Question about 2006 Mercury Milan

1 Answer

I NEED TO KNOW WERE THE IAT SENSOR IS - 2006 Mercury Milan

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 659 Answers

It is part of the mass air flow sensor it is not servicable seperately

Posted on Apr 13, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need to know what a code is po113


A code P0113 may mean that one or more of the following has happened:
  • Internally failed IAT sensor
  • Faulty connection at IAT sensor
  • Open in IAT ground circuit or signal circuit
  • Short to voltage in IAT signal circuit or reference circuit
  • IAT harness and/or wiring routed too close to high-voltage wiring (e.g. alternator, spark plug cables, etc.)
  • Faulty PCM (less likely but not impossible)

Mar 19, 2014 | 2003 Subaru Baja

1 Answer

Which are the functional iat sensor wires on an accordd 2008


It all depends on which engine your Accord is equipped with. This is really nice-to-know information when you are asking somebody for help with your engine control circuits.

For the 2.4L engine: At the MAF/IAT sensor connector, Pin #4, GREEN/BLACK is the "sensor ground" and Pin #5, RED/YELLOW is the "sensor input" for the IAT.

For the 3.5L engine: At the MAF/IAT sensor connector, Pin #1 GREEN/YELLOW is the "sensor ground" and Pin #2 RED/YELLOW is the "sensor input" for the IAT.

Oct 04, 2011 | 2008 Honda Accord

1 Answer

Wher is the IAT?


the iat sensor is located in the fresh air duct connected to the air filter in front of the fuse/relay control panel. to remove the iat sensor, renive the air filter cover and using a pair of wire cutters remove the small steel band holding the sensor in place. then by pulling on sensor it will come out. when replaceing sensor be sure to install new metal ring on new sensor to secure it in place.

Apr 28, 2010 | 2005 Dodge SRT-4

1 Answer

I need to know where my MAF/IAT sensor wires are on my 2002 V6 ford mustang


it's the sensor on the intake air duct come out of your air filter. the iat sensor is integrated with the maf sensor

Mar 13, 2010 | 2002 Ford Mustang

1 Answer

2002 chev avalanche mat sensor


I assume you are looking for the wiring for the IAT because MAT sensors are no longer used..

here you go

black / white - PCM ground
pink - fused 12-volts
yellow - MAF signal
tan - IAT sensor signal
black - IAT sensor ground

manifold temp. sensors are no loner used.

I believe you are looking for the IAT "intake air temp sensor" which is part of the mass air flow sensor.

good luck

wesleyschacht@hotmail.com

Jun 16, 2009 | 2002 Chevrolet Avalanche

1 Answer

Locating the iat sensor on a chevy tahoe 2008


Yes. That is exactly it. The Air Intake Temp Sensor is built into the Mass Air Flow Sensor on the Air Filter Box. Below is a picture...
29f8daa.jpg
6d7178d.jpg
I personally have not connected one of these Chips to a Tahoe...What I can provide you with, is the Connector Diagram so you know exactly what Wires you need to Splice in to. See below...
ce630fe.jpg
I hope this helps you. If you have any more questions or need any more diagrams, please don't hesisitate to ask...Thanks again, JShreader.

Mar 31, 2009 | 2008 Chevrolet Tahoe

1 Answer

Need location of IAT sensor on 05 F150 5.4L


the IAT is a small round sensor with 2 wire going to it, the sensor is located in the air filter housing lid or in the flexible air intake hose to the engine from the air cleaner box.

here is a picture
1ad160e.jpg

Mar 30, 2009 | 2005 Ford F-150

2 Answers

Mazda 6s IAT or MAF Wiring Schematics


What are the colors of the two IAT wires in the MAF sensor?

Aug 02, 2008 | 2004 Mazda 6

1 Answer

I NEED TO KNOW WHERE MY IAT SENSOR IS LOCATED


i need to know where is the iat sensor located on my 2003 cl3.2

Jul 24, 2008 | 2003 Acura 3.2CL

Not finding what you are looking for?
2006 Mercury Milan Logo

Related Topics:

140 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

fordexpert

Level 3 Expert

5467 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...