2012 Toyota Camry Logo

Related Topics:

A
Anonymous Posted on Aug 21, 2013
Be the first to answer

Timing balance shafts on 2ar fe toyota - 2012 Toyota Camry

Answer This Question

2 Related Answers

Anonymous

  • 1 Answer
  • Posted on Jan 24, 2010

SOURCE: toyota tarago 2az fe motor

Rustam.Where is the fuse for radio of 2003 toyota tarago

Ad

Anonymous

  • 1874 Answers
  • Posted on May 12, 2011

SOURCE: timing balance shafts on 2az

1. Remove the fan and generator V belt:

tdisline_502.jpg
tdisline_503.jpg
2. TIMING CHAIN (2az-FE Engine):
Before servicing the vehicle, refer to the Precautions Section.
Drain the engine oil.

Remove or disconnect the following:
Negative battery cable

Hood Right-side front wheel Engine under covers Right-side fender apron seal Front exhaust pipe Engine moving control rod and bracket Right-side engine mounting stay and bracket Accessory drive belt Engine appearance cover Engine wire Alternator Power steering pump, leave the hoses connected Ignition coils Ventilation hoses Cylinder head cover Turn the crankshaft pulley to set the No. 1 cylinder to TDC compression. Align the groove on the pulley with the timing mark -0- on the front cover. Remove the crankshaft pulley as follows:

  1. TMC made: Use Special Tool 09213-54015 to hold the pulley to loosen the bolt. Use Special Tool 09950-50013 to remove the bolt and pulley.
  2. TMMK made: Use Special Tool 09960-10010 to hold the pulley to remove the bolt. Use Special Tool 09950-40011 to remove the crankshaft pulley

tdisline_504.jpg
Fig. Removing the crankshaft pulley-TMC-2.4L (2AZ-FE) engine

tdisline_505.jpg

Fig. Removing the crankshaft pulley-TMMK-2.4L (2AZ-FE) engine


  • Remove or disconnect the following:

    Crankshaft position sensor Lower oil pan No. 1 chain tensioner Accessory drive belt tensioner
  • Support the engine with a suitable engine lifting device.
  • Remove or disconnect the following:

    Engine mounting insulators Right-side engine mounting bracket Stud bolt for the accessory drive belt tensioner from the block Front cover mounting bolts and nuts Front cover Crankshaft position sensor plate Timing chain tensioner slipper Timing chain vibration damper Timing chain Crankshaft timing sprocket
  • Turn the crankshaft counterclockwise by 90°, and align an adjusting hole of the oil pump driven sprocket with the groove of the oil pump.
    • tdisline_506.jpg
    Fig. Align the adjusting hole of the oil pump drive sprocket with the oil pump groove-2.4L (2AZ-FE) engine

    tdisline_507.jpg
    Fig. Insert a bar to lock the sprocket in position-2.4L (2AZ-FE) engine
    1. Put a bar in the adjusting hole of the oil pump driven sprocket to temporarily lock the sprocket in position. Remove the nut.
    2. Remove the bolt, chain tensioner and spring.
    3. Remove the chain tensioner, oil pump sprocket and No. 2 timing chain.

    To install:
    1. Set the crankshaft key into the left horizontal position. Turn the cutout of the drive shaft to the top.


    tdisline_508.jpg


  • Fig. Align the crankshaft key and drive shaft cutout as shown for installation-2.4L (2AZ-FE) engine

  • Align the yellow colored links with the timing marks of the sprocket as shown in the illustration.
  • Insert the sprockets with chain to the crankshaft and oil pump shaft.
  • Temporarily tighten the oil pump driven sprocket with the nut.
  • Insert the damper spring into the adjusting hole, and install the chain tensioner plate with the nut. Tighten to 9 ft. lbs. (12 Nm).
  • Align the adjusting hole of the oil pump driven sprocket with the groove of the oil pump.
  • Put a bar in the adjusting hole of the oil pump driven sprocket to temporarily lock the sprocket in position. Tighten the nut to 22 ft. lbs. (30 Nm).
  • Rotate the crankshaft counterclockwise by 90°, and align the crankshaft key to the top.
  • Install the timing chain vibration damper. Tighten to 80 inch lbs. (9 Nm).
  • Align the timing marks of the camshaft timing sprockets and bearing caps.
  • Using the crankshaft pulley bolt, turn the crankshaft and set the set key on the crankshaft upward.
  • Align the gold or orange colored link with the timing mark of the crankshaft timing sprocket.
  • Using Special Tool 09309-37010, tap in the sprocket.
  • Align the gold or yellow colored links with the timing marks of the camshaft timing gear and camshaft timing sprocket. Install the chain.
    • tdisline_509.jpg

