.5L Engine

  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Record the radio anti theft code data.
  3. Remove or disconnect the following:

    Negative battery cable Engine cover Accessory drive belts Idler pulley Crankshaft pulley Power steering pump pulley Belt tensioner pulley Upper and lower timing belt covers
  4. Support the engine with a floor jack and remove the engine mount.
  5. Rotate the engine to align the camshaft sprocket timing marks with the cylinder head cover timing marks.

    0996b43f8022cb71.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Timing belt routing and timing marks-3.5L Engine

  6. Remove or disconnect the following:

    Auto tensioner Timing belt

    0996b43f8022cb72.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Timing belt and related components-3.5L Engine


To install:
  1. Ensure that the engine is set to Top Dead Center (TDC).
  2. Prepare the auto tensioner for installation by compressing it in a vise and installing a retaining pin.
  3. Install the timing belt in the following order:
    1. Crankshaft sprocket
    2. Idler pulley
    3. Left bank exhaust camshaft sprocket
    4. Left bank intake camshaft sprocket
    5. Water pump pulley
    6. Right bank intake camshaft sprocket
    7. Right bank exhaust camshaft sprocket
    8. Tensioner pulley

  4. Install the auto tensioner. Do not remove the retaining pin at this time.
  5. Check that the crankshaft and camshaft timing marks are aligned correctly.
  6. Rotate the crankshaft 1 / 4 turn Counterclockwise .
  7. Rotate the crankshaft 1 / 4 turn Clockwise to return the engine to TDC.
  8. Loosen the tensioner pulley center bolt.
  9. Apply 44 inch lbs. (5 Nm) torque to the tensioner pulley as shown and tighten the center bolt to 32-41 ft. lbs. (43-55 Nm).

    0996b43f8022cb73.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Adjusting the tensioner pulley-3.5L Engine

  10. Remove the auto tensioner retaining pin.
  11. Rotate the crankshaft 2 revolutions Clockwise , then wait 5 minutes for the auto tensioner to adjust.
  12. Measure the auto tensioner rod as shown. If the measurement is not 3.8-4.5 mm, then repeat the belt tensioning procedure.

    0996b43f8022cb74.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Measuring the auto tensioner rod-3.5L Engine

  13. When the auto tensioner measurement is correct, install or connect the following:

    Engine mount Upper and lower timing belt covers Belt tensioner pulley Power steering pump pulley Crankshaft pulley Idler pulley Accessory drive belts Engine cover Negative battery cable
  14. Reprogram the radio anti theft codes.

    Kia_Sedona_2002-2006
    Timing Chain, Sprockets, Front Cover & Seal

    Print


    Removal & Installation

    3.8L Engine

    1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
    2. Record the radio anti theft code data.
    3. Remove the engine from the vehicle.
    4. Remove the drive belt. Remove the power steering pump. Remove the air conditioning compressor.
    5. Remove the alternator. Remove the drive belt idler. Remove the drive belt tensioner. Remove the water pump pulley. Remove the intake manifold.
    6. Remove the connector bracket from the left cylinder head cover. Disconnect the right ignition coil connector, condenser connector and remove the bracket.
    7. Remove the left cylinder head cover retaining bolts. Remove the cylinder head cover from the engine.
    8. Remove the right cylinder head cover retaining bolts. Remove the cylinder head cover from the engine.
    9. Set the No. 1 cylinder to TDC on the compression stroke. Turn the crankshaft pulley and align its groove with the timing mark T of the lower timing chain cover.
    10. Check that the mark of the camshaft timing sprockets are in straight line positioning on the cylinder head surface. If not rotate the crankshaft 360 degrees. Do not rotate the engine counterclockwise.
    11. Remove the oil pan. Remove the crankshaft damper pulley. Remove the timing chain cover.
      NOTE Be careful not to damage the contact surfaces of the cylinder block, cylinder head and timing chain cover. Before removing the timing chain, mark the right and left timing chains with an identification mark based on the location of the sprocket because the identification mark on the chain for TDC can be erased.
    12. After compressing the timing chain tensioner, install a set pin. Remove the right cam to cam guide. Remove the right timing chain auto tensioner and timing chain tensioner arm.
    13. Remove the oil pump chain cover. Remove the oil pump chain tensioner assembly. Remove the oil pump chain guide. Remove the right timing chain.
    14. Remove the right timing chain guide. Remove the oil pump chain sprocket and oil pump chain. Remove the crankshaft sprocket, oil pump and camshaft drive gear.
    15. Remove the left cam to cam guide. Remove the left timing chain auto tensioner and timing chain tensioner arm. Remove the left timing chain.
    16. Remove the left timing chain guide. Remove the crankshaft sprocket and left camshaft drive. Remove the tensioner adapter assembly.

