Question about Cars & Trucks

1 Answer

I have a 1994 Buick Century. My problem is my power locks, they will not lock with the switches in either door. They lock when the car is put in drive and unlock just fine with the switches, but will not lock with the switches.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

  • Contributor
  • 2 Answers

Nuetral

Posted on Aug 02, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: 92 F150 power window and locks

try taking apart and cleanig all contacts first. make sure you are getting power to switch. Sounds more switches are going bad. They usually last about 5 to 7 years before they start going out.

Posted on Jun 11, 2008

  • 61 Answers

SOURCE: Power door locks won't work

You need to have someone or yoursef check the body control module with a compatible scan tool. Thats where the problem you are having resides. It may need a software update or replacement. You can also disconnect the battery for a few minutes, that will cause the BCM to reset and may fix it.

Posted on Jan 28, 2009

  • 1596 Answers

SOURCE: power door lock switch replacement




Remove or Disconnect

Door handle trim plate.

  1. .Install or Connect

  2. Electrical connector and door lock cable.
  3. Trim panel by engaging hooks on backside of panel.
  4. Push pin fastener in defroster duct.
  5. Screw from behind lamp assembly.
  6. Courtesy lamp assembly.
  7. Two screws in arm rest.
  8. Arm rest cover plate.
  9. Door handle trim plate.
There May Be A Need to Drill Out RIVETS that Hold Motor in place,. Just Replace with>>MACHINED SCREWS & BOLT'S




Remove or Disconnect

  1. Trim panel. See: Doors, Hood and Trunk\Doors
  2. Four tabs retaining switch.
  3. Electrical connector.
Install or Connect

  1. Electrical connector.
  2. Snap switch into trim panel.
  3. Trim panel.

Posted on Mar 14, 2009

cadman000
  • 607 Answers

SOURCE: rear door lock will not lock or unlock

sounds like that rear door lock will also not unlock with the switch either, correct ? It might lock , but not unlock. Door lock actuator needs to be replaced.

Posted on Apr 01, 2009

  • 1 Answer

SOURCE: 1994 Buick Skylark. Lot of hesitation and jerking, power locks

HI MY NAME IS JUAN:
I HAVE A 93 BUICK SKYLARK CUSTOM
AND I HAD THE SAME HESITATION.
I CHAGED GAS FILTER, AIR FILTER, AND USE SEA FOME IN MY GAS TANK AND USE IT ALSO TO CLEAN THE INTAKE SYSTOM, AND IT HELPED ALOT. TWO MONTHS DOWN THE LINE HADE THE SAME HESITATION AND IT WAS ONE OF THE INISION COIAL PACK WAS NOT GIVING THE ELETRICAL SPARK TO THE PLUG. I CHECK IT BY PULLING THE CABLE OFF THE SPARK PLUG WITH THE CAR RUNNING AND FOUND THE ONE THAT WAS NOT GIVING SPARK. I REPLACED THE PACK FOR THAT CILINDERS PLUG AND THE PROBLEM WAS GONE.
HOPE THIS CAN HELP YOU.

Posted on Sep 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 buick century door locks not working with remotes


check your fuses most likely blew the fuse

Feb 28, 2013 | 2000 Buick Century

1 Answer

Where is the power window relay located on the '03 Buick Century? And could this be the problem for all windows to stop working at the same time EXCEPT the driver's window? Or possibly the lock switch not...


The lock switch is designed to keep the passenger buttons from being used. It should not stop the master switch from operating the windows - or at least, that's what the 2003 Buick Century Owner's Manual says.

After studying the schematics for your vehicle, Iwould say that the owner's manual is correct. The lockout switch only cuts power to the passenger switches. The driver's (master) switch can still power the passenger windows. If none of the passenger windows work from either the driver's door switch or the passenger switches, then the master switch probably has an internal open circuit causing this. There is no separate relay or fuse. I would replace the master switch. Be sure and check ALL switches with the lock on and the lock off to verify this before replacing anything.

Feb 19, 2011 | Buick Century Cars & Trucks

1 Answer

My 1993 buick century has power doorlocks that remains locked whenever I put the car in park. how can i disable the power door locks?


i dodnt think you can, personally i thought it ws a stupid idea , its supposed to make sure you car is locked when you exit, try the cavalier owners website, might find the answer there

Nov 11, 2010 | Buick Century Cars & Trucks

2 Answers

98 buick century power windows dont work


CHECK POWER WINDOWS 20 AMP CIRCUIT BREAKER.

Jan 24, 2010 | 1998 Buick Century

1 Answer

Where do I find the instructions for programing a buick century 1997 keyless remote?


METHOD 1 - NO TOOLS REQUIRED

  1. Sit in the vehicle driver's seat.
  2. Remove the ignition key from the ignition lock cylinder.
  3. Close all of the vehicle's doors.
  4. Press and HOLD the door "LOCK" switch to the "Unlock" position.
  5. Insert and remove the ignition key twice (without rotating the ignition lock cylinder).
  6. Insert the ignition key a third time leaving the key in the ignition lock cylinder. The ignition must be in the "OFF" position.
  7. Release the door "LOCK" switch from the "Unlock" position (three fast chimes will be heard when the remote control door lock receiver enters the programming/diagnostic mode).
  8. Press and HOLD the transmitter "LOCK" and "UNLOCK" buttons simultaneously for at least 12 seconds . Two fast chimes will be heard confirming successful programming.
  9. Repeat step 8 for each additional transmitter to be programmed.
  10. Remove the ignition key from the ignition lock cylinder

Sep 26, 2009 | 1997 Buick Century

2 Answers

2002 Buick Century locks its doors automatically and constantly


i dont see this as a major or even minor problem, why is it bothering you? if you wanna idle your car in drive whats the point? if your just waiting for someone to come in, put it in pak and the door will unlock BY THEMSELVES, sounds good to me, and then after the person jumps in put in in drive/reverse.... or u can simply leave it in gear THEN unlock it, the back doors dont have power lock button so they have to do it manually or if youre in park they dont have to do it at all. its a nice feature 1 in a million would actually not like this feature

May 01, 2009 | 2002 Buick Century

1 Answer

1996 BUICK CENTURY 4DR


check there drivers door jamb they will break inside the rubber boot you can also run a new ground through there to solve the problem good luck and please rate -jeff

Sep 05, 2008 | 1996 Buick Century

1 Answer

1998 buick century windows are no longer going up or down with full power and some times take several tries to get them up


what wire do i disconnect to stop the doors from locking when i put it in cear 1992 buick century

Jul 29, 2008 | Buick Century Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...