Question about Cars & Trucks

Open Question

Cylinder head torque settings for a 2005 Mazda 3 1.6 dynamic

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 98 Answers

SOURCE: how to rebuilt the cylinder head of daihatsu charade 3 cylinder engine

Which motor?

Posted on Sep 04, 2008

Ad
c17hydro
  • 2984 Answers

SOURCE: cylinder head torque settings 1990 2.6L isuzu motor

From front to back is this:


7 3 1 5 9



8 4 2 6 10



First torque value is 58 ft lbs.....then final torgue is 72 ft lbs.

Posted on Mar 21, 2009

NismoMaster
  • 146 Answers

SOURCE: torque settings for cylinder head nissan sentra

Tighten in sequence to 29ft.lbs then tighten in sequence to 58ft lbs. then loosen all bolts. Then tighten in sequence to 33ft lbs. then tighten each bolt in sequence 90 degrees then tighten each bolt again 90 degrees

Posted on Jul 26, 2009

  • 88 Answers

SOURCE: Hi I'm looking for cylinder head torque settings for a 1992 BMW 316/318 e36

BMW cylinder torque setting all models

According to my service manual as follows.

Cyl head to engine block (torx e12 M10 bolts)

Stage 1 30nm (22 ft – lb)
Stage 2 + 90 degrees
Stage 3 + 90 degrees

Cyl head to lower timing chain cover 10nm (89in – lb)

The tightening sequence is from inside to outside crossover as normal. Loosening sequence is from outside to inside crossover. Remember to set torque wrench at low setting and work gradually up through the whole sequence until you get the desired torque.

Posted on Aug 29, 2009

inspectmycar
  • 233 Answers

SOURCE: 94 mazda B3000 3.0L cylinder head torque specs

Step 1 torque to 59 ft pounds
2. Loosen one full turn
3. 37 ft pounds
4. 68 ft pounds

Use torque sequence below
aca9f77.gif

Posted on Sep 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How much is the engine head of Mazda 3 1.6 2007 16 v


Mazda 3 Cylinder Head ' eBay

www.ebay.com/bhp/mazda-3-cylinder-head
eBayEngine Cylinder Head Bolt Set Fel-Pro ES 72207 (Fits: Mazda 3) ... 2.0l & 2.3l dohc l416v, w/ turbo, "duratec" 2004 - 2009 mazda 3 2.3l dohc l4 16v. 2007 - 2009 ... #O608 RIGHT CYLINDER HEAD 2007 MAZDA3 2.0 MANUAL 4683894AC.

Oct 29, 2015 | Mazda Cars & Trucks

2 Answers

Need torque settings for mazada 3 1,6 z6 engine


Hi,

I've attached an image showing the torque settings for the major items. I hope this helps.

25295932-albj1arptdcaeoel3c43zd1z-4-0.png

Nov 24, 2014 | Mazda MAZDA3 Cars & Trucks

1 Answer

What are the torque specs of the head bolts of a Mazda protege 94


step 1 17-19 ft/lb
step 2 90 degrees
step 3 additional 90 degrees
engine uses Torque To Yield head bolts
New head bolts must be used when cylinder head is replaced or re-installed

stockam auto

Jul 05, 2011 | 1994 Mazda Protege

1 Answer

I need troque setting for cylinder head bolts for Madza MX3


zjlimited_1139.jpg

Fig. 1: Cylinder head bolt tightening sequence for all 4-cylinder engines


1. Clean the cylinder head bolts and the threads in the block. Make sure the bolts turn freely in the block.

2. Install a new head gasket on the engine block. Make sure the camshaft sprocket timing marks are still aligned, as set during the removal procedure. Install the cylinder head.

3. Lubricate the bolt threads and seat surfaces with clean engine oil and install them. Torque the bolts in 2-3 steps to 56-60 ft. lbs. (75-81 Nm) in the proper sequence.

Hope helps.

Apr 29, 2011 | 1995 Mazda MX-3

1 Answer

What is the cyl head torque setting for 05 vw golf 1.4 fsi 16v


Cylinder head instructions

tdisline_358.jpg
Cylinder head torque setting for 2005 VW Golf 1.4 FSI
Renew bolts
Stage 1 = 30 Nm
Stage 2 = 90 degrees
Stage 3 = 90 degrees

Mar 23, 2011 | Volkswagen Golf Cars & Trucks

1 Answer

Correct pressure for torque the head of mazda pickup 1998


Since you didn't say which engine you have, I've pulled torque specs for 3 different engines. Also, since I can't include a diagram showing the relative locations of the numbered head-bolt locations, it would be a good idea for you to purchase a vehicle specific repair guide that will show this info.


Take particular note about the TTY (Torque to Yield) bolts used on 2 of the 3 engines shown. It is said that new head bolts MUST BE USED when head is replaced or re-installed to obtain the proper torque.



B2500 4 Cylinder

Torque sequence: --------- ' 10 6 2 4 8 ' front ' ' ' 7 3 1 5 9 ' -----------Step 1: torque in sequence to 51 Ft/Lbs Step 2: torque again in sequence to 51 Ft/Lbs Step 3: final tighten all bolts an additional 90 to 100 degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.







B3000 3.0 6 Cylinder

Torque sequence ---------- ' 6 4 2 8 ' ' ' ' 5 1 3 7 ' ---------- Step 1: torque to 59 Ft/Lbs Step 2: loosen in sequence (1) full turn Step 3: torque to 41 Ft/Lbs Step 4: torque to 73 Ft/Lbs









B4000 4.0 6 Cylinder

Torque sequence --------- ' 5 1 3 7 ' ' ' ' 6 4 2 8 ' --------- Step 1: torque cylinder head bolts in sequence to 26 Ft/Lbs Step 2: torque cylinder head bolts to 56 Ft/Lbs Step 3: turn cylinder head bolts in sequence an additional 90-degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.


Good luck with this job!

Feb 06, 2011 | 1998 Mazda Pickup

2 Answers

I have been told that you have to replace the head bolts when replacing the head gasket because the bolts will stretch. Is this true?


If you change the head bolts that's the safest bet for trouble free operation. But, I've changed head bolts on Hondas for years and they never stretched. I know this is for a Kia. My best guess is that it's not necessary since the Chilton based manuals don't say to do this.

If the head is torqued down to specifications and it leaks, then I would say, otherwise. Even torque is more important than bolt stretch, especially if the bolts don't stretch so much that the head gasket can't be tight against the head and block.

Jan 31, 2011 | 1999 Kia Sportage

1 Answer

Changing head gasket torken head down - settings


Here is a picture of torque pattern for a 2200 2.2L
Tighten the cylinder head bolts in 2-3 steps in the proper sequence. The final torque specification is 59-64 ft. lbs. (80-86 Nm).

chuckster57_18.gif

Jan 24, 2011 | 1992 Mazda B-Series

1 Answer

Engine head torque settings


2.0L 4 cylinder

cylinder head bolt torque

step 1 13-16 ft lbs.

step 2 additional 85 degrees

step 3 additinoal 85 degrees

2.5L V6

head bolt torque

step 1 17-19 ft lbs.

step 2 additinoal 85-95 degrees

step 3 additinoal 85-95 degrees

Mar 23, 2010 | 1998 Mazda 626

1 Answer

94 mazda B3000 3.0L cylinder head torque specs


Step 1 torque to 59 ft pounds
2. Loosen one full turn
3. 37 ft pounds
4. 68 ft pounds

Use torque sequence below
aca9f77.gif

Sep 17, 2009 | 1994 Mazda 2WD B Series Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

147 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...