      0996b43f8020193b.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Timing chain and related components-3.8L Engine


    To install:
    1. Check the camshaft and crankshaft sprockets for wear and damage, replace as required.
    2. Inspect the tensioner arm and chain guide for wear and damage, replace as required.
    3. Check that the tensioner pin moves smoothly when the ratchet pawl is released with a thin rod.
    4. The key of the crankshaft should be aligned with the timing mark of the timing chain cover. This indicates that the piston is at TDC on the compression stroke.
    5. Install the tensioner adapter assembly. Install the crankshaft sprocket and left camshaft drive.
    6. Install the left timing chain guide and torque the retaining bolts 14-18 ft. lbs.
    7. Install the left timing chain. Be sure to install the chain with no slack between the camshaft and the crankshaft (crankshaft sprocket, timing chain guide, exhaust camshaft sprocket, intake camshaft sprocket). The timing mark of each sprocket should be matched with the timing mark (color ink) of the timing chain at installation of the timing chain.

      0996b43f80201924.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Left timing chain markings and installation: (D) exhaust camshaft sprocket (C) intake camshaft sprocket-3.8L Engine

    8. Install the left timing chain tensioner arm and torque the retaining bolts 14-16 ft. lbs.
    9. Install the left timing chain tensioner and torque the retaining bolts 7-9 ft. lbs.
    10. Install the left cam to cam guide and torque the retaining bolts 7-9 ft. lbs.
    11. Install the crankshaft sprocket, oil pump and right camshaft drive.
    12. Install the oil pump chain and oil pump sprocket. Torque the retaining bolt to 14-16 ft. lbs.
    13. Install the right timing chain guide. Torque the retaining bolts to 14-18 ft. lbs.
    14. Install the right timing chain. Be sure to install the chain with no slack between the camshaft and the crankshaft (crankshaft sprocket, intake camshaft sprocket, exhaust camshaft sprocket). The timing mark of each sprocket should be matched with the timing mark (color ink) of the timing chain at installation of the timing chain.

      0996b43f80201925.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Right timing chain markings and installation: (C) exhaust camshaft sprocket (B) intake camshaft sprocket-3.8L Engine

    15. Install the right timing chain tensioner arm. Torque the retaining bolts to 14-17 ft. lbs.
    16. Install the right timing chain auto tensioner. Torque the retaining bolts to 7-9 ft. lbs.
    17. Install the right cam to cam guide and torque the retaining bolts to 7-9 ft. lbs.
    18. Install the oil pump chain guide. Torque the retaining bolts to 7-9 ft. lbs.
    19. Install the oil pump tensioner assembly. Torque the retaining bolts to 7-9 ft. lbs.
    20. Pull out the pins on both the left and right hydraulic tensioners. Install the oil pump chain cover.
    21. Rotate the crankshaft two revolutions in the clockwise direction. Confirm the timing mark. Be sure to rotate the crankshaft in the clockwise direction.
    22. Apply sealant on the chain cover and on the cylinder head, cylinder block, and lower oil pan. Be sure these parts are free of engine oil and dirt.
      NOTE Before assembling the timing chain cover, the liquid sealant TB1217H should be applied on the gap between the cylinder head and block. The part must be assembled with five minutes after the sealant is applied.


      0996b43f80201926.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Sealant application (1 inch bead width)-3.8L Engine

    23. Apply sealant on the chain cover.
      NOTE The liquid sealant TB1217H should be applied on the gap between the cylinder head and block. The part must be assembled with five minutes after the sealant is applied.


