Question about Jeep Wrangler

1 Answer

97 jeep wrangler 6cy starts runs well until turned off then will not start for about 2 hours

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,077 Answers

The most common problem is the starter.
When the engine gets to operating temperature, the starter gets the same temperature because it's mounted next to the engine.
Most solenoids in the starter wear out with age and can't take the heat of the engine anymore.

Posted on Apr 13, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 97 jeep grand Cherokee, when it has sat for over an hour it takes 8-10 seconds of the starter running before it starts. If turned off after running, and started within a few minutes no problem,...


Fuel pump. The valve in the pump that stops the fuel from draining back into the tank is not working so you crank and crank until the fuel gets up front. Turn the key on but not to start for 5 seconds then off do it five times and then try to start it should start right up

Nov 27, 2011 | 1997 Jeep Grand Cherokee

1 Answer

97 Jeep Wrangler sport- Cranks, will not


Fuel flow. Either simply, a blocked fuel line (debris / filter / fouled gas) or an electronic issue. Ever let this Jeep run bone dry on gas? Hopefully not, as doing so can draw a lot of crud into your fuel lines from the bottom of the tank. Electronically, if part of the Jeep "brain" has gone bad, there may not be any fuel being routed to the engine. This most likely needs a Jeep mechanic to repair.

May 15, 2010 | 2007 Jeep Wrangler Unlimited Rubicon 2...

1 Answer

97 Jeep wrangler 4 cylinder manual. When in


Sounds like a bearing issue too me. Have your transmission shop take a listen.

Oct 20, 2009 | 1997 Jeep Wrangler

1 Answer

No spark from ignition module on hot start


95 JEEP WRANGLER 4 CYL

No spark. I have changed out the distributor cap, rotor, wiring from coil to cap, and coil was replaced. I checked the distibutor by turning ignition key and observing the rotor turn. What else can I check. I did not observe a module.

Jun 19, 2009 | 1995 Jeep Wrangler

2 Answers

Vehicle won't start, it has clutch interlock, which is only activated in 2wd and 4H , vehicle starts in 4L only, clutch switch??


Take it to the Jeep dealer . It's still under warranty. Won't cost you a penny. Good luck.

May 23, 2009 | 2009 Jeep Wrangler

2 Answers

97 jeep wrangler starts then stops right away, I can give it gas and get the rpms up then it just stops. I have already replaced the spark plugs, fuel injectors the wires and the rotor cap and rotor. Even...


I had the same problem with my 1997 Wrangler. I seem to of solved this by turning the ignition to off then depressing the lock on the immobilizer. Then waited for about 10-15 seconds after the red light on the dash quit blinking fast . Then I hit the unlock on the immobilizer and the Jeep started and ran ok. I guess the immobilizer is the culprit and it doesn't unlock initially

Apr 25, 2009 | 1997 Jeep Wrangler

1 Answer

92 Jeep Wrangler will not Stay running.


I had the same prblm with my 1989 Jeep, 6 cyl straight, and it was because of the EGR valve, easy to replace and not too costly. EGR valve is screwed on the motor, driver side, and there is a ±1/2" rubber hose attached. Easy to see if device comes apart, cut by rust.

Mar 18, 2009 | 1992 Jeep Wrangler

1 Answer

How do I replace the interior LH door handle 97 Jeep Wrangler?


you will need a t-20 or t-15 torx bit driver to remove 2 screws holding the handle this is all that holds them on, on once you have a replacement handle it is easier to remove 2 lower screws on the door panel and unsnap the door panel to loosen it this will allow space making it easier to reinstall new handle just slide each end into the slot and reinsert 2 screws to not fully tighten until door panel is snapped back in. the panel is held on with clips and can be released using plastic pry tool around door panel edges.

Nov 22, 2008 | 1991 Jeep Wrangler

1 Answer

97 jeep wrangler 2.5 running lean


check fuel pressure and check exhaust for leaks. exhaust leaks caqn play with the o2 sensor readings

Sep 15, 2008 | 1997 Jeep Wrangler

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

92 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...