    Fig. Align the marks of the sprockets and bearing caps to set the No. 1 cylinder at TDC-2.4L (2AZ-FE) engine

    tdisline_510.jpg

    Fig. Set the crankshaft set key facing upward-2.4L (2AZ-FE) engine

    tdisline_511.jpg
    Fig. Align the marked link of the timing chain with crankshaft sprocket timing mark-2.4L (2AZ-FE) engine

    tdisline_512.jpg

    Fig. Tap the crankshaft sprocket in with Special Tool 09309-37010-2.4L (2AZ-FE) engine

    tdisline_513.jpg Fig. Align the marked links of the timing chain with the camshaft sprockets during installation-2.4L (2AZ-FE) engine

    Add Your Answer

    ×

    Uploading: 0%

    my-video-file.mp4

    Complete. Click "Add" to insert your video. Add

    ×

    Loading...
    Loading...

    Related Questions:

    1helpful
    1answer

    2002 Hyundai Santa fe 2.4 L engine. Why is there 10 lb compression in 1 and 4 cylinders,and 0 in 2,3 cylinders? No problems found with timing belt and timing, no problems with balance shaft.
    possible reasons
    1--- valve damage from broken timing belt
    2 --- broken timing belt
    Read full answer
    Nov 28, 2016 • Hyundai Cars & Trucks
    0helpful
    1answer

    How do I replace the oil pump on my 2001 Toyota rav4
    You have to take the front covers off the engine and while you are that far into the engine you should replace the timing chains; there are kits of all parts needed available. Here is a link with lots of good information:
    1az fe balance cam shaft
    Read full answer
    Jan 29, 2015 • 2001 Toyota RAV4
    0helpful
    1answer

    Is it a mandatory to include metal plate when replacing water pump on toyota rav 4
    no year, you are kidding,right?
    mandatory, metal plate?
    what year, what engine.
    see here and see why we dont know.
    like 20 engines there.

    http://en.wikipedia.org/wiki/Toyota_RAV4

    xa30 gen 3
    this is why we are clueless, that is ok 90% of posts never say.
    2.0 L 1AZ-FE I4 (petrol)
    2.0 L 1AZ-FSE I4 (petrol)
    2.0 L 3ZR-FAE I4 (petrol)
    2.2 L 2AD-FTV I4 (diesel)
    2.2 L 2AD-FHV I4 (diesel)
    2.4 L 2AZ-FE I4 (petrol)
    2.5 L 2AR-FE I4 (petrol)
    3.5 L 2GR-FE V6 (petrol)
    Read full answer
    Jul 07, 2014 • Cars & Trucks
    1helpful
    1answer

    Where is the knock sensor
    on the side of the engine,
    why do you need to know that.?
    they never fail unless hit with a hammer.
    the answer is in the FSM (no engine options stated so impossible to answer prefectly)
    its at alldata.com, but you need engine size.
    here is the engine list just for all (in year span) RAV4

    2.0 L 1AZ-FE I4 (petrol)
    2.0 L 1AZ-FSE I4 (petrol)
    2.0 L 3ZR-FAE I4 (petrol)
    2.2 L 2AD-FTV I4 (diesel)
    2.2 L 2AD-FHV I4 (diesel)
    2.4 L 2AZ-FE I4 (petrol)
    2.5 L 2AR-FE I4 (petrol)
    3.5 L 2GR-FE V6 (petrol)
    world wide, and you never said what country either.
    Read full answer
    Feb 05, 2014 • 2010 Toyota RAV4
    0helpful
    1answer

    BALANCE SHAFT SETUP MARKS FOR TOYOTA 2AZ-FE MOTOR
    A LOT OF SHOPS ARE HAVING TROUBLE SETTING THE BALANCE SHAFTS ON THE 2AZ-FE (AND IF YOU ARE ONE TOOTH OFF YOUR ENGINE WILL BLOW UP ) I AM A TOYOTA TECH AND HAVE SEEN THE DAMAGE THAT INCORRECT BALANCE SHAFT TIMING CAN CAUSE THERE IS A TOOL COMPANY CALL (TIMING SOLUTIONS) THE TOOL IS CALLED (THE 2AZSAVER) THIS TOOL COMES IN A CASE WITH VERY DETAILED VIDEO ON HOW TO PROPERLY SET BALANCE SHAFT TIMING ,THIS TOOL MAKES SETTING BALANCE SHAFTS VERY EASY
    Read full answer
    Feb 18, 2013 • Toyota Camry Cars & Trucks
    2helpful
    1answer