      0996b43f80201927.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Timing cover sealant application-3.8L Engine

    24. Install a new gasket to the timing case cover.
      NOTE It is important that the dowel pins on the cylinder block and holes on the timing chain cover should be used as a reference in order to assemble the timing chain cover in the correct position.


      0996b43f80201928.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Timing cover gasket installation (A) gaskets-3.8L Engine

    25. Install the timing chain cover. Torque the retaining bolts in the proper sequence and to specification. The engine should not be started for at least thirty minutes after timing chain cover assembly.

      0996b43f80201929.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Timing cover bolt torque sequence and specification-3.8L Engine

    26. Install the timing case cover oil seal.
    27. Continue the installation in the reverse order of the removal procedure.

May 19, 2012 | 2004 Kia Sedona

1 Answer

Need to remove cilinderhead from a chevrolet trailblazer 2003


below are the instruction you well need to remove head .....good luck Removal Procedure
  1. Remove the air cleaner element.
  2. Remove the air cleaner outlet resonator. .
  3. Remove the powertrain control module (PCM) and engine wire harness bracket and related hoses and connections.
  4. Remove the generator.
  5. Remove the intake manifold.
  6. Remove the exhaust manifold. Do not remove the exhaust pipe from the manifold. Only have the manifold pushed off to the side of the engine.
  7. Position the A/C line out of the way towards the front of the vehicle.
  8. Disconnect the following cross-vehicle engine wiring harness connectors:
  9. • Engine coolant temperature sensor • Manifold absolute pressure (MAP) sensor • Ignition coils • Harness clamps at power steering pump • Wiring harness fastener at the right front inner fender • Throttle body • Camshaft sensors • Camshaft actuators • Fuel rail • Heated oxygen sensor (HO2S)
  10. Set aside the cross-vehicle engine wiring harness on the left side of the vehicle.
  11. Remove the camshaft cover.
  12. Partially drain the cooling system.

  13. Before performing one of the top dead center (TDC) procedures, break loose both the exhaust and intake camshaft sprocket bolts. Use a 25 mm (1 in) open end wrench on the camshaft hexes to hold the camshaft from turning. DO NOT remove the bolts.
  14. Perform one of the following methods for the service timing procedure.
  15. First Method--Rotate the engine clockwise by hand to TDC on the compression stroke by using a piston TDC indicator tool and/or dial indicator in the number 1 cylinder.
  16. First Method (continued)--The TDC indicator tool graduation marks on the shaft should note top of the piston stroke.
  17. First Method (continued)--When the piston is at TDC, the flats at the rear of the camshafts will be facing up and level when using a straight edge across the camshaft flats.
  18. Second Method--Rotate the crankshaft in the engine rotational direction clockwise until the number 1 piston is at TDC on the compression stroke. The word Delphi on the exhaust camshaft position actuator will be parallel with the cylinder head to cam cover mating surface. When the piston is at TDC, the flats at the rear of the camshafts will be facing up and level when using a straight edge across the camshaft flats. A 0.005 inch feeler gauge should not slide under the straight edge (1).
  19. Use a white paint pen or equivalent to place a reference mark on the harmonic balancer to the front cover for alignment purposes.
  20. Lower the vehicle.
  21. Important: If the timing is correct (TDC compression stroke number 1 cylinder), the camshaft flats will be in the up position.
    Install J 44221 to the back of the camshafts.
  22. Remove the upper timing chain guide to the cylinder head.
  23. Clean the timing chain and gears with brake cleaner or suitable solvent. Use a white paint pen or equivalent to place a reference mark on both timing gear sprockets and the timing chain to mark location prior to disassembly. It is recommended that the paint marks be in the 12 o'clock position.

  24. Install EN-48464 . It is important to install the tool with the proper orientation and to ensure that it is seated square against the timing chain and against the timing cover center bolt.


  25. The narrow ramp of the wedge tool needs to be placed so that it faces the timing chain.
  26. The wedge tool should be lightly seated using a couple of very light taps with a small plastic or brass hammer. The wedge tool will be fully seated against the tensioner after it moves about 25 mm (1 in).
  27. Once the tool is correctly installed, unscrew the handle and remove the handle

  28. Remove both upper cylinder head access hole plugs from the front of the cylinder head.
  29. Remove the 1 long and 2 short cylinder head bolts next to the exhaust and intake timing chain tensioner shoes and discard the bolts.
  30. Remove both upper timing chain tensioner shoe bolts.
  31. Remove the exhaust and the intake camshaft sprocket bolts. Discard the bolts.


