Question about 2005 Dodge Neon

1 Answer

Repairing sway bar need drawings any sugetions

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 116 Answers

Neons.org

Posted on Apr 12, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need diagram for 2000 Chevrolet Silverado ck3500 sway bar etc


Go to www.youtube.com lots of videos on the subject ! a picture is worth a thousand words , what's a video worth ?

May 16, 2015 | 2000 Chevrolet Silverado

1 Answer

We have a 2003 saturn vue tha sway bar broke , easy to disconnect, now we got a new sway bar . My question is how do we install the curvy sway bar back to its spot ?What part(s) may need taken off to get...


remove the 2 pivot points under the car on the chassis sub frame . Disconnect the rods at either end of the sway bar at the rubbers . I would get all new rubbers for the sway bar and pivots before reassembly. Sway bars normally do not break as they are spring steel so it may have been weak or rubbing on a pivot from a missing rubber

May 09, 2014 | Cars & Trucks

2 Answers

Tie rod end; and sway bar bolt broken


Those are in the factory repair manuals which we do not have. The material is copyrighted so you must buy the manual or buy digital access to it.

Mar 21, 2014 | 2004 Ford Freestar

1 Answer

Front end. i think its the "sway bar" that goes


yes that bar you are describing is the sway bar and the "links" on the ends connect the control arms so it dont roll. the links are very inexpensive like 20.00 for both and go in very easy it will only take hand tools to install . when replacing both put them in at the same time so the bar will move to install the links or you will be fighting to get the last on in

Feb 20, 2011 | 1997 Chevrolet Blazer

3 Answers

Safety says i need sway bar bushings.what and where are these?


the sway bar is a bar that runs acrossed the front of the van from strut to strut. It is bolted to the cradel and then has links that run from the bar to the strut to increase stability. The sway bar bushings are rubber mounts that hold the bar down to the cradel. The bar runs though the mounts one each side where the bar and the cradel meet. If they are wore out you will normally hear a clucking noise from the front end when you hit bumps. To remove and replace them there is two bolts that hold a steel cap on top of them on each side. Remove the cap from both sides then the rubber mounts will have a split in them so you can get them off the bar. To install them is just the reverse of the removal. Good luck! 4 thumbs up is appeciated if this helps.

Dec 30, 2010 | 2002 Dodge Caravan

2 Answers

How much to change a oil pan gasket for 2001 grand prix 3.8 gt


If you want to repair the oil pan I would also check lower engine mount for leaking oil and cracks in anti sway bar near fitting's. This due to engine mount is oil filled. OEM sway bar is made of tubular steel and they crack easy. Replacement sway bar is solid steel. Here's the kicker. When they pull the lower frame to service oil pan. The engine mount and sway bar are attached to that frame. A honest mechanic should only charge for parts ($35 for mount and $100 for sway bar) and maybe a extra hour. My mechanic did all in 5 hours. FYI gasket is only $35 bucks. Good luck

Feb 26, 2010 | 2001 Pontiac Grand Prix

1 Answer

Rear Sway bar bushings


These are not very hard to do but the nuts are usually rusted and you may need a torch. All you do is jack up the rear end of the car to release pressure on the sway bar. Then remove the nuts on the sway bar bushing bolts. Remove the assembly and put in the new ones in reverse order. Should take a couple of hours.

Jun 10, 2009 | 2000 Toyota Avalon

Not finding what you are looking for?
2005 Dodge Neon Logo

Related Topics:

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8195 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...