Question about 1995 Land Rover Range Rover

2 Answers

Tappet rattle rangerover 1995 with bmw 6 cylinder diesel engine

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

  • Expert
  • 44 Answers

Do an oil change and a flush using something like wynnes engine flush. then refill with thin oil, the oilways to the tappets might be gunked up.

Posted on Aug 21, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 88 Answers

Tapping noise is normal if engine is started but should dissapear after a few minutes when oil is dispesred at top.
Could be a lot of things without actually inspecting the engine. Had similar problems on a Ford. The hydraulic lifters packed up and could not compress or release. This forces the cam to work twice as hard. Had to remove and clean lifters 3 times. Possible cause dirt in oil or sludgy oil. Need urgent attention or be prepared to overhaul top. Other cause is too little oil at top. Check oil pump and oil pressure. Again dirty oil will enhance this problem.

Posted on Aug 19, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I set tappets of a 2.5 diesel turbo mazda


you haven't mentioned if it is a 4 cyl or not. However bring no 1 cylinder up to tdc and watch the tappets of the next cylinder to fire. when that cylinders rockers are in valve overlap situation ( exhaust starting to close and inlet starting to open) then that will be maximum clearance on no 1 cylinder and is when you set the tappets turning the engine until the next cylinder is at TDC watch for the next cylinder again to be in valve overlap and repeat as for no 1 cylinder

Dec 25, 2014 | Mazda Cars & Trucks

2 Answers

Tappets


0.20mm inlet (engine warm)
0.20mm exhaust (warm)

Apr 13, 2014 | 2003 Renault Kangoo

1 Answer

Find tdc and adjust valves on a 325 i


With the tappet cover off, rotate the engine in the normal direction of rotation until you see #4 cylinder valves rock - open/close in succession. This will be TDC on #1 - set the valve clearances. Turn the engine until your see #2 valves rock, set #5 valves, turn the engine till #6 valves rock, set # 3 valves, turn the engine until #3 valves rock, set # 6 valves, turn engine till #5 valves rock, set # 2 valves, turn engine till #1 valves rock, set # 4 valves. Once you have located #1 TDC (the second mark in the pulley should be lined up with the cover mark), it is only 60 deg. to get to the next cylinder to set. If you accidentally go past the setting point, go back and approach the setting point again in the direction of engine rotation. When you come to setting # 6 the TDC marks should be aligned again.

Jan 29, 2011 | 2003 BMW 325

1 Answer

Engine noise


You need to check the valves clearance,you must adjust it,

Mar 06, 2010 | 1995 Suzuki Esteem

3 Answers

How to adjust idle on bmw 525 tds,diesel


losen the bolts at the pump flange where it bolts to the engine block and rotate towards the engine about a 1/8 inch also adjust the linkage stop screw inwards no more than 1 1/2 turns

Jan 21, 2010 | 1995 BMW 5 Series

1 Answer

How do I change a fuel pump on my 1995 Ford F350 7.3 2WD Power Stroke Diesel Do I have to worry about the timing eccentric? How and what do I rotate?


Hi, I hope this helps...

1994-96 Engines
See Figures 3 and 4



0900c15280262dd1.jpg Fig. Fig. 3: Details of the fuel pump assembly-1994-96 diesel engine



0900c15280262dd2.jpg Fig. Fig. 4: View of the fuel pump-1994-96 diesel engine
  1. Remove the turbocharger assembly.
  2. Remove the fuel line banjo bolt at the pump.
  3. Remove the fuel line fittings at the rear of the cylinder heads.
  4. Remove the fuel lines assembly.
  5. Loosen the two hose clamps at the fuel pump fittings.
  6. Disconnect the water drain hose at the fuel filter.
  7. Disconnect the filter and position it forward.
  8. Remove the fuel pump retaining bolts, then lift the pump out of the crankcase bore.
  9. Remove the fuel pump tappet from the crankcase bore.

To install:
  1. Rotate the engine so the fuel pump eccentric is on the base circle.
  2. Install the fuel pump tappet in the base of the fuel pump.
  3. Replace the O-ring on the fuel pump base.
  4. Install the fuel pump and bolt it in place.
  5. Install the fuel filter and connect the water drain hose.
  6. Connect the two fuel hoses at the front of the fuel pump.
  7. Tighten the fuel line clamps and install the fuel filter retaining bolts.
  8. Install the fuel line assembly and new seal rings at the rear of the pump.
  9. Loosely install the fuel line fittings at the rear of the cylinder heads.
  10. Install the fuel line banjo fitting at the pump. Tighten the fitting to 40 ft. lbs. (54 Nm).
  11. Tighten the fuel line fittings.
  12. Install the turbocharger assembly.

Oct 13, 2009 | 1995 Ford F350

1 Answer

Tappet settings rangerover 2.5 dt


there is no tappet settings, they have hydraulic lifters.
if tapping its because of lack of oil changes.
the lifters are coked up and no oil fetting in.
try engine flush and new oil with hydraulic lifter additive.
if not a set of lifters.
i have got a complete head i can knick the lifters out of for £40 and the set is yours.

Apr 12, 2009 | 1995 Land Rover Range Rover

1 Answer

Transmision fluid


i didn't think you could check the transmission fluid level (auto trans) on a 6 or 8 cylinder BMW engine. its suppose to be "lifetime" fluid on the newer cars.

Jan 30, 2009 | BMW 325 Cars & Trucks

2 Answers

Engine code


Dear sarah,

engine number is listed on the owner registration card. or you can ask those making tools to make /fabricate one for you.

Oct 01, 2008 | 1995 Land Rover Range Rover

Not finding what you are looking for?
1995 Land Rover Range Rover Logo

398 people viewed this question

Ask a Question

Usually answered in minutes!

Top Land Rover Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75197 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Land Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...