  32. Carefully remove the exhaust and intake camshaft sprockets with the timing chain from the exhaust and intake camshafts. The illustration shows the exhaust camshaft sprocket already removed.


  33. Remove the sprockets from the chain, tie a piece of mechanic's wire on the timing chain and let it drop.


  34. Before removing the cylinder head bolts, use a drift punch and hammer to shock the bolts. This will ensure that the cylinder head bolts will not strip out the threads in the engine block or break. If a bolt breaks during engine disassembly, EN-47702 is available to assist in the removal of the remaining bolt segment.
  35. Remove the cylinder head bolts. Discard the bolts.
  36. Remove the cylinder head.
  37. Place the cylinder head on a flat, clean surface with the combustion chambers face up, in order to prevent damage to the deck face.
  38. Remove the cylinder head gasket.
  39. Discard the gasket.
  40. Remove all remaining gasket material from the engine block.
  41. Inspect the cylinder head gasket mating surface on the engine block.
  42. Clean and inspect the cylinder head.
  43. Disassemble the cylinder head if necessary.

May 23, 2011 | Chevrolet TrailBlazer Cars & Trucks

1 Answer

I need a print out of how i can change out a head gasket on a 1995 mercury cougar


Removal
  1. Drain engine cooling system.
  1. Disconnect battery ground cable (14301) .
  1. Remove engine air cleaner (ACL) (9600) including air cleaner outlet tube (9B659) .
  1. Loosen drive belt tensioner (6B209). Remove drive belts (8620) .
  1. If LH cylinder head (6049) is being removed, perform the following:
    1. Remove oil filler cap (6766) .
    1. Remove power steering pump front mounting bracket retaining bolts.
    1. Remove generator (GEN) (10346) and belt idler pulley (8678).
    1. Remove power steering pump/generator bracket retaining bolts. Leave hoses connected, place pump/bracket assembly aside in a position to prevent fluid from leaking out.
  1. If RH cylinder head is being removed, perform the following:
    1. Remove drive belts .
    1. If equipped with A/C, remove mounting bracket retaining bolts. Leave hoses connected and position A/C compressor (19703) aside.
    1. Remove positive crankcase ventilation valve (PCV valve) (6A666) .
  1. Remove upper intake manifold (9424) .
  1. Remove valve cover retaining bolts.
  1. Remove fuel injection supply manifold (9F792).
  1. Remove lower intake manifold as outlined.
  1. Remove exhaust manifolds (9430) as outlined.
  1. Loosen rocker arm seat retaining bolts enough to allow rocker arm (6564) to be lifted off the push rod (6565) and rotate to one side.
  1. Remove push rods . Identify position of each push rod . Push rods should be installed in their original position during assembly.
  1. Remove cylinder head retaining bolts and discard.
  1. Remove cylinder heads .
  1. Remove and discard old head gaskets (6051) .
Installation
  1. NOTE: Lightly oil all bolts and stud bolt threads before installation except those specifying special sealant.
    Clean cylinder head, intake manifold , valve cover (6582) and head gasket surfaces. If cylinder head was removed for head gasket replacement, check flatness and sealing areas for scratches of cylinder head and cylinder block gasket surfaces. Refer to Section 03-00 for procedure.
  2. Position new head gaskets onto cylinder block (6010) using cylinder head to block dowels (6A008) for alignment.

