Question about Cars & Trucks

Open Question

Specs and photos of 1960 thames trader 4 cyl petrol engine

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Engine stops when 14 liters left in tank

For the time beeing I do not run to lowlevel in fueltank. I am going to take out the tank and find out if it is a pipe that is corroded or if it is some problems with the filter inside the tank.
I thought that somebody did have the same problem.
Eventually I will buy a replacement tank. If I decide to do so, I will cut the old tank and see what caused the problem.

Thanks for your mail

Best rgds
Kurt

Posted on Dec 21, 2008

Ad
johnny5846
  • 379 Answers

SOURCE: need the torque specs for

  1. Tighten the cylinder head bolts a little at a time, in the sequence shown. Tighten the bolts in three stages:
    • First pass: 25 ft. lbs. (34 Nm)
    • Second pass: 45 ft. lbs. (61 Nm)
    • Final pass: 65 ft. lbs. (90 Nm)
http://www.autozone.com/addVehicleId,1938903/initialAction,repairGuide/shopping/repairGuide.htm?pageId=0900c1528008eed5

scroll down to about half way down the page , there is step by step procedure for the 1994 5.7 L head installation and torque and tightening sequence . handy dandy site . cheers .

Posted on Jan 11, 2009

  • 25 Answers

SOURCE: 87 samurai bolt torque specs for engine

The haynes book is not recommended since there are numerous mistakes and they still will not update. One of the biggest is the firing order.

The factory service manual is the only way to go.

Head bolts - 46 - 50.5 lbs (there is an order sequence for the bolts)

Intake & exhuast manifolds- 13.5 - 20 lbs

Flywheel - 41.5 - 47 lbs

Clutch cover - 13.5 - 20 lbs

Posted on Mar 17, 2009

  • 14036 Answers

SOURCE: need torque specs for rod bearing caps on 1995 toyota terel 4 cyl

1.6 engine 36 ft lbs 1.8 engine 36 ft lbs 2.0 engine 49 ft lbs

Posted on Apr 11, 2009

  • 571 Answers

SOURCE: 2002 Toyota Camry Engine Torque Specs 2.4 L. 16 V.

Petrol engine 2362 ccm
Max torq: 218 Nm at 3800 rpm
Max power: 152 hp at 5600 rpm
Compression 9.6:1

Posted on Nov 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Isuzu kb 320 v6 noisey rockers


ill look up the specs to see if they are adjustable valve clearance like the 4 cyl petrol engine. if they are adjustable ill give you the clearances recommended if they happen to be hydraulic the best bet is a engine oil and filter change and with any luck that alone will help it out some what. may also be a idea with the engine running remove the oil filler cap and see visually that there is ample oil being splashed around rockers and cam shaft etc. hope to be able to help you with your problem

Mar 09, 2014 | 1994 Isuzu Pickup

1 Answer

Cant find torque settings for a mazda XA 3.0L 4 cylider


older mazda diesels e3000 (3litre) were often rebadged to ford traders I have a book on that diesel (E3000)and if it is the same I can give you the specs but to find you again I will require you to send a reply comment. It may take me some time to dig up the book so if you will reply comment I will send you what I have

Dec 25, 2013 | Mazda B-Series Truck Cars & Trucks

1 Answer

Need wiring diagram for 1955 ford


1955 ford what ?? a E93A 6v system or a ford zephyr ,ford pilot thames van or thames trader truck

Aug 01, 2012 | Mercury Montclair Cars & Trucks

3 Answers

Cannot adjust clock on 59 plate Ford C max. handbook instructions don't help


if this vehicle has been parked in the sun then sometimes this destroys the clock ,would help if i knew the year and not this funny secret code they use in the UK i think it is ,59 plate??? what is this is it a 1959 model like a mk2 consul or a 100E ,even a thames trader ,does the engine start with a 204E or is it a side valve ??

Mar 27, 2011 | 2004 Ford Focus

2 Answers

Firing order


6 cyl 1-6-5-4-3-2

Jan 21, 2011 | 1986 Oldsmobile Ciera

1 Answer

Engine misfires on #1 cyl. Code P0301. plug, fuel


Then the coil is bad. Even if the specs were ok, which they r not, the cracked case means its junk.

Jan 29, 2010 | 2001 Ford Taurus

1 Answer

2002 Toyota Camry Engine Torque Specs 2.4 L. 16 V. 4 Cyl.


Petrol engine 2362 ccm
Max torq: 218 Nm at 3800 rpm
Max power: 152 hp at 5600 rpm
Compression 9.6:1

Nov 26, 2009 | 2002 Toyota Camry

1 Answer

Need torque specs for rod bearing caps on 1995 toyota terel 4 cyl


1.6 engine 36 ft lbs 1.8 engine 36 ft lbs 2.0 engine 49 ft lbs

Apr 11, 2009 | 1995 Toyota Tercel

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...