Question about 2000 Ford Mustang

1 Answer

2000 mustang 3.8 run but when get hot its cut offf & want start until cool. I turn ignition on here harming noise on passenger side by fender, pull sparkplug wire off to see was firing was not, put new coil & still not firing. Could someone tell me what would be the problem?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 17 Answers

Change the coil coils heat up and short out

Posted on Aug 02, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 4 Answers

SOURCE: ignition wiring

firingorder6a.gif firingorder6.gif 1991-1994 2.9L and 3.0L Engines Firing Order 1-4-2-5-3-6 1995 And Later 3.0L V-6 With DIS Ignition System Firing Order 1-4-2-5-3-6
4.0L Engines Firing Order: 1-4-2-5-3-6 DIS Ignition System

Posted on Nov 23, 2008

  • 1 Answer

SOURCE: MY 1997 EXPLORER STARTS BUT WONT STAY RUNNING .

I had the same exact problem with my 1998 Explorer and it was the Idle Air Control. You can try to remove and clean it but it won't last very long. I replaced it myself in 5 minutes and an expense of $80. Hope this helps.

Posted on May 06, 2009

  • 15 Answers

SOURCE: Hesitation and stumbling.

Before you do that, check which thermostat it has in it, if it has one that is letting it get too warm or not completely up to temp when the computer think it should be, it would cause this. My 2000 crown vic did the same thing and thats what it was.

Posted on Jul 20, 2009

jlisagearhea
  • 412 Answers

SOURCE: For Ford F-150 P/U 351 EFI, 1988, ignition problem

unfortuneately there is no shortcuts....But if there was for sure I'd tell you...it's really not hard....just take off the panelling on the lower and you can sneak it in and out...get back to me...I'M HERE TO HELP!!

Posted on Nov 18, 2009

Testimonial: "hey everybody these answers are on the money...., everyone should get this type of service from their auto service center thank you for your help jame"

  • 593 Answers

SOURCE: 1965 Mustang 289 2v 2100 carb. The car runs fine

It sounds like the choke may not be opening completely. Check the choke tube from the choke assy. to the exaust manifold. The tube often breaks off at the manifold. There was a repair kit from a co.
called toke.(it was the 60's)The part# was ux-1 it had a new copper tube+sleeve and a fitting, that you would place over the broken piece in the manifold tap
it with a hammer and it knocks out the old + installs
the new fitting. Push in the new tube and install the
other end into choke assy. If it's an elec.choke check
the voltage at the wire to the choke assy. it should be between 7-12 volts, if not check for a fuse in line or at
the fuse block. I don't recall exactly where it is. But if
neccesery you can run a new wire with a 20amp in
line fuse, from the choke plug to the S(stator)connection on the alternator. This will provide enough
juice to expand the bimetal spring in the choke housing. And only when it's needed. When the engine is running..Also the choke can be adjusted
whether it's the tube or elec. You can adjust the choke spring by turning the black plastic cover.
There should be 2 arrows pointing clockwise+counter
clockwise. After the choke is fixed you can fine tune
it by loosining the 3 screws and turning to rich or lean as needed. Hope this helps.

Posted on Mar 31, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

4 Answers

What is the solution for the durango turning off while driving? mine-2000 5.9 4wd


I would take it to an autoparts store that does a free 'code scan' and see if the computer has captured the failure. I suspect this is computer related issue so the code(if any) could be misleading. Had an 90's model New Yorker in the 90's shutting down for no reason and replacing the computer fix it.

That said a battery getting old (most commonly) or something in the electrical system not working correctly can cause a good computer to malfunction. Have the battery tested as well or switch to known working battery.

Jun 02, 2014 | 1999 Dodge Durango

1 Answer

My 2000 Buick LeSabre runs cold, after it is turned off it will not start again.


it sound to me you have starter problem tune your ignition on and try to jume starter hope this help

Jul 14, 2012 | 2000 Ford Taurus

1 Answer

Air works fine, no heat


First check your coolant level. If that is good then it could either be a clogged heater core, or there is a little servo motor under the passenger side dash board that controls the blend air door and the hot coolant flow into the heater core. One way to check it and it requires some bending and twisting. With the vehicle running look up under the passenger side dashborad and there will be a little servo with an arm attached to it. Next turn on the system on with the auto switch and push the button for cool then push the button for hot until it is maxed out to 90 degrees. Then observe if the servo lever moves, if not then more than likely its that servo. Sometimes it will make a banging noise or it could just be burnt out.

Dec 06, 2011 | 2000 Acura TL

1 Answer

How do you replace an antenae on a 1965 mustang.


Disconnect the cable at the radio. Then unscrew the hardware holding the antenna to the fender. Then pull the antenna base out of the fender, disconnect the cable from the antenna base turning it back and forth with pliers or you can cut it. Do not let the cable fall back into the fender. Now take the cable from the new antenna and duct tape it to new antenna cable. Now inside the car pull on the old cable until the new cable reaches the radio. Plug cable into radio then hook up the hardware on the fender for the new antenna and you're done. Good luck.

Feb 27, 2010 | 1965 Ford Mustang

1 Answer

Run greats for 5mins then cuts offf an will not start until cooled down.


replace the ignition module,they are bad to do this on these years.

Nov 14, 2009 | 1989 Buick Park Avenue

1 Answer

Replace front side running light in a 2000 Lexus RX300


Unscrew 3 - 4 screws on the front tire fendor cover close to your side marker light. Pull the fender cover out, use your other hand to reach the side marker light. Using twist and pull the light set out. Replace a new light bulb. Replace everything in a reverse order.

Mar 18, 2009 | 2000 Lexus RX 300

3 Answers

2001 ford mustang no power to fuel pumps


check your fuel pump cut out switch. located in the front passenger side kick panel area in the floor board, the safety switch could need resetting

Jan 28, 2009 | 2001 Ford Mustang

Not finding what you are looking for?
2000 Ford Mustang Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5467 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...