    Head Gasket


    a11431c.gif

  3. Position cylinder heads onto cylinder block .
  4. ani_caut.gif CAUTION: Always use new cylinder head bolts to ensure a leak-tight assembly. Torque retention with used bolts can vary, which may result in coolant or compression leakage at the cylinder head mating surface area.
    -ft).
  5. For 3.8L non-SC engine, tighten cylinder head retaining bolts in numerical sequence in three steps as follows:
    1. 20 Nm (15 Lb-Ft)
    1. 40 Nm (29 Lb-Ft)
    1. 50 Nm (37 Lb-Ft)
  6. ani_caut.gif CAUTION: Do not loosen all of the bolts at the same time, only work on one bolt at a time or possible damage to engine or leakage may occur.
    In sequence, loosen retaining bolts two to three revolutions and retighten bolts one at a time in the following manner:
    1. Long bolts:
      • 15-25 Nm (11-18 lb-ft).
      • Tighten bolt an additional 85-95 degrees.
      • Go to next bolt in sequence.
    1. Short bolts:
      • 10-20 Nm (7-15 lb-ft).
      • Tighten bolt an additional 85-95 degrees.
      • Go to next bolt in sequence.


      a11399c.gif


      Item Part Number Description 1 6010 Cylinder Block 2 - Locating Pin (2 Req'd) 3 N802515-S Cylinder Head Bolt (4 Req'd Each Side) 4 6049 Cylinder Head 5 N802516-S Cylinder Head Bolt (4 Req'd Each Side) 6 6A008 Cylinder Head to Block Dowel
  7. NOTE: If original valve train components are being installed, a valve clearance check is not required. If a component has been replaced, perform a valve clearance check as outlined.
    Dip each push rod end in Engine Assembly Lubricant D9AZ-19579-D or equivalent meeting Ford Specification ESR-M99C80-A and install push rods in their original position.
  8. For each valve, rotate crankshaft (6303) until valve tappet (6500) rests on the heel (base circle) of the camshaft lobe, before tightening rocker arm seat retaining bolts to 7-15 Nm (5-11 lb-ft) maximum.
  9. Lubricate all rocker arms with Engine Assembly Lubricant D9AZ-19579-D or equivalent meeting Ford Specification ESR-M99C80-A. Final-tighten the rocker arm seat bolts to 30-40 Nm (22-30 lb-ft). For final tightening, camshaft (6250) may be in any position.
  10. Install exhaust manifolds as outlined.
  11. Install lower intake manifold as outlined.
  12. Install fuel injection supply manifold .
  13. Position valve cover and new valve cover gasket (6584) on cylinder head and install retaining bolts. Note location of ignition wire routing clip stud bolts. Tighten retaining bolts to 9-12 Nm (7-9 lb-ft).
  14. Install upper intake manifold .Install spark plugs (12405) , if removed.
  15. Connect ignition wires to the spark plugs .
  16. If LH cylinder head is being installed, perform the following:
    1. Install oil filler cap.
    1. Install generator/power steering pump mounting bracket.
    1. Install generator .
    1. Install main accessory drive belt tensioner .
    1. Install power steering pump (3A674) .
    1. Install power steering pump support bracket.If RH cylinder head is being installed, perform the following:
    1. Install positive crankcase ventilation valve .
    1. If equipped with A/C, install A/C compressor mounting brackets (2882) and A/C compressor .
  17. Install drive belt and tighten to specification.
  18. Connect battery ground cable .
  19. Install air cleaner outlet tube.
2010&c18=modelyear&c35=wsm%2ccylinder%20heads%2cssd%2c03-01a%2cin-vehicle%20service&s=1249x702&c=32&j=1.3&v=y&k=y&bw=910&bh=359&ct=lan&hp=n&[aqe]

Mar 06, 2011 | Mercury Cougar Cars & Trucks

1 Answer

Hi can you tell me how much torque spectification to replace head gasket bolts, camshaft caps bolts, and camshaft pully bolts for 1994 GS 300 lexus Thank you very much for your help



  1. 60293.gif

    Cylinder head bolt tightening sequence - 1993-97

  2. Remove the head from the engine. If prying is necessary, use a protected blade; take great care not to damage the mating surfaces of the head and block.

  3. Clean the head and block of all gasket material. Take great care not to gouge or scratch the mating surfaces.

To install:

  1. Place a new gasket on the cylinder block. Make sure it is positioned correctly. Install the cylinder head in position.

  2. Lightly coat the head bolt threads and plate washers with engine oil. Install the bolts in the head.

  3. Uniformly tighten the head bolts in several passes in sequence, to 25 ft. lbs. (34 Nm).

  4. Mark the front of each bolt with a dot of paint. Following the correct order, tighten each bolt an additional 90 degrees. When complete, all the paint marks should face to the side of the engine.

