Question about Oldsmobile Alero

1 Answer

I Pulled my tie rod end off and removed the boot and now i can't get the rod out. Is there a special tool i need to remove it?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 4 Answers

Most likely not you need to get a fork bar put it between the 2 peaces and separate them it take alot of presher but it will give

Posted on Apr 12, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have anyone out there ever change inner tie rods on a1995 honda odyssey?,if so simply explain,THANKS


Procedure on replacing the inner tie rod ends:


1) Raise and safely support the vehicle.

2) Remove the front wheel/tire assembly.

3) Clean the steering rod between the steering boot and outer tie rod end lock nut with a suitable penetrating lubricant and a clean cloth or shop towel.

4) Loosen the outer tie rod end locking nut 1/8 turn.

5) Loosen the steering boot clamp(s), and slide the small clamp off the boot.

6) Carefully loosen the boot and slide outward off the steering rack and onto the shaft to expose the inner steering rod mounting fastener.

7) If necessary, position the inner steering rack shaft in or out to allow for additional access.

8) Relieve the steering rod nut locking tab from the inner steering rack shaft, then loosen the steering rod ball socket nut 1 turn.

9) Matchmark the tie rod end to the threaded shaft.

10) Remove the cotter key and castle nut from the outer tie rod end threaded spindle, and using a tie rod end removal tool, remove the tie rod from the steering knuckle.

11) Hold the tie rod with a wrench, and remove the outer tie rod end from the threaded rod, counting the number of complete turns it takes to remove the tie rod end from the shaft. Write the number of turns on a piece of note paper.

12) Remove the tie rod end lock nut from the threaded steering shaft.

13) Slide the steering rack boot off the shaft.

14) Remove the inner steering rod ball socket nut from the inner steering rack shaft.

To install:

1) Inspect the tie rod end for looseness, and the steering rack boot and tie rod end boot for cracks deterioration or damage and replace as necessary.

2) Clean steering rack shaft and apply a light coating of Genuine Honda Power steering fluid as necessary.

3) Apply a medium strength locking agent to the threads where the inner steering rod ball socket mounts. Use a new locking washer and a new stop washer, and install the inner tie rod onto the steering rack shaft.

4) Tighten the inner tie rod end fastener by 58 ft. lbs. (78 Nm)

5) Peen the lock washer over the nut or onto the flat surface of the steering rack shaft.

6) Apply silicone grease to the outer circumference of the inner tie rod end ball socket, and onto the groove just outside of the socket.

7) Apply silicone grease to the inside of the small end of the steering rack boot, and slide the boot over the steering shaft and onto the rack and install the boot clamps. If the boot has air hose fittings make sure they are installed as removed.

8) Apply a light film of an anti-seize compound onto the threaded tie rod end, and install the tie rod end lock nut.

9) Install the tie rod end onto the tie rod, turning it in exactly the number of turns it took to remove it.

10) Install the tie rod end following the tie rod end installation procedure.

11) The balance of installation is the reverse of the removal procedure.

12) Check the front end alignment and adjust as necessary.

Sep 10, 2012 | 1995 Honda Odyssey

1 Answer

How to replace tie tods on a 2001 and should both tie rods have a grese fighting or just one. and how to get the bands off to remove the boot .


ok, Tie rods don't have boots. The only thing up front with a boot is the CV joint. You have to use a cutter to remove the bands from a CV joint however, unless your trying to repair the joint you don't want to do that. There is no lubrication point inside the boot you need to reach. If for some reason you need to remove that boot you need to get a CV joint Boot Repair kit to do this as it will have replacement bands to use in the repair. Because of the nature of a CV joint and it's importance to operating correctly I don't recommend trying to do a Joint repair on your own. On the Tie Rod typically you will replace the out end. You need to have a tie Rod puller to remove the tie rod end off the "A" frame after you have released the lock nut in the center then simply unscrew the tie rod end. You'll want to make sure you mark the old tie rod somehow so you can put beside the new part and mark it so you know how far to screw that in so the Alignment matches, as close as possible. The tie rod puller is a special tool you can get from Auto Zone to remove the Tie rod end from the "A" frame.

Oct 27, 2010 | 2002 Chrysler PT Cruiser

1 Answer

Need to know the size of the socket needed to remove the front hubs on a dodge ram 3500 1 ton 4 x 4 with cummins engine?