    Timing balance shafts on 2az fe toyota
    Take a look at the engine below with chain installed

    9_24_2012_11_26_48_pm.jpg
    Read full answer
    Sep 24, 2012 • 2003 Toyota Camry
    0helpful
    1answer

    2002 santa fe 4 cylinder engine had timing belt and balance shaft belt replaced after balance shaft belt broke now engine pigs alot and doesnt have any power cuts out above 3000 rpms
    its out of time should be warranty on belt hopefully no bent valves and or holes in pistons
    Read full answer
    Jan 21, 2011 • 2002 Hyundai Santa Fe
    24helpful
    3answers

    Me puedes proporcinar la posicion de la cadena de tiempo para una tacoma 4 cilindros motor 2.7 3RZ
    Revice los siguientes diagramas para 2002 Toyota Truck Tacoma 2.7L EFI DOHC 4cyl (click over pic for zoom)...

    zjlimited_521.jpg

    Fig. Timing chains and related components-2.4L and 2.7L (3RZ-FE/M) engines

    zjlimited_522.jpg

    Fig. Check that the No.1 cylinder is at TDC and the weights of the No.1 and No.2 balance shafts are at the bottom-2.4L and 2.7L (3RZ-FE/M) engines

    zjlimited_523.jpg

    Fig. Crankshaft position sensor rotor location-2.4L and 2.7L (3RZ-FE/M) engines

    zjlimited_524.jpg

    Fig. No.1 timing chain and camshaft timing sprocket identification and alignment-2.4L and 2.7L (3RZ-FE/M) engines


    Espero que le sea de ayuda (recuerde valorar esta respuesta).
    Read full answer
    Jan 20, 2011 • 2002 Toyota Tacoma
    0helpful
    1answer

    Balancer shaft came apart ???????? crankshaft pulley keeps throwing balancer car won't accelerate balencer shaft timing marks keep coming off on recheck of timing belt new tps ,converter howlled for test...
    Sounds like the harmonic balancer - that also serves as the timing on a non distributor car has stripped the threads out. This usually - not always but usually requires a new crank shaft. Might be cheaper to just get a used engine.
    take down the vin number and ask the local dealer if there have been any recalls or service bulletins
    Read full answer
    Dec 05, 2009 • 2001 Hyundai Santa Fe
    1helpful
    2answers

    Toyota tarago 2az fe motor
    Rustam.Where is the fuse for radio of 2003 toyota tarago
    Read full answer
    Jul 05, 2008 • 2003 Toyota Camry
    Not finding what you are looking for?

    View Most Popular

    2012 Camry

    • Cars & Trucks

    Related Question

    2002 Hyundai Santa fe 2.4 L engine. Why is there 10 lb compression in 1 and 4 cylinders,and 0 in 2,3 cylinders? No problems found with timing belt and timing, no problems with balance shaft.

    • Hyundai Cars & Trucks

    2,511 views

    Ask a Question

    Usually answered in minutes!

    Popular Questions

    How to fix diagnostic code p0442

    2003 Toyota Camry

    Electric front seat stuck

    2003 Toyota Camry

    I have relay saying :mg clt what is that mean?

    2003 Toyota Camry

    Starter making whining noise

    1995 Toyota Camry

    VSC Trac off lights on dashboard

    2003 Toyota Camry

    Check Out the Latest Top Trucks Report!
    Check Out the Latest Top Trucks Report!

    View all Fixya Reports

    Top Toyota Experts

    ZJ Limited
    ZJ Limited

    Level 3 Expert

    17989 Answers

    Thomas Perkins
    Thomas Perkins

    Level 3 Expert

    15088 Answers

    ROBERT GARCIA
    ROBERT GARCIA

    Level 3 Expert

    926 Answers

    Are you a Toyota Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    PDF Manual
    Toyota_2012_CAMRY_LE-2012-02-20-1.pdf....

    2012 Camry

    Loading...