  5. Again following the correct order, tighten the bolts another 90 degrees of rotation. When complete, the paint marks should face the rear of the engine, exactly 180 degrees away from the original starting point. Correct bolt torque is expressed as 25 ft. lbs. (34 Nm) + 90° + 90°.


Jan 07, 2011 | 1994 Lexus GS 300

1 Answer

Cylinder head removal on 2005 nissan altima 2.5 engine would like to know how to remove the camshaft to remove the head bolts


CYLINDER HEAD REMOVAL

2.5L Engines
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain cooling system and engine oil.
  3. Relieve the fuel system pressure.
  4. Remove or disconnect the following:
    • Negative battery cable
    • Upper radiator hose and heater hose
    • Right side fuse/relay box and move aside
    • Engine undercover
    • Resonator and air cleaner case
    • Engine top cover
    • All electrical and vacuum lines at the head
    • Fuse hose quick connector at fuel tube side
    • Engine harness and power steering hose bracket
    • Timing chain
    • Drive belt tensioner
    • Camshafts
    • Spark plugs
    • Exhaust manifold
  5. Support the engine from above and below with a suitable jack and hoist.
  6. Remove or disconnect the following:
    • Power steering pump and reservoir and wire aside
    • Auxiliary drive belts
    • A/C compressor and wire aside
    • Upper sway bar links
    • Front and rear engine mount through bolts
    • Lower ball joints
    • 2 steering gear housing mounting bolts
    • Front suspension member bolts and front suspension member
  7. Loosen the cylinder head bolts in the sequence shown and remove the cylinder head.
d365038.gif
Removing the front suspension member—Altima

7555308.gif
Cylinder head bolt removal sequence—2.5L engine–Altima and Sentra

1e6ce81.gif
Cylinder head bolt tightening sequence—2.5L engine–Altima and Sentra

To install:
  1. Clean the gasket surfaces.
  2. Using new head gaskets, install the cylinder heads.
    NOTE If possible, replacement of the head bolts is suggested.

  3. If replacement of the head bolts is not possible, perform the following bolt measurement:
    • Measure the diameter of the head bolt 0.43 in. (11mm) from the bottom of the bolt.
    • Measure the diameter of the head bolt 2.17 in. (55mm) from the bottom of the bolt.
    • Whenever the size difference between the 2 measurements exceeds 0.0091 in. (0.23mm) the head bolts must be replaced.
  4. Apply clean engine oil to the bolt threads and seating surfaces and tighten the cylinder head bolts in sequence as follows:
    • Step 1: 72 ft. lbs. (98 Nm).
    • Step 2: Loosen all the bolts completely.
    • Step 2: 29 ft. lbs. (33 Nm).
    • Step 4: Plus 75–80 degrees clockwise.
    • Step 5: Plus 75–80 degrees clockwise.
  5. Install the front suspension member and tighten the bolts to the specifications shown in the illustration.
  6. Install or connect the following:
    • 2 steering gear housing mounting bolts
    • Lower ball joints
    • Front and rear engine mount through bolts
    • Upper sway bar links
    • A/C compressor
    • Auxiliary drive belts
    • Power steering pump and reservoir
    • Exhaust manifold
    • Spark plugs
    • Camshafts
    • Drive belt tensioner
    • Timing chain
    • Engine harness and power steering hose bracket
    • Fuse hose quick connector at fuel tube side
    • All electrical and vacuum lines at the head
    • Engine top cover
    • Resonator and air cleaner case
    • Engine undercover
    • Right side fuse/relay box and move aside
    • Upper radiator hose and heater hose
    • Negative battery cable
  7. Fill the cooling system and engine oil
  8. Start the vehicle, check for leaks and repair if necessary.

