Question about 1993 Chevrolet S-10 Blazer

2 Answers

Trying to get error codes

How do i trip the wires to ge fix codes

Posted by on

  • Leonard Huggins
    Leonard Huggins Apr 12, 2009

    ok but what wires do i cross under the dash to get the codes

×

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 43 Answers

This is an OBD1 module located under the dash:
1st turn off the ignition.
2. Use a jumper wire between the ground terminal "A" top right and the diagnostic terminal "B" second from top right.
3. Turn the ignition to on but DO NOT START ENGINE.
The "Service engine light" soon will flash the code 12 - one flash followed by 2 short flashes. it will repeat then pause followed by yuor trouble codes flash.
Hope this helps

Posted on Apr 12, 2009

  • Blake Whitley Apr 12, 2009

    you don't cross any wires. there is a rectangular plug BLACK mounted at the bottom edge under the dash around your left knee. this a mounted plug that is open it looks like it is ready to receive a male plug. this is the OBD1 . & has 12 slots but only 7 are wired (5 are missing terminals inside the plug) you need to get a small length of solid wire (paper clip works) and jumper it between position A & B. the plug terminals are as shown:



    F E -C B A

    |OOOO ■■|

    |OOOOOO|

    G H - - - -

  • Blake Whitley Apr 12, 2009

    Rember if you disconnect the battery you loose all your codes!

    get your codes 1st. they will be in type of morris code on the dash in a series of blinks of the service engine soon light. Count the blinks. a long pause will seperate multiple codes. the codes will start and end with the code 12 flashed as noted above. .

×

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

First you need to unplug the battery cable from the battery post.for 1 min .to delete the error codes
TRY IT..

Posted on Apr 12, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Getting error code U0414 P0118,P2060F what does that mean and what parts do I need to change for my ford escape 2008


With all these codes you need a professional to help fix this, you will likely throw parts at it and still not fix it. If you do want to try a repair at very least go on eBay and try and find a used factory repair manual set. If you google each code the explanation of the code will show, but it will only give you a system of the car, that means it can be a sensor or a part or the wiring or the computer that runs the system. Good luck

Jun 25, 2016 | 2008 Ford Escape

1 Answer

L had an accident with my Chevy equinx 2007 and it was working when i gave it out for panel beating, after the radiator was fixed , the vehicle refuse to start again, a computer error detector said i


Some cars have a sensor that turns off power to the fuel pump in an accident. It's possible that this was tripped while body work being done. Could also be a broken wire

Mar 14, 2014 | 2007 Chevrolet Equinox LS New Cars

1 Answer

Ecm bcm error code f32 was on smelled something burning now its not coming on and car has been stalling


You may have more than one problem.
The code F32 is for a problem between the engine computer and the body computer, or a loss of memory. To fix that someone would need to check the ground connections and the harness between the two computers.
The engine could be burning coolant like the head gasket problem you mentioned.

Dec 13, 2012 | 1993 Cadillac DeVille

1 Answer

I need to know what the code for a 1993 honda accord it flashed 4 slow then three short fast flashes, my car has been lagging really bad and i dont know exactly what i need to do to fix it i was told it is...


Found this for you on the web. Good luck.

c/p;

What is code 43?

Code 43 is "fuel supply system."

This code will trip when the ECU and the readings from the o2 sensor don't get along(in layman's term or easy enough for Si Speed to understand biggrin.gif) read the above two threads).

How to diagnose and fix?

First things first, when was the last time you changed your O2 sensor? Start by replacing that first because most likely, that's the main culprit. Now, you may wonder why doesn't the CEL indicate code 41(heated o2 sensor)? Usually when the o2 sensor is completely dead, that code will trip. Also, even though the o2 sensor is working, the voltage or ground isn't 100% Because of that, it will correlate with code 43.

If replacing the o2 sensor did not help code 43 to disappear, next thing is to replace your fuel filter. A clogged fuel filter will also trip code 43.

Next up, did you install an aftermarket Fuel Pressure Regulator? I have a few friends with 3rd gen Preludes and both of them installed aftermarket FPR's and they too, trip code 43. Him and a lot of people who install aftermarket FPR's mess with the PSI and that will cause code 43 to appear(on a stock ECU mind you). Bring it back to stock PSI to help fight code 43.

Those are the 3 main culprits that will cause code 43 from my experiences. Injectors, spark plugs & wires, most likely anything "fuel' related that isn't working properly will also cause code 43.

May 03, 2011 | 1993 Honda Accord

1 Answer

2002 Grand Cherokee P0601 Error


P0601 is an internal PCM failure. It is not passing one of it's self-tests and the code sets. The only fix for this code is to replace the PCM.

Jun 15, 2009 | 2002 Jeep Grand Cherokee

1 Answer

Looses Power when on long trip pulling camper or trailer flagging oxygen Sensors error


Sounds like a fuel problem. Change the filter and have the fuel pressure checked. A fuel problem can cause an O2 code.

May 19, 2009 | 1999 GMC Suburban

1 Answer

Speedometer


Aha! Found a fix, at least to my problem.

Try pressing the trip odometer reset button for 5 seconds. It will flash an error code. Then the odometer lights will flash, a bunch of error codes flash. Let it finish (my problem was that I tried to start the car the first time before it finished).

Aug 23, 2008 | 2001 Chrysler Town & Country

Not finding what you are looking for?
1993 Chevrolet S-10 Blazer Logo

225 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...