Removing Tie Rod End Attaching Nut Nut is to be removed from tie rod end using the following procedure, hold tie rod end stud with a 11/32 socket while loosening and removing nut with wrench Removing Tie Rod End Attaching Nut
Remove the tie rod end from steering knuckle arm, using Remover, Special Tool MB-991113 Tie Rod End Removal From Steering Knuckle .
Remove the upper ball joint stud from the steering knuckle using Puller, Special Tool, C3894-A Ball Joint Stud .----------------------- The procedure is :-- Do NOT pound on the outside of the hub. First you will need a 5 inch long half inch drive socket extension. Start the 4 hub bolts about half way, then witha helper hold the extension between one of the 4 bolts and the axle housing then have the helper turn the steering wheel to push on the bolt and hub. If it is really rusted in you might have to start the truck to get more pressure on it while turning. Thanks. Keep updated for any more query. You can rate this solution and show your appreciation.

Jul 11, 2010 | 1997 Pontiac Grand Am

2 Answers

One of the steering rods that goes from the rack to the right tie rod is bent. Can I replace the rod or must I replace the entire rack?


you can replace just the tie rod yourself although you do need a special tool but you should be able to get it at any parts store just take the outer tie rod loose from the steering knuckle remove the rubber boot from the inner tie rod and get the proper size tool to fit he nut and remove and replace the inner tie rod and install in reverse order make sure to count the amout of turns that removed the outer tie rod and reinstall the same amount of turns then afterward the car needs to be aligned

Apr 13, 2010 | 2000 Ford Focus

1 Answer

How to replace to inner tie rod


remove tire un bolt outter tie rod end from spindle where it connects loosen the jam nut remove tie rod end count how many turns it takes to get off or your alignment will be way off remove clamps off of the rubber boot one small one large there is a special tool to remove the inner tie rod but you might be able to get a pair of pliers on it turn it out when you replace the end make sure to fold the washer over the flat spots on the tie rod to ensure it wont work loose not to hard of a job

Feb 25, 2010 | 1998 Mercury Sable

4 Answers

How do I replace the upper ball joints in my 2002 Ford Explorer?


The upper ball joints are replaceable without replacing the control arms. Use Moog K80008 ball joints and a ball joint press.

Jun 25, 2009 | 2002 Ford Explorer

2 Answers

How do I install driver side inner tie rod on my 1997 chevy cavalier?No room to work. Do I need to remove whole rack and pinion assembly?


you don't need to remove the whole rack but do need a special tool called inner tie rod tool. can be bought or borrowed form most auto parts stores. first remove wheel. next loosen the jam nut on inner tie rod at the end of outer tie rod. remove cotter pin and nut on outer. use seperator or pickle fork to seperate outer from knuckle. then remove the clamps on boot and remove. then take tie rod tool and find the right size end and turn with 1/2" ratchet or breaker bar. it will turn hard at first cause of it being staked on to the threads. when it is off install new part with loc-tite on threads and tighten. when tight crimp inner flanges with either plier or hammer and punch to the rack. install in reverse order. remember to measure distance from clamp on outer side of boot to jam nut so you can get the alignment close until you get to shop for alignment.

May 05, 2009 | 1997 Chevrolet Cavalier

2 Answers

Tie rod problem 98 Dodge


There is a tool that you can use that will make it easier for you. To get to the tie rod end, remove the wheel and take the outer tie rod end loose from the hub. You will have to use a hammer and hit the socket where the end goes into the hub to free it up. Once you have the tie rod loose from the hub, loosen the nut behind the outer tie rod end. Count the revolutions as you unscrew the outer end off and write te number down so you will know how far to put it back on. This will save your alignment. Now, the end that is still there is your inner tie rod end. You will have to undo the bellows boot to get to the nut. The tool will slide over the end and secure onto the nut. Now you just unscrew this and replace with you new inner tie rod end.
Please remember to rate this fix.

Feb 16, 2009 | 1998 Dodge Grand Caravan

1 Answer

Stablizer sway bar link


Remove the front wheel. Loosen the jam nut on the tie rod using pliers and wrench with lots of Liquid Wrench or other penetration oil. Back off the jam nut and mark the position of the tie rod end on the tie rod threads with paint.
Remove the cotter pin from the ballstud and then loosen the nut. Again more Liquid Wrench may be helpful. Now place the puller (special tool from auto parts store or Sears Craftsman) over the steering knuckle and separate the tie rod end from the knuckle. Fully remove the nut and then turn the tie rod end off the tie rod.
Installation is just the reverse with the new tie rod end turned on the tie rod up to the paint mark. Tighten the jam nut up to the tie rod end. Secure the tie rod end to the steering knuckle with the nut with a torque of 35 to 46 ft-lbs and insert a new cotter pin. Don't forget to reinstall the front wheel. Checking the front end alignment is recommended. Do not get the more expensive four wheel alignment as they cannot make any adjustment to align the rear wheels. ps Buy at least the Haynes Repair Manual for your car or splurge and buy the Ford complete repair manual.

Oct 03, 2008 | 1996 Ford Taurus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

131 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8575 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...