Nov 13, 2009 | 2005 Nissan Altima

1 Answer

How to change head gasket?on gas v6. ISUZU RODEO Vin #452CG58V554341786


This is the same for many years. I will send this in 2 post it is to long. Hope this helps you. From the '00 Rodeo workshop manual:

Cylinder Head Assembly
Removal
1. Disconnect battery ground cable.
2. Disconnect connector of intake air temperature
sensor from intake air duct.
3. Remove PCV hose from air intake duct.
4. Remove nut from air intake duct bracket and loosen
hose clamp on throttle body. Remove air intake duct
assembly with air cleaner cover.
5. Remove intake air duct bracket from cylinder head.
6. Drain engine coolant.
7. Move drive belt tensioner to loose side using wrench
then remove drive belt.
033RW001
8. Remove radiator upper hose from engine side.
9. Remove four nuts of exhaust front pipe.
10. Remove three bolts from generator bracket then
remove the generator with brackets.
065RW025
11. Disconnect crankshaft angle sensor connector.
12. Disconnect knock sensor connector.
13. Remove heater hose from adapter side.
14. Remove heater hose from water pipe side.
15. Remove water hose between water pipe and throttle
body.
16. Remove fuel pipe joint eye bolts from fuel rail
assembly and remove fuel pipe bracket with electric
ground cable.
042RW001
17. Disconnect connector for evaporation valve.
18. Remove canister hose.
19. Remove fixing nut of intake manifold stay from
cylinder block side.
025RW002
20. Remove two bolts from intake manifold for water pipe
support and remove cylinder head assembly.
21. Remove engine harness cover and disconnect three
connectors from chassis harness on left rear side
engine compartment.
22. Disconnect connector for power steering pump
pressure switch.
23. Remove four bolts and remove crankshaft pulley.
ENGINE MECHANICAL (X22SE 2.2L) 6A–23
020RW014
24. Remove two bolts and nut then remove timing belt
front cover.
25. Remove ventilation hose from cylinder block side and
from cylinder head side.
26. Remove two bolts, ignition cable cover and remove
ignition cables from spark plug.
27. Disconnect camshaft angle sensor connector.
28. Remove ten bolts and remove cylinder head cover.
29. Remove fixing bolt of timing belt tensioner then
remove timing belt tensioner.
020RW010
30. Remove timing belt.
CAUTION:
 Do not bend or twist belt, otherwise its core could
be damaged. The belt should not be bent at a
radius less than 30 mm.
 Timing belt drive gear counterhold with J–42620.
 Do not allow oil or other chemical substances to
come in contact with the belt. They will shorten
the life.
 Do not attempt to pry or stretch the belt with a
screw driver or any other tool during installation.
 Store timing belt in cool and dark place. Never
expose the belt direct sunlight or heat.
31. Remove two idle pulleys, the left side with idle pulley
bracket.
32. Remove two bolts and stud bolt and remove timing
belt rear cover.
33. Remove camshaft angle sensor
34. Disconnect engine oil pressure switch connector.
050RW005
35. Remove camshaft assembly exhaust side.
36. Use J–42623 to remove ten cylinder head fixing bolts
012RW007
6A–24 ENGINE MECHANICAL (X22SE 2.2L)
Installation
1. Put cylinder head gasket on the cylinder block.
012RW011
2. Install the cylinder head assembly, tighten cylinder
head bolts by four steps tightening method in the
following sequence to the specified torque.(use
J–42623)
Torque: 25 N·m (18 lb ft) + 90 + 90 + 90
012RW006
3. Install camshaft assembly exhaust side and tighten
camshaft bracket bolts in the sequence to the
specified torque.
Torque: 8 N·m (5.9 lb ft)
015RW014
4. Connect engine oil pressure switch connector.
5. Install camshaft angle sensor.
6. Install the timing belt rear cover and tighten three
bolts to the specified torque.
Torque
M6 bolt: 6 N·m (4.4 lb ft)
M8 bolt: 8 N·m (5.8 lb ft)
020RW012
7. Install left side idle pulley with idle pulley bracket,
tighten to the specified torque and install right side
idle pulley and tighten to the specified torque.
Torque: 25 N·m (18 lb ft)
ENGINE MECHANICAL (X22SE 2.2L) 6A–25
020RW016

Oct 09, 2009 | Isuzu Rodeo Cars & Trucks

Not finding what you are looking for?
1995 Mazda MX-6 Logo

Related Topics:

372 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...