Question about 2006 Chrysler Neon

1 Answer

2003 chrysler neon 2.0 petrol will only go into 1st gear any ideas what could be wrong

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

I am not a mech. but I own a 2002 dodge neon sxt 142,000 mi on it and have had all the regular problems with the transmision.If you have an auto trans, and it is stuck in 1st or 2nd gear here is a link that might help there are 13 parts to the video. http://www.youtube.com/watch?v=46VeVdRdkpc&playnext=1&playnext_from=QL

Posted on Sep 10, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 Dodge Neon....difficulty shifting, car shakes, cost to repair clutch? only 47,000 miles!


Sounds like you have clutch problems, this can be the hydraulic release system or the clutch plate that is defective, only a trained technician can tell the difference. Most shops will do a preliminary diagnostic for free.

Aug 07, 2012 | 2003 Dodge Neon

1 Answer

My Dodge Neon 1997 automatice shifts fine till its warmed up then will not shift out of 1st gear??????


HI, when the transmission heats up the solenoids stick and sets the transmission in fail safe mode common issue with Chrysler transmission. I would recommn\end your local transmission shop.

Aug 27, 2010 | 1997 Dodge Neon

1 Answer

2003 dodge neon, error code PO551. power steering


The Power Steering pressure switch is mounted in the pressure line between the steering gear and the power steering pump.

Good Luck

Mar 03, 2010 | 1999 Chrysler Concorde

1 Answer

Auto Chrysler Neon Petrol consuming issue


That's only 17 or 18 MPG/U.S. Gal. Not very good for a Neon. When was engine serviced last, as in air filter, oil filter , oil change, and perhaps a scan for any trouble codes? What type of driving conditions?

Jun 28, 2009 | 2006 Chrysler Neon

1 Answer

Won't shift out of 1st gear


Replace the output speed sensor on the front of the tranny. It has two wires going to it. ANd looks like a round plug with a bolt like base on it. It is also white.

May 19, 2009 | 2003 Dodge Neon

1 Answer

2002 DODGE NEON - POPPED OUT OF 1ST, WILL GO IN 2-4TH, NOT 5TH


You will need to have this Checked out by a Transmission shop. Inside the Top of the Tranny are slots for the Gear Selection. If one of these Gears looses a Tooth, It will Not go into Gear and the Gear will need to be Replaced.

Jan 24, 2009 | 2002 Dodge Neon

2 Answers

Chrysler neon lx gearbox


If you find one that has a 4-speed and the same engine size, then they will fit. What you need to watch for is that you get the correct gear ratio tranny to keep your car operating properly. I only know one way to know for sure and that is a number stamped just above the pan rail on the bottom oil pan. It will be long and have some letters at the start of it. You may be able to get that to a dealership and have them look it up. If the donor transmission is still in the car then the vehicle id number should tell you what ratio the trans is when it's looked up. That is how it's done with the US cars, it may vary a bit with the UK ones, but I am not sure.

Sep 23, 2008 | Chrysler Neon Cars & Trucks

1 Answer

Mazda 6 2.3 petrol 2002 if i select 1st gear too quickly it crunches in but if i put it in easy teres no problem it only happens in 1st gear and i put a new clutch in after the problem started and its...


1st gear syncromesh Is worn or broken. This usually is caused by forcing lever in when clutch is not disengaging fully, or changing gear with out disengaging clutch.
MMP

Aug 14, 2008 | Mazda MAZDA6 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

242 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...